Shelly-TRV Wi-Fi Operated Thermostatic Radiator Valve Instruction Manual
- June 6, 2024
- Shelly
Table of Contents
Shelly-TRV Wi-Fi Operated Thermostatic Radiator Valve
View all Shelly thermostat manual
Introduction
⚠RECOMMENDATION! This user guide is subjective to adjustments. For the
latest version, please
visit: https://shelly.cloud/knowledge-base/devices/shelly-trv/
Download the Shelly Cloud Application by scanning the QR code above, or access
the devices through the Embedded web interface, explained further down in the
user guide. Shelly devices are compatible with Amazon Echo and Google Home
supported functionalities, as well as other home automation platforms and
voice assistants. See details at https://shelly.cloud/support/compatibility/
Registration
The first time you load the Shelly Cloud mobile app, you have to create an
account which can manage all your Shelly devices. You need to use an actual
e-mail because that e-mail will be used in case of а forgotten password!
Forgotten Password
In case you forget or lose your password, click the “Forgot Password?” link on
the login screen and type the e-mail you used in your registration. You will
receive an e-mail with а link to а page where you can reset your password. The
link is unique and can be used only once.
⚠ATTENTION! If you are unable to reset your password, you have to reset
your device (as explained in “Device Inclusion” section, Step 1).
First steps
After registering, create your first room (or rooms), where you are going to
add and use your Shelly devices. Shelly Cloud allows you to create scenes for
automatic control of devices at predefined hours or based on other parameters
like temperature, humidity, light, etc. (with available sensors in Shelly
Cloud). Shelly Cloud allows easy control and monitoring using a mobile phone,
tablet, or PC. Shelly TRV can be grouped with other devices in the
application. It can also be set to trigger actions on other Shelly devices,
run schedules, scenes, and webhooks.
THE SHELLY APP
Device Inclusion
Step 1
When the installation of Shelly TRV is done and the power is turned on, Shelly
will create its own Wi-Fi Access Point (AP).
⚠WARNING! In case the device has not created its own AP Wi-Fi network
with SSID like Shelly-TRV-f008d1d8bd68, please check if the device is
installed according to the “Installation Instructions”.
If you still do not see an active Wi-Fi network with SSID i.e. ShellyTRV-
f008d1d8bd68, or you want to add the device to another Wi-Fi network, reset
the device. The reset button is next to the charging port (exact location
shown in “User and Safety Guide”), and with a pin, press and hold it for 5 sec
to enter AP mode again, or 10 sec to do a factory reset.
If you’re having difficulties with setting up your device, please contact us
at: support@shelly.cloud
Step 2
Please keep in mind that Shelly devices’ inclusion is different on iOS and
Android devices.
-
iOS inclusion – Open the settings menu on your iOS device > “Аdd device” and connect to the Wi-Fi network created by your Shelly device, i.e. Shelly-TRV-f008d1d8bd68 (fig. 1). Open your Shelly App again and type in your home Wi-Fi credentials (fig.2). After clicking “Next”, a menu will open allowing you to choose the device which you want to include, or include any found in the network.
-
Android inclusion – From the hamburger menu on the main screen of your Shelly App choose “Add device“. Then choose your home network and type in your password (fig. 3). After that, pick the Shelly device you want to include. The name of the device will be similar to: ShellyTRV-f008d1d8bd68 (fig. 4).
Step 3
Approximately 30 sec. after discovering any new devices оn the local Wi-Fi
network, а list will be displayed in the “Discovered Devices” room by default.
Step 4
Select “Discovered devices” and choose the device you want to include in your
account.
Step 5
Enter a name for the device (in the “Device Name” field). Choose a ”Room”
where the device will be positioned and controlled from. You can choose an
icon or add a picture to make it easier to recognize. Press “Save device”.
Step 6
To control Shelly devices only through the local network, press “No”
Device settings
After your Shelly TRV is added in the application, you can control it, change its settings, and automate the way it works. To switch the device on and off, use the ON/OFF button. То change temperature, simply click the plus and minus signs. For device management, click on the device’s name. From there you may control the device, as well as edit its appearance and settings. Once you click on the device, you will see the current temperature displayed on the left, under the device’s picture. Next to it, you can see how much percent (%) the valve is open. The third icon shows battery level (%).
Weekly Schedules
Upon pressing “Weekly Schedules”, you see the different profile choices (up to
5) that you’ve set, and below your weekly schedules. “Active schedules” shows
you the weekly schedules that you have set for this profile, which can be up
to 20. The graph illustrates the weekly schedule for the chosen profile.
Active Schedules
From here, you can set up to 20 weekly schedule for each of the 5 profiles.
Temperature
This graph shows minimum and maximum measured temperature for each hour, day,
week, month or year, depending on the setting you’ve chosen. From the graph
button on the right, you can change the layout of the graph itself (bar chart,
line graph, etc).
Sensor settings
When Shelly TRV is measuring the temperature in big rooms, a difference might
exist between the actual temperature and the temperature measured by Shelly
TRV, called the temperature offset. From here, you can set the temperature
offset to +2 if your thermometer or external sensor detects 24°C while Shelly
TRV measures 22°C, as it’s closer to the radiator. Values can be between -9°
and +9°C.
I/O Actions:
Set URLs to hit when a certain action is being completed by the device. These
changes will be applied when the device wakes up.
- Valve_open: URLs to hit when valve is open.
- Valve_close: URLs to hit when valve is closed.
Internet
- Wi-Fi 1: Allows the device to connect to an available Wi-Fi network. After typing the details in the respective fields, press Connect.
- Access Point: Configure Shelly to create a Wi-Fi Access point. After typing the details in the respective fields, press Create Access Point.
- Cloud: Connection to the cloud allows you to control your device remotely and to receive notifications and updates.
- Bluetooth: Enable/disable.
- MQTT: Configure the Shelly device to communicate over MQTT.
Application Settings:
- Exclude from Event Log: Do not show events from this device in the app.
- Sync name: Keep the device name in sync with the name given in the app.
Share
Share the control of your device with other users.
Settings:
- Auto-temperature control: Check if you want your device to maintain constant room temperature. If not, when automatic control is turned off, Manual mode control (in %) can be set from buttons.
- Display: Set the display brightness (low – high) and rotate the screen 180°.
- Child lock: Allows you to enable child lock and target temperature will not be changed from butons.
- Firmware version: Shows your current firmware version. If a newer version is available, you can update your Shelly device by clicking Update.
- Geo Location And Time Zone: Set your time zone and geo-location manually, or enable/disable automatic detection.
- Device Reboot: Reboot your Shelly TRV.
- Factory Reset: Remove Shelly TRV from your account and return it to its factory settings. This will delete all set data.
- Device Information: Here you can view the ID, IP and other settings of your device. Upon clicking “Edit device”, you can change the room, name or image of the device.
THE EMBEDDED WEB INTERFACE
INITIAL INCLUSION
Step 1
Install Shelly following the connection diagrams described in the “User and
Safety Guide” with the device, and place it into the breaker box. After
pressing the reset button, Shelly TRV will create its own Wi-Fi network (AP).
⚠WARNING! If you don’t see the AP, please fоllow step 1 from the “Device
Inclusion” section of this guide.
Step 2
Shelly TRV has created its own Wi-Fi network (AP), with name (SSID) such as
Shelly-TRV-f008d1d8bd68. Connect to it with your phone, tablet, or PC.
Step 3
Type 192.168.33.1 into the address eld of your browser to load the web
interface of Shelly.
GENERAL- HOME PAGE
This is the home page of the embedded web interface. If it has been set up correctly, you will see information about the state of Shelly TRV, current and set temperature, and different menus for control.
- Red button: Bring target temperature up 1°C
- Blue arrow: Bring target temperature down 1°C
- Target room temperature in °C
- Current room temperature in °C
Sensor settings
When Shelly TRV is measuring the temperature in big rooms, a difference might
exist between the by Shelly TRV, called the temperature offset. From here, you
can set the temperature offset to +2 if your thermometer or external sensor
detects 24°C while Shelly TRV measures 22°C, as it’s closer to the radiator.
Values can be between -9° and +9°C.
Weekly Schedule
Set up to 5 profiles and up to 20 weekly schedules for them
Internet & Security
- Wi-Fi Mode – Client: Allows the device to connect to an available Wi-Fi network. In order to switch to this mode, the User must enter the name (SSID) and the password to con- nect to a local Wi-Fi network. After entering the correct details, press Connect.
- W-Fi Mode – Access Point: Allows the Device to operate as a Wi-Fi access point. The User can change the name (SSID) and the password to access the AP. After you have entered the desired settings, press Connect.
- Restrict Login: Restrict the web interface of the Shelly device with “Username” and “Password
- SNTP server: Synchronizes a computer’s system time with a server. Default is set to time.google.com
- MQTT: Configure the Shelly device to communicate over MQTT.
- CoIoT: Configure the Shelly device to communicate over CoIoT.
- Cloud: Connection to the cloud allows you to control your device remotely and to receive notifications and updates.
Actions
From here, you can set actions that the device will execute after the valve
has been opened or closed. Мore than 2 actions can affect the normal operation
of the device depending on the network infrastructure and the controlled
devices.
- Valve is opened. This will be repeated every 5 minutes while the valve is partially or fully opened.
- Valve is closed. This will be called only once, when the valve gets fully closed.
Settings:
- Auto-temperature control: Check if you want your device to maintain constant room temperature. If not, when automatic control is turned off, Manual mode control (in %) can be set from buttons.
- Display: Set the display brightness (low – high) and rotate the screen 180°.
- Child lock: Allows you to enable child lock and target temperature will not be changed from butons.
- Firmware version: Shows your current firmware version. If a newer version is available, you can update your Shelly device by clicking Update.
- Geo Location And Time Zone: Set your time zone and geo-location manually, or enable/disable automatic detection.
- Device Reboot: Reboot your Shelly TRV.
- Device Calibrate: Calibrate your Shelly TRV.
- Factory Reset: Remove Shelly TRV from your account and return it to its factory settings. This will delete all set data.
- Device Information: Here you can view the ID, IP and other settings of your device. Upon clicking “Edit device”, you can change the room, name or image of the device.
Shelly TRV WiFi Operated Thermostatic Radiator Value User Guide
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>