GEPRC Naked GoPro Hero 8 Camera User Manual
- June 6, 2024
- GEPRC
Table of Contents
GEP GoPro Hero 8 Naked
USER MANUAL
GoPro8 Naked
Summary
GoPro hero 8 Naked, specially designed by GEP team for quadcopter, finally meets you. The newly designed BEC is perfect for GoPro 8. Support 2-6s voltage input and output 5V@2A. It is equipped with POWER/MODE and REC button, and has a quick detachable GH1.25-3P connector to support remote control.
Features
- It’s specially designed for quadcopter, and its ultra light weight is only 25.7g
- 4K@60fps,4K@30fps,2.7K@50fps Recording
- Scan preset QR code switch settings
- BEC board input voltage 2S-6S,output5V-2A
- Integrated GoPro POWER/MODE button and REC button, operation quickly and conveniently.
- GH1.25-3P connector is used to connect flight control and realize remote control
- UV protection lens to protect the camera
- Nd16 filter to reduce the light input of camera sensor
Specification
Model: Naked GoPro Hero 8 Camera
Dimension: 604022.5mm
Weight: 25.7g
Input: 2-6S
Output: 5V2A
Memory: SD Card
Connector:GH 1.25 3PIN
Indicator status
Connect GH1.25 Control cable with camera and input 2-6s power.LED will flash 1 times, BEC plate power light is always on(green light).
Instructions | Operation | Indicator |
---|---|---|
Power on | Press the power/mode switch once | Flash 3 times, off |
Power off | Press and hold the power/mode switch for 5seconds | Flash 7 times, |
off
Start recording| Press the record switch once| Flash slowly
Stop recording| Press the record switch once| Flash 3 times, off
Switch mode| Press the power/mode switch once| NONE
QR code switching recording settings| Scan preset QR code| Flash 2 times, off
GEP GoPro Hero 8 Naked
BEC Board Diagram & Set Guide
Recording with transmitter
-
Weld control cable to FC(F411-AIO)
♦ RED wire→ positive pole
♦ BLACK wire→ negative pole
♦ YELLOW wire→LED -
Connect FC to BETAFLIGHT,enter the following command on the command wire,save.
resource LED_STRIP 1 NONE
resource PINIO 1 A08
set pinio_box = 40,255,255,255
Save -
Turn on the USER1 mode under the mode option,add range to Transmitter idke switch.
-
Turn the BEC power switch to left,connect the control cable.
-
Supply power to FC, GoPro8 Naked will auto start. Operation remote control AUX4 switch, move the cursor from the white area to the yellow area and back to the white area to start the recording. Repeat the operation again to end the recording.
Notes: GEPRC-F722-AIO and F411-AIO have the same wiring but different codes, as follows:
resource LED_STRIP 1 NONE
resource PINIO 1 A01
set pinio_box = 40,255,255,255
Save
Wire Diagram
BEC board retains the welding pad,so you can by wiring to connect the camera main board.There is the wiring diagram:
Turn on WiFi and connect APP
- Open GoPro Quick APP, and search camera .
- Turn on Naked GoPro Hero8 And scan the QR code below,The red indicator will flash twice, and then press the video button three times, the Naked GoPro Hero 8 will enter the connection state.
- Connect the WiFi of Naked GoPro Hero 8 according to the prompt of GoPro quick app.
Connect:
Website: https://geprc.com/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>