KIND LED X2 Professional LED Grow Light User Guide
- June 11, 2024
- KIND LED
Table of Contents
KIND LED X2 Professional LED Grow Light
CONGRATULATIONS ON PURCHASING THE MOST ADVANCED LED GROW LIGHT IN THE
INDUSTRY, THE KIND LED X2
This guide will show you how to setup and use your X˜ LED ÿxture.
Please review the entire manual prior to operation.
OVERVIEW
THE KIND LED X2 COMES WITH:
- KIND LED X2 Light Fixture
- Power Cord
- RJ-14 Data Cable (x2)
- RJ-14 Dual Cable Splitter
- IP-65 Housing or RJ-14 Connection
GETTING STARTED
Your KIND LED X˜ comes fully assembled, ready to grow. Before unpacking your ÿxture, place the box ˝at on the ground, below your intended hanging location, with the top of the box facing upward.
Remove the top of the box, then remove the protective foam packaging inserts. Lower your adjustable hanging hardware (not included) to the four eyelets found on the top side of the ÿxture. Once Connected, raise the light o the desired position.
POWER CORDS AND CABLES
POWER CORDS
Your KIND LED X˜ comes with a 6ft., 240v standard power cord. For alternative
power cord recommendations please contact a KIND LED Grow Lights customer
service representative to assist in your selection.
EXTERNAL CONTROLLER CABLES
The KIND LED X˜ comes complete with a set of 7 foot RJ14 data cables and a
three way splitter. If your installation requires a longer cable, please
contact a KIND LED Grow Lights customer service representative to guide you in
the purchase of the correct cable for your needs. It is important to select
the correct cable for successful operation of your light ÿxtures.
BEST PRACTICES
ENVIRONMENT
When using the KIND LED X˜, ideal grow room temps should be around 80-85
degrees F. Any lower than this and transpiration can slow, stunting growth.
Any hotter than this and heat stress can form.
NOTE: High PPFD growing conditions require high levels of attention to detail including proper feeding and CO2 augmentation. For more please visit kindledgrowlights.com
RECOMMENDED HANGING HEIGHT
The KIND LED X˜ is designed to excel in close proximity environments but can
be used in a variety of applications.
For best practices, a minimum ÿxture height of 6” above the canopy is
recommended. The ideal recommended hang height above canopy is 12“ to maintain
the greatest intensity over the largest footprint. To maintain usable
intensity at a greater distance and larger, a maximum of 18” above the canopy
is recommended.
For applications that require less intensity such as Cloning Stages and early
Vegetative Stages, a distance from canopy greater than 18” may be suitable.
YOU ARE READY TO GROW!
For complete control of your KIND LED X˜ timing schedules, spectrum and
intensity, consider adding the optional Grow Strong GSI-1 Digital Lighting
Controller. The GSI-1 controller can operate up to 512 ÿxtures split between
two independent zones. For more information on this ÿxture and all available
options, contact a KIND LED Grow Light customer service representative at
KindLEDGrowLights.com or call (855)559–5463
SPECIFICATIONS
FCC COMPLIANCE STATEMENT
The KIND LED X˜ Commercial Lighting System has been tested at FCC-certiÿed laboratories in the United States and conforms to FCC’s Part 15B Consumer Standard for Industrial, Scientiÿc, and Medical Equipment for both conducted and radiated emissions.
Given that all electronic equipment emits some RF energy, please note that compliance with these standards does not mean a zero level of emission, only very low levels. Per
FCC requirement:
This product may cause interference to radio equipment and should not be
installed near Maritime safety communications equipment or other critical
navigation or communication equipment between 0.45-30 MHz.
This device complies with Part 15B of the FCC Rules.
Changes or modiÿcations not expressly approved by KIND LED could void the
user’s authority to operate the equipment.
Please visit www.KindLEDGrowLights.com for
a complete documentation of the KIND LED Commercial Lighting Terms of Use.
Thank You.