SACKit 1010384 WOOFit S Bluetooth Speaker User Manual
- June 6, 2024
- SACKit
Table of Contents
SACKit 1010384 WOOFit S Bluetooth Speaker
Thank you!
Thank you for purchasing this WOOFit S speaker from SACKit. Please read this manual carefully before use. We are not responsible for any personal or property damage caused by the improper use of this product. We hope you enjoy the louder, richer sound, and features from your WOOFit D device. Please save this user manual for later supervision and guidance securing the correct use of the product. Embrace life with your new SACKit product!
Box Contents
- WOOFit S speaker
- User manual
- 2-in-1 charging cable
Remember
Remember to register your new SACKit product on our website: www.SACKit.eu/reg
Quick Start Guide
- Charge the WOOFit S Speaker using the included micro USB charging cable for no less than 2 hours
- Turn on WOOFit S
- Turn on Bluetooth on the device you wish to connect to
- Choose WOOFit S in the Bluetooth settings on your device
- Start playing music from your device
- Enjoy the music and dance
- Micro USB input/AUX-in
- Mini-jack input
- AUX out
- Micro SD player
- Power button
- Light indicator
- Microphone
- M (Mode) button
- Play/Pause button
- Volume (-) button/Previous track
- Volume (+) button/Next track
Buttons
Power button This button must be slid right to turn on the WOOFit S
speaker, and to the left to turn the device off.
M (mode) knap Push the Mode button to switch between micro AUX-IN and
Bluetooth mode. If there is no Micro SD card in the WOOFit S speaker, this
mode will automatically be skipped.
Play/Pause When the device is in Bluetooth mode a push on the Play/Pause
button will either play or pause the music.
Volume buttons (-/ +) These buttons make it possible to adjust the
volume. When WOOFit S is in Bluetooth mode you will hear a ”beep” sound when
the sound level reaches maximum. This warning sound will not occur when the
speaker is in AUX OUT or AUX-IN mode.
Charging
To charge the WOOFit S speaker, the included Micro USB charging cable must be inserted in the Micro USB input on WOOFit S and be connected to a computer or an adapter. The charging begins automatically whether the system is on or off. The charging status can be seen on the light indicator. During charging the light indicator will light up red. When the battery is fully charged the light indicator will turn off. A full charge of WOOFit S takes approximately two hours.
Connections
Bluetooth
- WOOFit S is turned on by sliding the power button to the right. When the light indicator alternately flashed blue and red, WOOFit S is ready for pairing with the desired device. Please notice that pairing mode automatically will void after 5 minutes if not paired. If this happens, the WOOFit S speaker will have to be restarted.
- Perform the connection procedure on your Bluetooth device to find the WOOFit S speaker. This system is indicated as ”WOOFit S”. If ”WOOFit S” does not appear on the list of found devices, the connection process must be started over. Note that the two units should be in the one-meter range of each other during the connection.
- Choose the ”WOOFit S” connection on your Bluetooth device.
- When the connection is established the light indicator will flash slowly in the color blue. Next time the WOOFit S speaker gets turned on, a connection will automatically be made with the last paired device.
- Notice: If passcode* input is demanded on your Bluetooth device enter ”0000”. The passcode may also appear under the synonyms as; ” Passkey ”, ”Pin Number” or ”Password”
Phone call
If music is playing when in Bluetooth mode and you have an incoming call, WOOFit S will automatically switch to hands-free mode. Press the Play/Pause button to accept the call. To hang up press the Play/Pause button again. Two short pushes on the Play/Pause button will make WOOFit S redial.
AUX connection Press one time on the Mode button to choose ”AUX IN” mode.
The Light indicator will now light up green. To adjust the sound level the
volume buttons -/+ has to be pressed and held down. You will not be able to
use -/+ buttons for the previous track or next track when playing from this
AUX mode. Use the play/pause button to play or pause.
Mini-jack input This input lets you connect headphones to WOOFit S. When
the headphones are connected, the sound from the speaker will stop and you can
enjoy music from your headphones only.
Micro USB input This input is used for charging with the included Micro
USB charging cable. This input can also be used for playing music from your
computer via jack input. Use this input to read the content of the Micro SD
card from your computer.
Micro SD player This input enables the feature to play your music
directly from a Micro SD card. Insert the Micro SD card and WOOFit S will
automatically start playing music from the SD card no matter what mode the
speaker is in. The light indicator will slowly flash green to indicate the
correct mode. The sound level is adjusted by holding down the volume buttons.
One short press on the volume buttons will work as the previous track/next
track in this mode.
Home Systems It is possible to connect WOOFit S to a home system. To do
this, use a standard stereo mini-jack (3.5 mm.).
Stereo pair You can connect two WOOFit S speakers as a stereo pair. Make
sure both speakers are NOT connected to any devices. Then hold down the mode
button (M) on one of the speakers until they connect to each other. The
speakers will remember stereo parring even after they have been turned off.
Light Indicator
- No light: WOOFit S speaker is turned off or fully charged.
- Greenlight: WOOFit S is turned on.
- Green flash slowly: Micro SD Player is active.
- Red and blue flash: WOOFit S is searching for a Bluetooth device.
- Red light: WOOFit S is charging.
- Green and blue flash: The connection between WOOFit S and Bluetooth device has failed.
- Green and blue flash slowly: Music is playing from a Bluetooth device.
Troubleshooting
Connection problems WOOFit S Bluetooth will lock on to the last connected device, which requires the connection to be disconnected before a new unit to be connected to WOOFit S. This can be done on the connected device (in Bluetooth settings) or by resetting the speaker. WOOFit S speaker is reset by holding the mode button down for 3 seconds and disconnecting the Bluetooth signal. The speaker is now ready to connect with a new Bluetooth device.
Audio quality problems If the audio quality is poor, a reason might be
low battery level. Therefore always try to fully charge WOOFit S to secure the
absolute best audio quality.
Warning To prevent damage, fire, or electric shock, it is strictly
forbidden to remove or replace parts of the unit. Always consult a
professional workshop or a qualified service center if the unit has been
damaged.
Safety Precautions
Please read and follow these instructions to ensure correct and safe use of the WOOFit S loudspeaker. Charge WOOFit S a minimum of 2 hours using the supplied USB cable before you use the speaker for the first time. Do not expose WOOFit S to rain, water or store it in humid environments. Do not place WOOFit S in or near any sort of liquids. Do not place WOOFit S in or near sources of fire. (E.g.: Candles, fireplaces, or other places with open fire.) Avoid placing WOOFit Son surfaces that are hot, dusty, or emit vibrations. WOOFit S must only be placed on stable, flat, and horizontal surfaces. Do not place objects on top of WOOFit S. Do not use excessive force or violence when operating the speaker buttons. Use and store only the USB cable properly and safely, both during and after use. If cleaning of the speaker is needed, use only a dry, clean and soft cloth without corrosive solvents or detergents.
Technical Specifications
- Operation Voltage: 3.7 V
- Charging Voltage: 5V
- Output Power: 3 W
- Speaker Spec.: 40 mm 4 Ω 3 W
- Frequency Response: 18Hz – 20 KHz
- Lithium Battery Capacity: 400 mA/H THD: ≤ 0.5%
- SNR: ≥ 95 dB
- Dimensions: D: 60 mm. H: 54 mm.
Notice
The battery level of WOOFit S will only show on iPhone and iPad devices. Other Bluetooth devices will not provide information on the battery level. Bluetooth connection has first priority, so when you play music from another Bluetooth device the audio from another mode (AUX IN or Micro SD Player) stops. When you stop playing from a Bluetooth device, WOOFit S automatically returns to the previous mode after 3 seconds. www.SACKit.eu
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>