Cal Comp Electronics Communications W0DR1500F2 WLAN Module User Manual
- June 6, 2024
- Cal Comp Electronics Communications
Table of Contents
Product name: WLAN Module
Model number: W0DR1500F2
Brand name: Cal‐Comp
Manufacturer: Cal‐Comp Electronics & Communications Co., Ltd.
General Description
This document is to specify the product requirements for the 802.11 b/g/n SDIO
Module. This Module is based on Realtek RTL8189FTV-VB-CG chipset that complied
with IEEE 802.11g, IEEE 802.11b, IEEE 802.11n standard from 2.4G2.5GHz, and it
can be used to provide up to 54Mbps for 802.11g,11Mbps for 802.11b, and
150Mbps for 802.11n to connect your wireless LAN.
With seamless roaming, fully interoperability, and advanced security with WEP
standard,802.11b/g/n Module offers absolute interoperability with different
vendors 802.11 b, 802.11 g, 802.11n
Access Points through the wireless LAN.
This module has been tested and found to comply with the following
requirements for Modular Approval.
Part 15.247 – Operation within the bands 2400-2483.5MHz.
Test Modes
This device uses various tests mode programs for test set up which operate separately from production firmware. Host integrators should contact the grantee for assistance with test modes needed for module/host compliance test requirements.
Antenna information
| Antenna Type | Antenna Part No. | Freq. (MHz) |
|---|---|---|
| PCB W0DR1500F2 | B W0DR1500F2 | 2.4G |
Features
- Compatible with IEEE 802.11b stand
- Compatible with IEEE 802.11b standard to provide wireless 11Mbps data rate
- Compatible with IEEE 802.11g standard to provide wireless 54Mbps data rate
- Compatible with IEEE 802.11n standard to provide wireless 150Mbps data rate
- Operation at 2.4G-2.5GHz frequency band to meet worldwide regulations
- Supports WEP, WPA, WPA2, TKIP, AES enhanced security
- Drivers support Windows, Linux, Android
- SDIO interface
- RoHS compliant
Electrical and Thermal Characteristics
- Temperature Limit Ratings
| Parameter | Minimum | Maximum |
|---|---|---|
| Storage Temperature | -40℃ | +80℃ |
| Operating ambient Temperature | 0℃ | +70℃ |
| Junction Temperature | 0℃ | +125℃ |
- General Section
| Detailed | Description |
|---|---|
| Antenna Type | PCB ANT |
| Operating Voltage | 3.3V±10% |
| Form Factor and Interface SD | SDIO2.0 |
- Software
| Driver security | Windows,Linux, Android |
|---|---|
| Security | WEP,WPA,WPA2,TKIP,AES |
- Recommended operation conditions for module
| Symbol | Rating | Min | Typ | Max | units |
|---|---|---|---|---|---|
| VDD33/VDDIO | DIO 3.3V | 3 | 3.3 | 3.6 | V |
Warning
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference and
- this device must accept any interference received, including interference that may cause undesired operation.
Federal Communications Commission (FCC) Statement 15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Label
FCC ID: 2AA2U-W0DR1500F2
Required End Product Labeling
Any device incorporating this module must include an external, visible, permanent marking or label which states: “Contains FCC ID: 2AA2UW0DR1500F2”
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>