SUNPENTOWN SR-18AR 1800W Built-In Smartscan Commercial Range Induction Cooker Instruction Manual

•  LED displays a one or two-digit number, indicating the power level (1-20)
•  The unit will con tenuously cook un l: manually shut off.

In Func on (TEMP indicator is on):

• LED displays a two or three-digit number, indica ng cooking temperature. (90°F to 440°F, in 10°F increments)
•  The unit will cook un l set temperature is reached and will keep warm.
•  When a set temperature is reached, the unit will stop heating. The unit starts heating again when it senses the temperature has dropped below seeing.
•  Temperature difference: when cooking a large pot of soup or other contents, please be advised that the temperature inside the pot will vary from point to point. For example, the bottom sec on (closest to cooktop) will be a bit hotter than the middle sec on. The type and quality of cookware can affect temperature transfer.

HOW TO USE

1.  Plug in power cord(refer to Specifica ons on Page 10 for correct power input) , unit will beep once.
2.  Please suitable cookware and add food contents.
3.  Press ON/OFF button (red indicator light will illuminate, COOK mode by default).
4.  Press COOK/TEMP button to select setting
   • COOK mode: LED displays power level: 1~20
   • TEMP mode: LED displays temperature: 90~440°F
5. Turn knob clockwise/counter-clockwise to set power level or temperature.
6. When cooking is done, turn unit off by pressing ON/OFF button.

NOTE:

• Safety feature: if no cookware is placed, unit will shut off after 2 minutes.
•  To avoid temperature jump, please cook at least 1 quart of food/content.
• Actual temperature (in TEMP mode) may vary slightly due to different variables, such as: surrounding temperature, content and volume of food, and if using a lid, etc.
• Use flat cookware and place in center of plate.
•  When using cookware that is not flat or with an uneven bottom, the set temperature will be VERY different from the actual temperature.

ATTENTION

• Always place cookware or other objects on the top plate gently as the ceramic plate may crack under force.
• Please use suitable cookware, otherwise abnormal cooking or damage may occur.
• The self-protect circuit will protect the unit when power supply is unstable.
• The red power light will be flashing and cooking will stop.

KEY POINTS BEFORE USING THE COOKTOP

• Please plug this cooktop in the correct 15-amp outlet.
• Do not share the outlet with other appliances and make sure it is correctly plugged in.
•  Do not touch the ceramic plate immediately after cooking, the plate may remain hot due to heat transferred from the cookware.
•  Do not insert any object in the inlet or outlet to prevent electric shock.
• Do not damage the ceramic plate.
• If the ceramic plate is broken, please turn unit off and unplug from outlet immediately.

IMPORTANT:

• If the electric cord is damaged, please contact our service technician for a replacement.
• This appliance is equipped with overheat protec on feature.
• Those with a pacemaker should consult they physician before using this item.
• If the cooktop surface is broken or cracked, do not use the product as it may cause electric shock.

EMERGENCY PROCEDURES
If the cooktop is not working properly, please contact our service technician for assistance. Do not disassemble the unit by yourself.

LIST OF SUITABLE / UNSUITABLE COOKWARE

Maintaining the product

• Unplug the cord before any cleaning is done.
• To clean the ceramic plate, use a soft sponge with dish detergent. Then wipe clean with damp towel.
• Clean fan intake with vacuum whenever necessary.

DO NOT IMMERSE THE COOKTOP IN WATER TO SOAK. THIS WILL DAMAGE THE COOKTOP.

TROUBLESHOOTING

Empty Pan Protection

| ****

ON/OFF

Flicker

| Is the pan be placed on the induction cooker? Or is it an induction compatible pan?
Low Voltage Protection| E0| Check if the voltage is low
High Voltage Protection| E1| Check if the voltage is high

IGBT Overheat

| ****

E3

| Circuit board inner fan was broken or the air inlet is blocked.
Coil Sensor Open Circuit or Short Circuit| E5| Check if the coil temperature sensor cable was broken, or the plug is unplug.
IGBT Sensor Open Circuit or Short Circuit| E7| Check if the IGBT sensor or relevant circuit was broken
Circuit failure| EC| Check the circuit board if the components are damage.

SPECIFICATIONS

Model| SR-18AR/ SR-18BR/ SR-18CR| SR-34AR/ SR-34BR/ SR-34CR| ****

SR-65AR

| SR-34AWR/ SR-34BWR
---|---|---|---|---
Voltage| 110-120V

~60Hz

| 220-240V

~60Hz

| 220-240V

~60Hz

| 220-240V

~60Hz

Consumption| 1800W| 3400W| 2600W| 3400W
Current| 16A| 15A| 12A| 15A
Dimension| 12.60” x 13.4” x 3.94” (H)
Net Weight| 13.45 LBS
Power Range| 430W~

1800W

| 1500W~

3400W

| 1100W~

2600W

| 1500W~

3400W

Cord Length| 4.4 feet
Protection Designs| Overheat protection.Automatic hazard detection.Circuit protection sensor.High voltage.20A fuse.Small object heat prevention.Thermostat.

Pan material detec  on

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for consumer ISM equipment.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.

This device complies with part 18 of the FCC rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Your Guarantee

If this product is found to be faulty as a result of faulty materials or workmanship within one year from date of purchase, it will be repaired free of charge.
This guarantee is subject to the following terms:

• Sunpentown must be no fied of the fault.
• Proof of purchase must be presented to Sunpentown’s nominated representative
• The warranty will be void if the product if modified, misused, or repaired by an unauthorized person.
• The warranty after repair will not be extended beyond the original one-year period.
• All replacement parts will be new or reconditioned.
• Parts, which are replaced, become the property of Sunpentown.
• The warranty applies for the use of the product in the USA only.

What is NOT COVERED:

• Warranty does not include freight charges.
• Incidental or consequential damage caused by possible defects with this product.
• Damage to the product caused by improper power supply voltage, accident,fire, floods or acts of nature.
• Failure of product resulting from unauthorized modifications to the product.
• Improper installation or failure to perform the necessary maintenance.

This GUARANTEE is in addi on to your Statutory Rights
SUNPENTOWN INTERNATIONAL INC.
14625 Clark Ave. City of Industry, CA 91745
Tel: 800-330-0388
[email protected]
www.sunpentown.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>