Xiamen Yinxu Industry Trade WSLB Smart bulb User Manual
- June 6, 2024
- Xiamen Yinxu Industry Trade
Table of Contents
LEDEPLY Smart Bulb
User Manual
CAUTION
USE IN DRY LOCATIONS. RISK OF ELECTRIC SHOCK OR BURNS Er indoor use only
Do not Install the device with wet hands or when standing on wet of dump
surfaces,
Not for use totally half for fully enclosed luminaires, especially luminaires
with metal shade. which may distort the signal and make it harder to connect
or control the lights Do not use with Dimmers!
GET READY
i0S 10.0 & up
Android 404& up
2.4 Ghz
Download the ‘Smart Life’ App.
Register or log in if you already have an account
Add device
If the light won’t blink slowly or quickly, turn it off/on 10 times with intervals of at least 2s to reset it
**EZ MODE
AP MODE ( ONE at a time )
**
Smart bulb
FCC ID: 2AZNW-WSLB
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (a) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital Device, pursuant to part 15 of the FCC Rules. These
limits are designe to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, this grant is
applicable to only mobile configurations. The antennas used for this
transmitter must be installed to provide a separation distance of at least
20cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
Group Control
-
Tap a smart bulb in the device list to enter the ts control pared.
-
Tap the edit icon
-
Click ‘Create Group”
-
Select devices for unified management.
-
Tape ‘confirm’ to complete the setup.
Now, you can use group control to control multiple bulbs
**Alexa Settings
**
Enable the Smart Life skills in the Alexa APP, then log in your Smart Life
account, it will automatically sync your smart bulb to Alexa.
After the synchronization is successful, you can use voice commands to control
your smart bulbs.
**Google Assistant Settings
**
Tap ‘Add’ – ‘Set up device’ – ‘Have something already set up?’ – search for ‘Smart Life’ to add it and Jog in your smart life account.
Frequently Asked Questions
-
What should | do when my device fails to connect to the network?
• Check whether the router password you entered is correct.
• Ensure that broadcasting is enabled for Wi-Fi and is not hidden.
• Ensure that your device has been added over a Wi-Fi band of 2.4 GHz. Ensure that the network environment has strong and stable signals. Troubleshooting: Place your mobile phone or iPad connected to the same local area network close to the device, and open a web page to check whether the browsing is smooth and stable.
• If the network is normal but the device network connection still fails, check whether the router is overloaded. You can disable a device’s Wi-Fi feature to reserve the channel for resource reallocation.
• If wireless MAC address filtering is enabled for the router, remove your device from the router’s MAC address filtering list to ensure that it is allowed to connect to the network. You can also disable MAC address filtering.
If your device still fails to connect to the network after the preceding steps, please contact ledeply@gmail.com to let us troubleshoot this issue -
The light changed from flashing to regular, but it still fails to connect?
• Please check if the Wi-Fi password you entered during network configuration is correct.
• Please keep the distance to the router during the network configuration (within 1 ~ 5 meters, there must be no metal spacers in the middle)
• The smart device that your router’s CPU can load has reached the upper limit. Please disconnect some devices and try again.
• The device does not reset after the network configuration fails. You can try the network configuration again after the device is reset. -
My smart bulb was disconnected, how can | reset it?
EZ Mode:
• Make sure the device is powered off for more than 10 seconds before powering on the device.
• Turn on and off ten times (on-off-on-off-on) power of the device (2 to 4 seconds between each on and off). Wait a few moments until the lighting starts blinking rapidly.
AP Mode:
• No need to power down the device, but need to keep the lighting device blinking rapidly. Then turn on and off three times (on-off-on-off-on) power of the device (2 to 4 seconds between each on and off). Wait a few moments until the lighting starts blinking slowly. -
If my Wi-Fi/Internet goes down, will ENSHINE smart bulbs still work?
LEDEPLY products need to be connected to Wi-Fi in order to use them remotely. -
Can I share with family and friends?
Yes, you can share your bulbs with family and friends who will have access to control your bulbs. In the Smart Life app, press the Profile button and click on the ‘Share Device’ button, and you will be able to give or revoke sharing permissions. In order to share, the other user should already have downloaded the Smart Life app and registered a new account. -
The bulb appears offline or unreachable, what should I do?
Check the light switch and make sure that it is switched ON. The light bulb requires an ‘always-on’ power supply to operate properly. Make sure your Wi-Fi router is online and in range. When your change the Wi-Fi password, the bulb will disconnect, you can turn on-off 10 times to reset and reconnect it. -
What’s the Wireless Range?
The range of your home Wi-Fi is heavily dependent on your home router and the conditions of the room. Check with your router specifications for exact range data.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>