Shelly Plus 1PM WiFi Wlan Switching Actuator User Guide
- June 6, 2024
- Shelly
Table of Contents
Shelly Plus 1PM WiFi Wlan Switching Actuator
Shelly Plus 1PM
This document contains important technical and safety information about the device and its safety use and installation. Before beginning the installation, please read this guide and any other documents accompanying the device carefully and completely. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of the law or refusal of legal and/or commercial guarantee (if any). Allterco Robotics is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.
Introduction to Shelly
Shelly® is a line of innovative Devices, which allow remote control of
electric appliances through a mobile phone, tablet, PC, or home automation
system. Shelly® may work standalone on the local WiFi network, without being
managed by a home automation controller, or it can also work through cloud
home automation services. Shelly® devices can be accessed, controlled, and
monitored remotely from any place the User has Internet connectivity, as long
as the devices are connected to a WiFi router and the Internet. Shelly® has an
integrated web server, through which the User may adjust, control and monitor
the Device. The cloud function could be used, if it is activated through the
web server of the Device or the settings in the Shelly Cloud mobile
application. The User can register and access Shelly Cloud using either
Android or iOS mobile application, or with any internet browser at
https://my.shelly.cloud/
Shelly® Devices have two WiFi modes – Access Point (AP) and Client mode (CM).
To operate in Client Mode, a WiFi router must be located within the range of
the Device. Devices can communicate directly with other WiFi devices through
HTTP protocol. An API can be provided by the Manufacturer.
CAUTION! Before beginning the installation please read the accompanying
documentation carefully and completely. Failure to follow recommended
procedures could lead to malfunction, danger to your life or violation of the
law. Allterco Robotics is not responsible for any loss or damage in case of
incorrect installation or operation of this Device.
Legend
- N – Neutral input (Zero)
- L – Line input (110-240V)
- O – Output
- SW – Switch (input) controlling O
Installation Instructions
CAUTION! Danger of electrocution. The mounting/installation of the Device
should be done by a qualified person (electrician).
CAUTION! Do not connect the Device to appliances exceeding the given max
load!
CAUTION! Connect the Device only in the way shown in these instructions.
Any other method could cause damage and/or injury.
CAUTION! Use the Device only with a power grid and appliances which
comply with all applicable regulations. short circuit in the power grid or any
appliance connected to the Device may damage the Device.
RECOMMENDATION! he Device may be connected to and may control electric
circuits and appliances only if they comply with the respective standards and
safety norms.
RECOMMENDATION! The Device may be connected with solid single-core cables
with increased heat resistance to insulation not less than PVC T105°C.
Before installing/mounting the Device ensure that the grid is powered off
(turned down breakers). Connect the Relay to the power grid and install it in
the console behind the switch/power socket following the scheme that suites
the desired purpose: Connecting to the power grid with power supply 110-240V
AC (fig. 1) or 24-240V DC Connecting to the power grid (fig.2).
without power metering
The WiFi Relay Switch Shelly® Plus 1PM may control 1 electrical circuit up to
3.5 kW. It is intended to be mounted into a standard in-wall console, behind
power sockets and light switches or other places with limited space. Shelly
may work as a standalone Device or as an accessory to another home automation
controller.
For inductive appliances, those that cause voltage spikes during switching on:
electrical motors, as fans, vacuum cleaners and similar ones, RC snubber
(0.1µF / 100 / 1/2W / 600V AC) should be wired between Output and Neutral of
the circuit. Before starting, wire check that the breakers are turned off and
there is no voltage on their terminals. This can be done with a phase meter or
multimeter. When you are sure that there is no voltage, you can start wiring
the cables according to fig.1. Install a wire from “O” to the load and from
the load to the Neutral. Install also a wire from the Fuse to “L”.
Connect the Neutral to the device.The last step is to install a cable from the
switch to the terminal SW. For more information, please visit: http
://shelly-api-docs.shelly.cloud/#shelly-family-overview or contact us at:
developers@shelly.cloud
Specification
- Max load: 16A/240V
- Working temperature: 0°C up to 40°C
- Radio signal power: 1mW
- Radio protocol: WiFi 802.11 b/g/n
- Frequency: 2412-2472 Hz; (Max. 2483.5MHz)
- Operational range (depending on local construction): – up to 50 m outdoors, up to 30 m indoors
- Dimensions (HxWxL): 41x36x17 mm
- Electrical consumption: < 1 W
- Mounting: Wall box
- Wi-Fi: YES · Bluetooth: v4.2
- Basic/EDR: YES
- Bluetooth modulation: GFSK, /4-DQPSK, 8-DPSK
- Bluetooth frequency TX/RX – 2402 – 2480MHz
- Temperature Protection: YES
- Scripting (mjs): YES
- HomeKit support: YES
- MQTT: YES · URL Actions: 20
- Scheduling: 50
- AC power supply: 110-240 V
- DC Power supply: 24-240 V
- CPU: ESP32 · Flash: 4MB
Technical Information
- Control through WiFi from a mobile phone, PC, automation system or any other Device supporting HTTP and/or UDP protocol.
- Microprocessor management.
- Controlled elements: 1 electrical circuits/appliances.
- Controlling elements: 1 relays.
- Shelly may be controlled by an external button/switch.
CAUTION! Danger of electrocution. Mounting the Device to the power grid
has to be performed with caution.
CAUTION! Do not allow children to play with the button/ switch connected
to the Device. Keep the Devices for remote control of Shelly (mobile phones,
tablets, PCs) away from children.
INITIAL INCLUSION
You may choose if you want to use Shelly with the Shelly Cloud mobile application and Shelly Cloud service. Instructions on how to connect your device to the Cloud and control it through the Shellly App can be found in the “App guide”. You can also familiarize yourself with the instructions for Management and Control through the embedded Web interface.
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly
Plus 1PM is in compliance with Directive 2014/53/ EU, 2014/35/EU, 2014/30/EU,
2011/65/EU. The full text of the EU declaration of conformity is available at
the following internet address https://shelly.cloud/knowledge-base/devices
/shelly-plus-1pm
Manufacturer: Allterco Robotics EOOD
Address: Bulgaria, Sofia, 1407, 103 Cherni vrah Blvd.
Tel.: +359 2 988 7435
E-mail:support@shelly.cloud
Web:http://www.shelly.cloud
Changes in the contact data are published by the Manufacturer at the official
website of the Device http://www.shelly.cloud
All rights to trademarks She® and Shelly®, and other intellectual rights
associated with this Device belong to Allterco Robotics EOOD.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>