Mark bass BAS0011938-000 Little Mark Amp 1000 Vintage Owner’s Manual
- June 6, 2024
- Mark bass
Table of Contents
V.01.July.2021
OWNER’S MANUAL
Little Mark Vintage Amp 1000
IMPORTANT SAFETY INSTRUCTIONS
- Read these instructions;
- Keep these instructions;
- Heed all warnings;
- Follow all instructions;
- Do not use this apparatus near water;
- Clean only with a dry cloth;
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions;
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat;
- Do not defeat the safety purpose of the polarized or ground-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet;
- Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus
- Only use attachments/accessories specified by the manufacturer; ****
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from the tip-over (and Fig 21 DU Tipping Cart Symbol).
- Unplug this apparatus during lightning storms or when unused for long periods of time;
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped;
- “WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE, AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS”.
- TO COMPLETELY DISCONNECT THIS APPARATUS FROM THE AC MAINS, DISCONNECT THE POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE;
- THE MAIN PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY ACCESSIBLE.
- In the case of voltage, the selector makes sure the switch on the rear panel is on the correct voltage before connecting it to the AC power, and the fuse is the right value for that voltage (This selector is not available on the 100V version). Please change the voltage/fuse values label located near the voltage selector matching the voltage/fuse values when you need to change the voltage of the apparatus.
- “WARNING: THIS APPARATUS MUST BE SECURELY ATTACHED TO THE FLOOR OR WALL IN ACCORDANCE WITH INSTALLATION INSTRUCTIONS. TIPPING, SHAKING, OR ROCKING THE MACHINE MAY CAUSE INJURY OR DEATH.”
- “CAUTION: THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN TEH OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO”
- TAKE CARE WHEN LIFTING
MORE INFORMATION
For warranty and service information, please contact your local Markbass
distributor (contact information available at
www.markbass.it)). For more technical information,
please visit us at www.markbass.it and fill out the
form on the Support page. We hope you enjoy your power amp and use it to make
great music!
“The Lightning Flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product enclosure that may be of sufficient
magnitude to constitute a risk of shock to persons.”
“The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.”
“To be used only with altitude not exceeding 2000 m”
“To be used only where the climate is not tropical”
The LITTLE MARK VINTAGE AMP 1000 is part of our Vintage series lineup, state-of-the-art products that mark a new era at Markbass. This 1000W power amp is warm, defined, and clear even at full volume. With this much power at your disposal, and the new big-band limiter built-in, you can play across a wide dynamic range and even handle high signal peaks without clipping. It’s a perfect match for the amazing MARK VINTAGE PRE or any other bass preamp. Clear and consistently reliable, while being ultra- lightweight and super portable.
TECHNICAL SPECS
| INPUTS | INPUT: | 1 Mohm – 5Vp (Jack Mono) |
|---|---|---|
| CONTROLS | MASTER VOLUME LIMITER | (from 0 to MAX) |
| OUTPUTS | SPEAKER OUT: | Speakon |
| OTHERS | BI-BAND LIMITER |
WEIGHT:
WIDTH:
DEPTH:
HEIGHT:
OUTPUT POWER:
POWER REQUIREMENT:| 6.04 lbs / 2,74 kg 10.87″/ 27.6 cm 9.84″/ 25 cm 3.27″ /
8.3 cm 1000W RMS @ 4 ohms / 600W RMS @ 8 ohms 100/120V; 230V; 240V – 50/60Hz
(Voltage is factory preset according to the region of sale)
WARNING:
The LITTLE MARK VINTAGE AMP 1000 is manufactured to be used in the country
where they have been sold, and they are factory preset to that country’s
voltage. So make sure you’re sending the correct voltage to your amp before
you connect it to the AC power. Due to homologation issues, the voltage may
not be changed. The minimum ohm load for all Markbass heads/amps is 4 ohms.
NOTE1: Equipment for professional use.
NOTE2: Product specifications are subject to change without notice.
FUSES: LITTLE MARK VINTAGE AMP 1000
T 12A 250V for 100V setting;
T 10A 250V for 120V setting;
T 8A 250V for 230V/240V setting
LITTLE MARK VINTAGE AMP 1000
Product specifications are subject to change without notice
Italy – 66020 San Giovanni Teatino (Ch) – Via Po, 52
Tel. +39 085 446 3755
Fax +39 085 440 7764
www.markbass.it
– info@markbass.it
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>