Mark bass LITTLE AG 1000 Andrew Gouche 1,000W Bass Amplifier Head Black Owner’s Manual
- June 13, 2024
- Mark bass
Table of Contents
V.21.July.2022
OWNER’S MANUAL
LITTLE AG 1000
IMPORTANT SAFETY INSTRUCTIONS
-
Read these instructions;
-
Keep these instructions;
-
Heed all warnings;
-
Follow all instructions;
-
Do not use this apparatus near water;
-
Clean only with dry cloth;
-
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions;
-
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat;
-
Do not defeat the safety purpose of the polarized or ground-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet; -
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus
-
Only use attachments/accessories specified by the manufacturer;
-
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from the tip-over (and Fig 21 DU Tipping Cart Symbol). -
Unplug this apparatus during lightning storms or when unused for long periods of time;
-
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped;
-
“WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS”.
-
TO COMPLETELY DISCONNECT THIS APPARATUS FROM THE AC MAINS, DISCONNECT THE POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE;
-
THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REAMIN READILY ACCESSIBLE.
-
In case of voltage selector make sure the switch on the rear panel is on the correct voltage before connecting it to the AC power, and the fuse is the right value for that voltage (This selector is not available on the 100V version). Please change the voltage/fuse values label located near the voltage selector matching the voltage/fuse values when you need to change the voltage of the apparatus.
-
“WARNING: THIS APPARATUS MUST BE SECURELY ATTACHED TO THE FLOOR OR WALL IN ACCORDANCE WITH INSTALLATION ISTRUCTION. TIPPING, SHAKING, OR ROCKING THE MACHINE MAY CAUSE INJURY OR DEATH.”
-
“CAUTION: THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN TEH OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO”
MORE INFORMATION
For warranty and service information, please contact your local Mark bass
distributor (contact information available at
www.markbass.it). For more technical information,
please visit us at www.markbass.it and fill out the
form on the Support page. We hope you enjoy your power amp and use it to make
great music!
“The Lightning Flash with arrowhead symbol within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product enclosure that ma to constitute a risk
of shock to persons.”
“The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.”
“To be used only with altitude not exceeding 2000 m”
“To be used only where the climate is not tropical”
TECHNICAL SPECS
INPUTS
INPUT: Impedance 500 Kohm/ maximum voltage 9 Vpp
EFFECT RETURN: Impedance 33 Kohm/ maximum voltage 10Vpp
CONTROLS
| INPUTS | INPUT: | Impedance 500 Kohm/ maximum voltage 9 Vpp |
|---|---|---|
| EFFECT RETURN: | Impedance 33 Kohm/ maximum voltage 10Vpp | |
| CONTROLS | GAIN: | -46 to 23dB range |
MASTER VOLUME
LINE OUT LEVEL
LIMITER (from 0 to MAX)
MUTE switch
GROUND LIFT
PRE/POST EQ FSW| (switch on rear panel)
(switch on rear panel)
input for (optional) footswitch to turn on/o EQ and MUTE
EQ| ULTRALOW:| level ±16 dB (freq. 65 Hz)
LOW:| level ±16 dB (freq. 100 Hz)
MID:| level ±16 dB (freq. 500 Hz)
HIGH MID:| level ±16 dB (freq. 1.4 KHz)
HIGH:| level ±16 dB (freq. 3.8 KHz)
OUTPUTS| LINE OUT:| balanced XLR, maximum voltage 20 Vpp
EFFECT SEND:| unbalanced, max voltage 20Vpp (pre EQ)
TUNER OUT:| unbalanced, max voltage 2Vpp
SPEAKER OUT:| one speakon speaker out
(minimum impedance load for the amp is 4 ohm)
OTHERS| WEIGHT:| 7.05 lbs/ 3.2 kg
WIDTH:| 10.87”/ 27.6 cm
DEPTH:| 9.84”/ 25 cm
HEIGHT:| 3.27” / 8.3 cm
OUTPUT POWER:| 1000W RMS @ 4 ohm / 600W RMS @ 8 ohm
---|---
POWER REQUIREMENT:| 100V; 120V; 230V; 240V – 50/60Hz
(Voltage is factory preset according to region of sale).
Minimum ohm load for all Markbass heads is 4 ohms.
Mark bass amps/combos are manufactured to be sold and used in the country of
purchase, and are factory preset to that country’s voltage. Due to
homologation issues, the voltage may not be changed.
Rack ears do not come included with this head.
NOTE1: Equipment for professional use.
NOTE2: Product specifications are subject to change without notice.
FUSES: LITTLE MARCUS II 1000
T 12A 250V for 100V setting;
T 10A 250V for 120V setting;
T 8A 250V for 230V/240V setting
Product Specifications are subject to change without notice
Italy – 66020 San Giovanni Teatino (Ch) – Via Po, 52 – Tel. +39 085 446 3755 –
Fax +39 085 440 7764 –
www.markbass.it –
info@markbass.it
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>