VDO360 VUSBEXT-U Springline USB 2.0 Extender User Manual

: June 6, 2024
: VDO360

Table of Contents

INTRODUCTION
PACKAGE CONTENTS
FEATURES：
INSTALLATION ：
Specifications ：
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VUSBEXT-U
USB 2.0 Cat. 5/6 Extender – 50M
User Manual

INTRODUCTION

This USB.2.0 Extender is capable of sending USB signals across a Cat.5 cable or higher up to 50 meters at a data rate of High Speed (480Mb/s), Full-Speed (12Mb/s), and Low Speed (1.5Mb/s). Plug the Cat 5/6 cable into the RJ-45 Connector to set up the extender. It takes only minutes to do so, and there is no configuration or drivers necessary. The USB 2.0 Extender is fully USB 2.0 compliant and it is backward compatible with USB 1.1/1.0.

PACKAGE CONTENTS

Before installation, please check the items of the package ：

Transmitter Unit
Receiver Unit
USB AM-BM cable
User Manual
Power Adapter (24V/0.5A)

FEATURES：

Supports data transfer rates of 1.5Mb/s, 12Mb/s, 480Mb/s
The product consists of two electronic modules, a “Transmitter unit” and a “Receiver unit”.
The Transmitter unit connects to a USB 2.0 Camera/Device.
Units can be connected by a standard Cat. 5 cable or higher, which can then enable the extension of USB devices up to 50m (164 feet).
Wall mounting integrated in the metal housing
Support Hot Plug & Play- no software driver is required
Power supply for Receiver unit included

Receiver Unit (connected to the PC)

Transmitter Unit (connected to the camera)

ITEM	TYPE	DESCRIPTION
1	PWR LED (Red)	LED ON power supply is connected to

Receiver unit and wall outlet.
LED OFF no power is supplied.
2| LINK LED(Green)| LED ON Indicates a valid connection between the Transmitter Unit and Receiver Unit has been established via CatS/6 cables.
LED OFF is a bad Cat 5 cable or connector
3| ACT LED(Amber)| The LED FLASHING shows the extender is linked to the PC properly & the Camera plugged into the downstream Transmitter is sending data. LED ON shows no data is being transmitted

INSTALLATION ：

Connect the Receiver Unit to the PC via USB Cable (A Male to B Male).
Plug the 24V/0.5A DC Power Supply into the USB 2.0 Extender Receiver Unit.
Plug the AC power cord of the power supply into an available electrical outlet.
Connect the USB 2.0 Extender Transmitter Unit and Receiver Unit together with
a Cat 5/6 Cable (supplied by user).
Connect USB Camera to the Transmitter Unit.
Check the LEDs on the USB 2.0 Extender Transmitter Unit. Make sure that the Act.
LED is flashing which means the extender is powered and communicating.

System Requirements ：

Windows XP/7/Vista/8/8.1/10；Mac OS

Specifications ：

Receiver Unit	Upstream Port	USB Type B Female
Downstream Port	RJ45 Jack
Power	Bus-Powered

Certifications
This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received. Including interference that may cause undesired operation.

WEEE Information
For EU (European Union) member users:
According to the WEEE Directive, do not dispose of this product as household waste or commercial waste. Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country. For information on recycling of this product, please contact your local authorities, your household waste disposal service or the shop where you purchased the product.

No part of this publication may be reproduced in any form by any means without prior written permission. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies.
Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.