Shenzhen Hengxintai Electronics BT9510 ANC Headphone Instructions
- June 6, 2024
- Shenzhen Hengxintai Electronics
Table of Contents
Shenzhen Hengxintai Electronics BT9510 ANC Headphone Instructions
Product Specification
Bluetooth Version : V5.0
Bluetooth Range : 10meters
Headphone Battery : 350mAh
Standby Time : up to 200 hours
Working Time : up to 12 hours (ANC OFF)
Working Time : up to 9 hours (ANC ON)
Charging Time : Approx 1.5 hours
Input Voltage : 5V
Microphone : Build-in
Recgargable : USB cable
Speaker Unit : 40mm
Rated imput power : 20mW
Max input power : 50mW
Impedance : 32ohm
Sensitivity : 95dB+/-3dB
Frequency Response : 20Hz – 20KHz
Noise reduction： 20dB+/-2dB
FUNCTION PICTURE
Description of all parts
- ANC button
- Volume up or Next song
- Power on/off or Pause/Play or Calling/Answer
- Volume down or Previous song
- 3.5mm Aux Jack
- LED light
- USB charging port
- Build in Microphone
Pairing Steps
- Press for 5 seconds to put into pairing mode (the indicator light will alternate between red and blue).
- Go to your Bluetooth settings on your device and find the Bluetooth pairing name “ANC headphone ”. Pair your device, then it will be connected, when connected successfully, only blue light flash.
Product Usage
-
Power on
Press and hold the for about 3 seconds, untill blue light flashes. -
Power off
Press and hold for about 3 seconds, the indicator light will turn off . -
Answer a call
when a call is coming in , Answer the call by pressing once. -
Reject a call
Press and hold for about 2 seconds. -
Redialing the last number
Double click button. -
Volume
”+” and next song : Press quickly for next song, the volume will be increased by pressing and holding for a long time. -
Volume
“-” and previous song : Press quickly for previous song, the volume will be decreased by pressing and holding for a long time . -
Play / Pause music
when you listen to the music, you can play or pause the song by pressing button. -
ANC mode
Push button to open / close the funtion. -
Reconnected : when reopen the bluetooth mode , the headphone will reconnect to the nearest devices.
-
When insert the line in or USB cable , the headphone will power off rapidly , then switch to wired mode , and all bluetooth buttons are not workable.
-
Charging port with USB charging cable . The red light will show during charging, But turn off once the device is fully charged.
FC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. -
Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction