SONY XAV-AX5500 Bluetooth Media Receiver Instruction Manual

AV RECEIVER

Operating Instructions

To cancel the demonstration (Demo) display, see page 8.
To switch the FM/AM tuning step, see page 7.
For the connection/installation, see page 12.

Warning

For safety, be sure to install this unit in the dashboard of the car as the rear side of the unit becomes hot during use.
For details, see “Connection/Installation” (page 12).

The nameplate indicating operating voltage, etc., is located on the bottom of the chassis.
The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area) and Switzerland.

WARNING
To prevent fire or shock hazards, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Disposal of waste batteries and electrical and electronic equipment (applicable in the European Union and other countries with separate collection systems)

WARNING: Do not ingest battery, Chemical Burn Hazard.

The remote commander contains a coin/ button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.  If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Note on the lithium battery
Do not expose the battery to excessive heat such as direct sunlight, fire, or the like.

Warning if your car’s ignition has no ACC position
Do not install this unit in a car that has no ACC position. The display of the unit does not turn off even after turning the ignition off, and this causes battery drain.

Disclaimer regarding services offered by third parties
Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations.

Important notice

Caution
IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF  REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED  EQUIPMENT, DOWNTIME, AND PURCHASER’S TIME RELATED TO  OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE.

Dear customer, this product includes a radio transmitter.
Please check your vehicle operation manual or contact the manufacturer of your vehicle or your vehicle dealer, before you install this product into your vehicle.

Emergency calls
This BLUETOOTH car is handsfree and the electronic device connected to the handsfree operates using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions. Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies).

On BLUETOOTH communication

• Microwaves emitting from a BLUETOOTH device may affect the operation of electronic medical devices. Turn off this unit and other BLUETOOTH devices in the following locations, as it may cause an accident.
  – where inflammable gas is present, in a hospital, train, airplane, or petrol station
  – near automatic doors or a fire alarm

• This unit supports security capabilities that comply with the BLUETOOTH standard to provide a secure connection when the BLUETOOTH wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using BLUETOOTH wireless technology.

• We do not take any responsibility for the leakage of information during BLUETOOTH communication.
  If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.

Guide to Parts and Controls

Main Unit and Remote Commander

The VOL (volume) + button has a tactile dot.

1. Display/touch screen
   

2. HOME
   Displays the HOME screen (page 6).
   ATT (attenuate)
   Press and hold for 1 second to attenuate the sound. To cancel, press and hold again, or press VOL +.

3. VOL (volume) +/–

4. Receptor for the remote commander

5. / (previous/next)
   Functions differently depending on the selected source:
   – Radio: select a preset station.
   – USB/BT Audio: move to the previous/next file.
   Press and hold to:
   – Radio: Tune into a station automatically
   (SEEK+/SEEK–).
   – USB/BT Audio: fast-reverse/fast-forward.

6. OPTION
   Displays the OPTIONS screen (page 6).
   VOICE
   Press and hold to activate the voice command function for Apple CarPlay and Android Auto™.
   RM-X170 remote commander
   The remote commander can be used to operate the audio controls. For menu operations, use the touch screen. Note
   The white buttons in the illustration above are not supported.

7. OFF
   Turns the source off.

8. MONITOR OFF
   Turns off the monitor.
   To turn back on, press again.

9. EQ (equalizer)
   Selects an equalizer curve.

10. Number buttons (0 to 9)

11. CLEAR

12. ATT (attenuate)
    Attenuates the sound. Press again to cancel the attenuation.

13. (play/pause)

14. (previous/next)
    (fast-reverse/fast-forward)
    Functions differently depending on the selected source:
    – Radio: select a preset station.
    – USB/BT Audio: move to the previous/next file.
    Press and hold to:
    – Radio: Tune into a station automatically
    (SEEK+/SEEK–).
    – USB/BT Audio: fast-reverse/fast-forward.

15. Functions differ depending on the selected source.
    – Radio: select a preset station or tune into a station automatically.
    – USB: select a folder or move to the previous/ next file.
    ENTER
    Enters the selected item.

16. SRC (source)
    Changes the source. Each time you press this button, a selectable source is displayed in a popup on the current display.

17. MODE
    Selects the radio band.

18. VOL (volume) +/–
    Remove the insulation film before use.

Screen displays

Playback screen:

HOME screen:

OPTION screen:

1. Status indication
   Lights up when the sound is attenuated.
   Lights up when the Bluetooth® signal is on. Flashes when the connection is in progress.
   Lights up when the audio device is playable by enabling the A2DP (Advanced Audio Distribution Profile).
   Lights up when handsfree calling is available by enabling the HFP (Handsfree Profile).
   Indicates the signal strength status of the connected mobile phone.
   Indicates the remaining battery status of the connected mobile phone.

2. (source option)
   Opens the source option menu. The available items differ depending on the source.

3. Application specific area
   Displays playback controls/indications or show the unit’s status. Displayed items differ depending on the source.

4. Clock
   Displays the time which is set on the date/time setting.

5. (return to the playback screen)
   Switches from the HOME screen to the playback screen.

6. Sources and Settings select keys
   Changes the source or make various settings.
   Flick to select the setting icon and other icons.
   Touch the source icon you want to select.  Android Auto|  Apple CarPlay| Radio
   ---|---|---
   BT Audio| Phone|  USB port 1
   WebLink| USB port 2|  Camera
   Settings| |

7. Sound select keys
   Changes the sound.

8. (standby)
   Turns the unit in standby mode (USB charging is still available). To resume, press any buttons.

9. (monitor off)
   Turns off the monitor. When the monitor is turned off, touch any part of the display to turn it back on.

10. (EXTRA BASS)
    Changes the EXTRA BASS setting.

11. (EQ10/subwoofer)
    Changes the EQ10/subwoofer set.

Basic Operations

Switching the FM/AM Tuning Step
Set the FM/AM tuning step of your country or region.

1. Press HOME, touch [Settings] → [General] →
   [Tuning Steps], then set the FM/AM tuning step.

2. To exit the setup menu, touch (back) three times.

Pairing with a BLUETOOTH Device
When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other.

1. Press HOME, then touch [Settings] →[Bluetooth] → [Bluetooth Connection] → [ON] → [Pairing]. flashes while the unit is in pairing standby mode.
2. Perform pairing on the BLUETOOTH device so it detects this unit.
3. Select your model name shown on the display of the BLUETOOTH device*.
   When pairing is made, stays lit.

• If passkey input is required on the BLUETOOTH device, input [0000].

Connecting Rear View Camera

By connecting the optional rearview camera to the CAMERA IN terminal, you can display the picture from the rearview camera. For details, see “Connection/Installation” (page 12).

To display the picture from the rearview camera
Press HOME, then touch [Rear Camera].

Canceling the Demonstration Mode

1. Press HOME, then touch [Settings].
2. Touch [General], then touch [Demo] to set to [OFF].
3. To exit the setup menu, touch (back) twice.

Updating the Firmware

To update the firmware, visit the support site on the back cover, then follow the online instructions.
Note
During the update, do not remove the USB device.

Additional Information

Precautions

• Power antenna (aerial) extends automatically.
• When you transfer ownership or dispose of your car with the unit installed, initialize all the settings to the factory settings by performing the factory reset.
• Do not splash liquid onto the unit.

Notes on safety

• Comply with your local traffic rules, laws, and regulations.

• While driving
  – Do not watch or operate the unit, as it may lead to distraction and cause an accident. Park your car in a safe place to watch or operate the unit.
  – Do not use the setup feature or any other function which could divert your attention from the road.
  – When backing up your car, be sure to look back and watch the surroundings carefully for your safety even if the rearview camera is connected.
  Do not depend on the rearview camera exclusively.

• While operating
  – Do not insert your hands, fingers, or foreign objects into the unit as it may cause injury or damage to the unit.
  – Keep small articles out of the reach of children.
  – Be sure to fasten seatbelts to avoid injury in the event of sudden movement of the car.

Preventing an accident
Pictures appear only after you park the car and set the parking brake.
If the car starts moving during video playback, the following caution is displayed and you cannot watch the video.
[Video blocked for your safety.]
Do not operate the unit or watch the monitor while driving.

Notes on the LCD panel

• Do not get the LCD panel wet or expose it to liquids. This may cause a malfunction.
• Do not press down hard on the LCD panel as doing so can distort the picture or cause a malfunction (i.e., the picture may become unclear or the LCD panel may be damaged).
• Do not touch the panel with objects other than with your finger as it may damage or break the LCD panel.
• Clean the LCD panel with a dry soft cloth. Do not use solvents such as benzene, thinner, commercially available cleaners, or antistatic spray.
• Do not use the unit outside the temperature range 0 ºC to 40 ºC (32 ºF to 104 ºF).
• If your car was parked in a cold or hot place, the picture may not be clear. However, the monitor is not damaged and the picture will become clear after the temperature in your car becomes normal.
• Some stationary blue, red, or green dots may appear on the monitor. These are called “bright spots” and can happen with any LCD. The LCD panel is precision-manufactured with more than 99.99% of its segments functional. However, it is possible that a small percentage (typically 0.01%) of the segments may not light up properly. This will not, however, interfere with your viewing.

Notes on the touch screen

• This unit uses a capacitive touch screen. Touch the screen directly with your fingertip.
• Multi-touch operation is not supported on this unit.
• Do not touch the screen with sharp objects such as a needle, pen, or fingernail. Operation with a stylus is not supported on this unit.
• Touching the screen with a gloved finger may cause the unit to operate incorrectly or not respond.
• Do not let any objects contact the touch screen. If the screen is touched by an object other than your fingertip, the unit may not respond correctly.
• Since glass material is used for the screen, do not subject the unit to strong shock. If cracking or chipping occurs on the screen, do not touch the damaged part as it may cause injury.
• Keep other electrical devices away from the touch screen. They may cause the touch screen to malfunction.
• If there are water droplets on the touch screen, or if you touch the screen with wet fingertips, the touch screen may not react correctly.

About iPhone

• Compatible iPhone models:
  iPhone XS Max, iPhone XS, iPhone XR, iPhone X,
  iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7,
  iPhone SE, iPhone 6s Plus, iPhone 6s,
  iPhone 6 Plus, iPhone 6, iPhone 5s

• Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards.
  Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
  Please note that the use of this accessory with an Apple product may affect wireless performance.

Notice on license

This product contains software that Sony uses under a licensing agreement with the owner of its copyright. We are obligated to announce the contents of the agreement to customers under requirement by the owner of the copyright for the software.
For details on software licenses, select [Settings] → [General] → [Open Source Licenses].

If you have any questions or problems concerning your unit that are not covered in these Operating Instructions, consult your nearest Sony dealer.

Maintenance

Replacing the lithium battery (CR2025) of the remote commander
When the battery becomes weak, the range of the remote commander becomes shorter.

CAUTION
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.

Note on the lithium battery
Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor.

Specifications

Monitor section
Display Type: Wide LCD color monitor
Dimensions: 6.95 in/176 mm
System: TFT active matrix
A number of pixels:
1,152,000 pixels (800 × 3 (RGB) × 480)
Color system:
PAL/NTSC automatic select for CAMERA IN terminal

Radio section
FM
Tuning range:
87.5 MHz – 108.0 MHz (at 50 kHz step)
87.5 MHz – 108.0 MHz (at 100 kHz step)
87.5 MHz – 107.9 MHz (at 200 kHz step)
FM tuning step:
50 kHz/100 kHz/200 kHz switchable
Usable sensitivity: 7 dBf
Signal-to-noise ratio: 70 dB (mono)
Separation at 1 kHz: 45 dB
AM
Tuning range:
531 kHz – 1,602 kHz (at 9 kHz step)
530 kHz – 1,710 kHz (at 10 kHz step)
AM tuning step:
9 kHz/10 kHz switchable
Sensitivity: 32 μV

USB player section
Interface:
USB port 1 (Hi-speed)
USB port 2 (Full-speed)
Maximum current:
USB port 1: 1.5 A
USB port 2: 500 mA

Wireless communication
Communication System:
BLUETOOTH Standard version 3.0
Output:
BLUETOOTH Standard Power Class 2
(Max. Conducted +1 dBm)
Maximum communication range*1:
Line of sight approx. 10 m (33 ft)

Frequency band:
2.4 GHz band (2.4000 GHz – 2.4835 GHz)
Modulation method: FHSS
Compatible BLUETOOTH Profiles2:
A2DP (Advanced Audio Distribution Profile) 1.3
AVRCP (Audio Video Remote Control Profile) 1.3
HFP (Handsfree Profile) 1.6
PBAP (Phone Book Access Profile) 1.1
Corresponding codec: SBC, AAC
1 The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity,
antenna (aerial)’s performance, operating system, software application, etc.
*2 BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices.

Power amplifier section
Outputs: Speaker outputs
Speaker impedance: 4 Ω – 8 Ω
Maximum power output: 55 W × 4 (at 4 Ω)

General
Power requirements: 12 V DC car battery (negative ground (earth))
Rated current consumption: 10 A
Dimensions:
Approx. 178 mm × 100 mm × 139 mm (7 1/8 in × 4 in × 5 1/2 in) (w/h/d)
Mounting dimensions:
Approx. 182 mm × 111 mm × 120 mm (7 1/4 in × 4 3/8 in × 4 3/4 in) (w/h/d)
Mass: Approx. 1.0 kg (2 lb 4 oz)
Package contents:
Main unit (1)
Parts for installation and connections (1 set)
Remote Commander (1): RM-X170
Ask the dealer for detailed information.
Design and specifications are subject to change without notice.

Copyrights
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners.

Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United
States and/or other countries.

This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.

Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
Apple CarPlay is a trademark of Apple Inc.

Android Auto is a trademark of Google LLC.

WebLink is a registered trademark of Abalta
Technologies, Inc. in the U.S. and a trademark in the other countries.

All other trademarks are trademarks of their respective owners.

Connection/Installation

Cautions

• Do not install this unit in a car that has no ACC position. The display of the unit does not turn off even after turning the ignition off, and this causes battery drain.
• Run all ground (earth) leads to a common ground (earth) point.
• Do not get the leads trapped under a screw or caught in moving parts (e.g., seat railing).
• Before making connections, turn the car ignition off to avoid short circuits.
• Connect the yellow and red power supply leads only after all other leads have been connected.
• Be sure to insulate any loose unconnected leads with electrical tape for safety.
• Choose the installation location carefully so that the unit will not interfere with normal driving operations.
• Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a safe and secure installation.

Note on the power supply lead (yellow) When connecting this unit in combination with other stereo components, the amperage rating of the car circuit to which
the unit is connected must be higher than the sum of each component’s fuse amperage rating.
Note on installing in cars with a start-stop system The unit may restart when starting the engine from start-stop. In this case, turn off the start- stop system of your car.
Note on installing in cars with electric parking brake system
For cars with electric parking brakes, some related functions (such as video blocking functions) may not work properly.
Mounting angle adjustment
Adjust the mounting angle to less than 30°.

Parts List for Installation

This parts list does not include all the package contents.

Connection

1 Not supplied
2 Speaker impedance: 4 Ω to 8 Ω × 4
3 RCA pin cord (not supplied)
4 Depending on the type of car, use an adaptor for a wired remote control (not supplied).
For details on using the wired remote control, see “Using the wired remote control” (page 15).
5 Depending on the type of car, use an adaptor (not supplied) if the antenna (aerial) connector does not fit.
6 Whether in use or not, route the microphone input cord so it does not interfere with driving operations. Secure the cord with a clamp, etc., if it is installed around your feet.
7 For details on installing the microphone, see “Installing the microphone” (page 14).
8

*9 When using the steering wheel remote control, use the connection cable RC-SR1 8 as necessary.

Making connections

1. To a common ground (earth) point
   First connect the black ground (earth) lead then connect the yellow and red power supply leads.

2. To the +12 V power terminal which is energized at all times
   Be sure to first connect the black ground (earth) lead to a common ground (earth) point.

3. To the +12 V power terminal which is energized when the ignition switch is set to the accessory position
   Be sure to first connect the black ground (earth) lead to a common ground (earth) point.

4. To the power antenna (aerial) control lead orthe power supply lead of the antenna (aerial) booster
   It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial).
   To AMP REMOTE IN of an optional power amplifier
   This connection is only for amplifiers and a power antenna (aerial). Connecting any other system may damage the unit.
   Note
   It will take about 10 seconds to shut down the output of
   REM OUT after the unit is turned off.

5. To a car’s illumination signal
   Be sure to first connect the black ground (earth) lead to a common ground (earth) point.

6. To the parking brake switch lead
   The mounting position of the parking brake switch lead depends on your car.
   Be sure to connect the parking brake lead (light green) of the power supply leads 1 to the parking brake switch lead.
   

7. To the +12 V power terminal of the car’s rear lamp lead (only when connecting the rear view camera)

Memory hold connection
When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Speaker connection

• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 Ω to 8 Ω and with adequate power handling capacities to avoid damage.

Installing the microphone

To capture your voice during hands-free calling, you need to install the microphone 3.

Cautions

• It is extremely dangerous if the cord becomes wound around the steering column or gearstick.
  Be sure to keep it and other parts from interfering with your driving operations.

• If airbags or any other shock-absorbing equipment are in your car, contact the store where you purchased this unit or the car dealer before installation.
  Notes

• When mounting on the dashboard, remove the visor clip carefully from the microphone, then attach the flat-mount base to the microphone.

• Before attaching the double-sided tape, clean the surface of the dashboard with a dry cloth.

Using the wired remote control

When using the steering wheel remote control
Installation of the connection cable RC-SR1  is required before use.
1 To enable the steering wheel remote control, select
[General]  [Steering Control]  [Custom]  to make the registration.
When the registration is complete, the steering wheel remote control becomes available.
Notes on installing the connection cable RC-SR1
• Refer to the support site on the back cover for details then connect each lead properly to the appropriate leads.
Making an improper connection may damage the unit.
• Consulting the dealer or an experienced technician for help is recommended.
When using the wired remote control
1 To enable the wired remote control, set [Steering Control] in [General] to [Preset].

Using the rearview camera

Installation of the rearview camera (not supplied) is required before use.
The picture from a rearview camera connected to the CAMERA IN terminal is displayed when:
– the back lamp of your car lights up (or the shift lever is set to the R (reverse) position).
– you press HOME, then touch [Rear Camera].

Installation

Mounting the unit in a Japanese car
You may not be able to install this unit in some Japanese cars. In such a case, consult your Sony dealer.

When mounting this unit to the preinstalled brackets of your car, use the mounting screws in the appropriate screw holes based on your car: T for TOYOTA and N for NISSAN.
Note
To prevent a malfunction, install only with the mounting screws 2.

Fuse replacement

When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. f the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.

Support site
If you have any questions or for the latest support information on this product, please visit the website below: https://www.sony-asia.com/support

Help Guide (online manual)
For more details, please visit the following website and refer to your unit name as shown below.

XAV-AX5500(IN)
https://rd1.sony.net/help/ev/xav-ax55/h_zz

©2020 Sony Corporation Printed in Thailand
https://www.sony.net/

References

• dtsc.ca.gov/hazardouswaste/perchlorate
• SiriusXM: Music, Sports, Talk & Podcasts, Live & On Demand
• Help Guide | Top
• Sony Group Portal - Home
• Select your country or region | Sony USA
• Support for Sony products | Sony USA
• Sony Corporation - Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>