Shenzhen Qualitronic Technology 962BT Bluetooth LED Speaker User Manual
- June 6, 2024
- Shenzhen Qualitronic Technology
Table of Contents
962BT
Bluetooth LED Speaker
Product description
Function keys
1. LED
2. Mode Button
3. Skip/Volume – Button (-)
4. Play/Pause Button
5. Skip/Volume + Button (+)
6. BASS Button
7. ON/OFF Switch| 8. Aux. Port
9. TF Card Slot
10. USB Port
11. 5V = Charging Port
12. Charging Indicator Light
13. MIC Port
---|---
Specifications
Bluetooth Version: 5.0
Wireless Range: 8-10m
Speaker Output: 10W
Power Supply: 5V 1A
Rechargeable Battery: 2400mAh
Sensitivity: 75DB
Impedance: 3Ω
Frequency Range: 150HZ-20KHZ
Operating Frequency: 2.4GHz
Features: BT/USB/TF/AUX/FM/TWS/MIC/Bass
Instructions for Use
Charging the Battery
The speaker is fitted with a 3.7V 2400mAh rechargeable battery (non-
removable). It is recommended that the battery is fully charged before first
use; this will take approx. 4 to 5 hours. Connect the micro USB end of the USB
charging cable into the 5V charging port on the back of the speaker and the
other end to a compatible USB port.
Whilst charging, the charging indicator light will illuminate red. Once the
battery has fully charged, the charging indicator light will switch off.
Carefully disconnect both ends of the USB charging cable and store it safely
for future use.
Using the Bluetooth LED Speaker
Basic Functionality
Turn on the speaker by sliding the “ON/OFF” switch to the “ON”
POSITION. Pause a track by pressing push it again to resume the track.
Adjust the volume of the speaker using and . Press and hold to increase the
volume； decrease the volume by pressing and holding .
To switch to the next track, press plays the previous track by pressing .
Cycle between modes by pressing ‘M’ until the desired operation is selected.
Modes
The speaker must be turned on before using any of the following modes.
Bluetooth Mode
Pairing with a Bluetooth Compatible Device
STEP 1: Once the speaker has been turned on, a tone will play to signal it is
ready to be paired with a Bluetooth-compatible device.
STEP 2: Search for the speaker using a Bluetooth-compatible device. Select
‘962BT’ to connect and pair. Once a connection has been made, the speaker will
play a tone to signal that the devices are paired.
STEP 3: To unpair or remove a Bluetooth compatible device from the speaker,
turn off the Bluetooth function on the compatible device. The speaker can now
be paired with a new compatible device.
Note: Once connected, sound can be controlled using either the speaker or the
relevant controls on the Bluetooth-compatible device.
Aux. Mode
Connect one end of the Aux. cable to the Aux. input port on the speaker and
the other end to an MP3 player or another compatible audio source.
The speaker will automatically switch to Aux. mode once the line-in Aux. cable
has been inserted.
Note: Sound can now be controlled using the relevant controls on the
compatible audio source; the speaker cannot be used to skip tracks during Aux.
mode.
If the speaker does not automatically switch to Aux. mode once the line-in
Aux. cable (not included) is inserted, press ‘M’ until it
is selected.
Micro SD Card/USB Mode
STEP 1: To use micro SD card mode, insert a micro SD card (not included) into
the micro SD card slot. The speaker will automatically change to micro SD card
mode.
STEP 2: To use USB mode, insert a compatible USB drive into the USB port, The
speaker will automatically change to a USB mode.
STEP 3: If the speaker does not automatically change to micro SD card or USB
mode, press ‘M’ until the desired operation is selected.
Note: Once connected, sound can be controlled using the speaker.
No USB drive should be inserted whilst using micro SD card mode or vice versa,
as this could interfere with playback.
The speaker will only recognize MP3 audio files; if other files are present on
the Micro SD card or USB drive, this may prevent the speaker from playing.
Troubleshooting
The speaker has no power.
The speaker has run out of charge. Charge the speaker following the
instructions in the section entitled ‘Charging the Battery’.
The speaker has no sound.
The volume level is set too low. Check that the volume level is set at an
audible level and adjust accordingly.
The speaker is not paired with a Bluetooth-compatible device. Follow the
instructions in the section entitled “Bluetooth Mode’.
The speaker is not connected to a compatible audio source. Follow the
instructions in the section entitled ‘Aux. Mode’.
Unable to pair a Bluetooth device with the speaker.
The Bluetooth device is not compatible with the speaker. Check that the
Bluetooth device is compatible with the speaker and that the Bluetooth
function is switched on.
The charge of the speaker depletes quickly.
The volume level is set too high. Excessive use of the speaker at high volumes
will drain the battery quickly. Charge the speaker following the instructions
in the section entitled ‘Charging the Battery’ and listening at a lower volume
for better results.
The battery may be reaching the end of its service life and the unit will need
to be disposed of.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party. Responsible for compliance could void the user’s
authority to operate this equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirements.
The device can be used in the portable exposure condition with restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>