wansview K3 HD Wireless IP Camera User Manual
- June 6, 2024
- Wansview
Table of Contents
- Download the App (Android and 10S)
- What’s in the box?
- connections
- Power on Camera
- Connect Phone with 2.4G WiFi
- Add Camera and Connect WiFi
- Live Video Interface
- How to connect the camera to the second Phone?
- Change password and add another user
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
wansview K3 HD Wireless IP Camera
K3(1080P)/K2(720P) User Manual
We keep improving the app if the app interface is not in accordance with the
instructions. please go to wansviow website: http://www.wansview.com for the
latest instructions.
www.wansview.com
Download the App (Android and 10S)
Go to the App Store or Google Play to search and download the “Wansview” APP to your supported device Or scan the QR code below to get the app.
| |
---|---|---
| |
What’s in the box?
- 1 Installation guide
- 1 Power adapter
- 1 Camera
- Mounting accessories
connections
-x- Status LED Solid Light Blinking Slowly Blinking Quickly
Indicator Light Status | Device Status |
---|---|
Red light is blinking slowly | Power up and activating |
Red and blue lights are blinking slowly | The device is ready to connect |
Blue light is blinking quickly | The device is receiving the wifi signal or |
connecting to the wifi
Blue and red lights are solid and steady| The device is connected to the
network
Red light is blinking quickly| The device is restored to factory default
The blue light goes off| The device failed to connect to the network
Power on Camera
Please make sure the camera is in the same room, close to the router, before performing the setup. Then, using the included power supply, connect to Power.
Tips: You can relocate it to where you want after it is all set up. You just unplug it and move it to the new location and plug it in, the camera will connect to your WiFi automatically, no need to set it up again. But please make sure the new location will not be far from your router.
Connect Phone with 2.4G WiFi
Connect your mobile phone with 2.4G WiFi. (5G is not supported for the camera)If you are using a dual-band router, make sure your 2.4G WiFi name is different from your 5Gone.
Add Camera and Connect WiFi
1.Select [Add IP Camera], and tap **+**
to add camera| 2. Select [Add
cameras via| 3. Scan the QR code on the WiFi mode] back of the camera
---|---|---
4. Hold the “Reset” button for about 3-5 seconds until you see the blue light
is on| 5. Name the camera, then [Next]| 6. Input your WiFi password and
click on[Connect to WiFi]
---|---|---
7. Use the camera to Scan the QR Code, Click on [Blue light has quickly
flashed] when the blue light flashes quickly| 8. When the camera receives a
WiFi signal, it will sound 2 beeps| 9. You should see it says online.
Congratulations! Your camera is all set up. Click on the image to enjoy
viewing and controlling it now
---|---|---
Live Video Interface
****Menu | **** Unavailable | Snapshot to phone | Contrast |
---|---|---|---|
IR ON | Mirror | Record video to phone | Brightness |
IR OFF | Flip | Listen on/off | Restore to default |
⇔ Unavailable | Exit | Talk on/off | 1080P/480P |
How to connect the camera to the second Phone?
Wansview camera supports 4 devices to view the same camera at the same time.
After you use one phone to get your camera connected to your WiFi and you can
view the live video from your first phone. If you would like to add your
camera to the second phone, please follow the below steps: 1: Download the
Wansview App to the second phone 2: Launch the Wansview app, and tap “ **+**
“and select “Add already connected network camera”.
Users can use the below ways to add the camera: 1) Lan Search If the mobile
device and the camera are in the same WiFi network, the user can use “Lan
Search” to search the connected camera.
2) Scan QR code If the camera is on your hand, you can tap to scan the
Camera’s QR code to get the camera information.
- Manually input camera information Camera’s DID can be found from the camera’s sticker or Wansview app, default username/Password is admin/123456; Name can be any information. Attention: please remember to give your camera a name, and input your Password. Click on IV, Igo back to home to start to view & control.
Change password and add another user
When the camera is “online” , click on “IV to access “Advanced Setting”, Under the User Setting/Management, the user can change the default username(admin) and password (123456), or create another user account with certain access rights, such as an Operator or Viewer account for another person to view the camera.
Change Username and password
Tap User Setting, and choose Administrator>Admin, user can change the user
name and password, then tap 2)
Add another user account
On User Setting, tap; 3 to add user, manually add the user name and password,
then choose the Role(Operator or Viewer). Administrator: Full access rights
Operator: Can operate on the camera live video screen, but not access to other
settings like Alarm setting, Advanced Setting, etc.
Viewer: only can view camera, no more operations on the camera video
screen.
Note : Password shall be no longer than 20 characters.
Trouble Shooting Frequently Asked Questions
1. If you have several cameras, please follow the below steps to use the
Multi-view function.
Tap More on the Menu, then choose Multi-View
2. How do I change my video stream resolution? Click on icon 480P to change
the resolution.
3: Night vision doesn’t work If the night vision stops working, please turn on
the IR light as below
4. How to restore to factory default Push down the “Reset” button around
15-20 seconds until the red light flashes quickly and you will hear a beep,
then the camera will be back to factory default. After restore, please set up
the camera using the default user name (admin) and password(123456).
5. I want to add the camera to other software/app, which URL should I use?
RTSP Stream: rtsp://IP:rtsp port
/live/ch0 (default RTSP port: 554)
MJEPG Stream: http://ip:port/mjpeg/stream.cgi?chn=0
Snapshot: IP:port/jpeg/snap.CGI?chn=0
6. Why can’t I access the camera remotely with Wansview App when I am
outside?
If your phone is using cellular data, please check if Wansiew App has
permission of cellular data usage on your phone or not. If your phone is on
another available WiFi network, you still can’t access the camera remotely,
the problem might be the firewall of your home router which blocks outside
network to access the camera. Please follow the below instruction to turn the
router’s firewall off to allow an outside network to access the camera:
Connect your phone to home WiFi—go to Wireless setting of your phone, you can
know router’s IP address—input the IP address to the browser on your
phone—input router’s username and password then you can log in your
router—find option “Firewall”—you can turn it off. Or you can access your home
router on your computer, the link for your reference:?
https://www.wikihow.com/Access-a-Router
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>