Panasonic FZ-55 SeriesFZ-55 Series Personal Computer Instruction Manual
- June 6, 2024
- Panasonic
Table of Contents
FZ-55 SeriesFZ-55 Series Personal Computer
Instruction Manual
Terms and illustrations in these instructions
In these instructions, the names and terms are referred to as follows.
“Windows 10 Pro” as “Windows” or “Windows 10”
– (Settings): Click (Start) and then click (Settings).
: Page in these Operating Instructions.
: Reference to the on-screen manuals.
Please read these instructions carefully before using this product, and save
this manual for future use.
Update the on-screen manuals.
Safety Precautions
To reduce the risk of injury, loss of life, electric shock, fire, malfunction,
and damage to equipment or property, always observe the following safety
precautions.
Explanation of symbol word panels
The following symbol word panels are used to classify and describe the level
of hazard, injury, and property damage caused when the denotation is
disregarded and improper use is performed.
DANGER
Denotes a potential hazard that will result in serious injury or death.
WARNING
Denotes a potential hazard that could result in serious injury or death.
CAUTION
Denotes a hazard that could result in minor injury.
NOTICE
Denotes a hazard that could result in property damage.
The following symbols are used to classify and describe the type of instructions to be observed.
| This symbol is used to alert users to a specific operating procedure that
must not be performed.
---|---
| This symbol is used to alert users to a specific operating procedure that
must be followed in order to operate the unit safely.
DANGER
Precautions on the Battery Pack
Electrolyte leakage, generation of heat, ignition or rupture of the Battery
Pack may result.
|
-
Do Not Throw the Battery Pack into a Fire or Expose It to Excessive Heat
-
Do Not Deform, Disassemble, or Modify the Battery Pack
-
Do Not Short the Positive (+) and Negative (-) Contacts
→Do not place the battery pack together with articles such as necklaces or hairpins when carrying or storing. -
Do Not Apply Shocks to the Product by Dropping It, Applying Strong Pressure to It, etc.
→If this product is subjected to a strong impact, remove the battery pack from the computer immediately. -
Do Not Charge the Battery Using Methods Other Than Those Specified
-
Do Not Use the Battery Pack with Any Other Product
• The battery pack is rechargeable and was intended for the specified product. -
Do Not Use This Product with a Battery Pack Other Than the One Specified
→Use only the specified battery pack with your product.
---|---
|
-
Avoid Extreme Heat (Near the Fire, in Direct Sunlight, for Example)
-
When the Battery Pack Has Deteriorated or If
Abnormal Swelling Occur, Replace It With a New One
→Do not continue to use a damaged battery pack. not a malfunction or Trouble Occurs, Immediately Stop Use -
If the battery pack appears to be damaged or deformed, or if it
emits smoke, abnormal odor, excessive heat, or other abnormality, removes it from the computer immediately.
WARNING
Fire or electric shock may result.
|
-
Do Not Do Anything That May Damage the AC cord, the AC Plug, or the AC Adaptor Do not damage or modify the cord, place it near hot tools, bend, twist, or pull it forcefully, place heavy objects on it, or bundle it tightly.
→Do not continue to use a damaged AC cord, AC plug, and AC adaptor.
• Contact your technical support office for repair. -
Do Not Connect the AC Adaptor to a Power Source Other Than a Standard Household AC Outlet
→Connecting to a DC/AC converter (inverter) may damage the AC adaptor. On an airplane, only connect the AC adaptor/charger to an AC outlet specifically approved for such use. -
Do Not Pull or Insert the AC Plug
If Your Hands Are Wet -
Do Not Disassemble This Product
• No user-serviceable parts inside this unit. Refer servicing to a qualified technician. -
Do Not Touch This Product In a Thunderstorm If Connected with the AC Cable or Any Other Cables
-
Do Not Place Containers of Liquid or Metal Objects on Top of This Product
→If the foreign matter has found its way inside, immediately turn the power off and unplug the AC plug (and remove the battery pack). Then contact your technical support office.
---|---
|
-
If a Malfunction or Trouble Occurs, Immediately Stop Use If the Following Malfunction Occurs, Immediately Unplug
the AC Plug and the Battery Pack
• This product is damaged
• Foreign object inside this product
• Smoke emitted
• Unusual smell emitted
• Unusually hot
→After the above procedure, contact your technical support office for repair. -
Clean Dust and Other Debris of the AC Plug Regularly
•If dust or other debris accumulates on the plug, humidity, etc. may cause a defect in the insulation. -
Insert the AC Plug Completely
→Do not use a damaged plug or loose AC outlet. -
Close the Connector Cover Tightly When Using This Product Where Is a Lot of Water, Moisture, Steam, Dust, Oily
Vapors, etc.
→If the foreign matter has found its way inside, immediately turn the power off and unplug the AC cord, and then remove the battery pack. Then contact your technical support office. -
Turn the Power off Beforehand when Entering Locations, Such as a Gas Station Where Inflammable Gases Are Generated
• Such gases may be ignited.
Burns or low-temperature burns may result.
|
- Do Not Use This Product in Close Contact With Your Body For a Long Period of Time Ö Do not use this product with its heat-emitting parts in close contact with your body for a long period of time.
• Low-temperature burns may result.
---|---
WARNING
Burns or low-temperature burns may result.
|
-
Do Not Expose Yourself or Other Persons to the Hot Wind from the Ventilation Hole (Exhaust) For a Long Period of Time
• Depending on the direction of the computer or the way you hold the computer, your hands and body will be more exposed to the hot wind.
• Covering the ventilation hole (exhaust) with your hand or another object can cause heat to build up inside, possibly resulting in burns. -
Do Not Touch The Surface of The AC Adaptor Continuously While Using/Charging
• Burns may result. -
Do Not Place the Product in a Bag or Case While It is Turned On
• Doing so may cause the product to overheat and result in burns.
---|---
Detrimental health effects on your body may result.
|
-
Do Not Turn the Volume Up Too Loud When Using Headphones
• Listening to high volumes that overstimulate the ear for long periods of time may result in loss of hearing. -
Do Not Leave a nanoSIM Card within Reach of Infants
→In case of swallowing, consult a doctor immediately.
---|---
Radio waves transmitted from this product may affect the surrounding area.
|
- Do Not Use This Product near Automatic Control Devices, Such As Automatic Doors And Fire Alarms
• Automatic control devices may malfunction, resulting in accidents.
---|---
Radio waves transmitted from this product may affect the surrounding area.
|
-
nTurn the Power Off on an Airplane *1
→For use on a plane, follow the airline’s instructions.
• The safety of navigation may be compromised. -
Turn the Power Off in Hospitals or at Locations Where Medical Equipment is Present1
→Do not bring this product into operating rooms, intensive care units, CCU, etc. 2
• Medical electrical equipment may be affected, and malfunction may occur, resulting in accidents. -
Turn the Power Off in Crowded Locations, Such As a Crowded Train, Where There May Be a Person with a Cardiac Pacemaker
• The operation of a pacemaker may be affected. -
Keep This Product at Least 15 cm Away from the Position of an Implantable Pacemaker
• The operation of a pacemaker may be affected.
---|---
1If there is no choice but to use this product in such an environment, turn the wireless capability off. However, bear in mind that use of a computer may be prohibited during takeoff and landing of an aircraft, etc. even if the wireless capability is turned off.
2 CCU is an abbreviated term of Coronary Care Unit.
CAUTION
Fire or electric shock may result.
|
-
Do Not Move This Product While the AC Plug Is Connected
→If the AC cord is damaged, unplug the AC plug immediately. -
Do Not Connect a Telephone Line, or a Network Cable Other Than the One Specified, Into the LAN Port
→ Do do not connect to a network such as the ones listed below.
• Networks other than 1000BASE-T, 100BASE-TX or 10BASE-T
• Phone lines (IP phone (Internet Protocol Telephone), Telephone lines, internal phone lines (on-premise switches), digital public phones, etc.) -
Do Not Subject the AC Adaptor To Any Strong Impact
→ Do not continue to use the AC adaptor after a strong impact such as being dropped.
→Contact your technical support office for repair. -
Do Not Leave This Product in High-Temperature Environment for a Long Period of Time
• Leaving this product where it will be exposed to extremely high temperatures such as near fire or in direct sunlight may deform the cabinet and/or cause trouble in the internal parts. -
Do Not Block the Ventilation Hole (Exhaust/Intake)
→Do not use this product wrapped in cloth or on top of bedding or a blanket.
---|---
|
- Hold the Plug When Unplugging the AC Plug
- Use Only the Specified AC Adaptor With This Product
→Do not use an AC adaptor other than the one supplied (supplied with the unit or one sold separately as an accessory).
This product may fall over or drop, resulting in an injury.
|
- Do Not Place This Product on Unstable Surfaces
---|---
|
- Avoid Stacking
Detrimental health effects on your body may result.
|
-
Do Not Look Into the Optical Disc Drive
-
Looking directly at the internal laser light source may result in damage to eyesight.
→Contact your technical support office for the check, maintenance, and repair. -
Do Not Use Discs That Are Cracked or Deformed
• Because the discs rotate at high speeds, damaged discs may break apart causing injury.
→Discs that are not round and discs that have been repaired using adhesives are similarly dangerous, and so should not be used.
---|---
|
- Take a Break Of 10-15 Minutes Every Hour
• Using this product for long periods of time may have detrimental health effects on the eyes or hands.
Burns, low-temperature burns, or frostbite may result.
|
- Do Not Expose the Skin To This Product When Using the Product In A Hot Or Cold Environment
→When it is necessary to expose the skin to this product such as to scan a fingerprint, perform the operation in the shortest time possible.
---|---
NOTICE
- Do not place the computer near a television or radio receiver.
- Keep the computer away from magnets. Data stored on the hard disk may be lost.
- This computer is not intended for the display of images for use in medical diagnosis.
- This computer is not intended for use with the connection of medical equipment for the purpose of medical diagnosis.
- Panasonic shall not be liable for loss of data or other incidental or consequential damages resulting from the use of this product.
- Do not touch the terminals on the battery pack.
- The battery pack may no longer function properly if the contacts are dirty or damaged.
- Do not expose the battery pack to water or allow it to become wet.
- If the battery pack will not be used for a long period of time (a month or more), charge or discharge (use) the battery pack until the remaining battery level becomes 30% to 40% and store it in a cool, dry place.
- This computer prevents overcharging of the battery by recharging only when the remaining power is less than approx. 95% of capacity.
- The battery pack is not charged when the computer is first purchased. Be sure to charge it before using it for the first time. When the AC adaptor is connected to the computer, charging begins automatically.
- Should the battery leak and the fluid get into your eyes, do not rub your eyes. Immediately flush your eyes with clear water and see a doctor for medical treatment as soon as possible.
NOTE
- The battery pack may become warm during recharging or normal use. This is completely normal.
- Recharging will not commence if the internal temperature of the battery pack is outside of the allowable temperature range (0 °C to 50 °C {32 °F to 122 °F}). ( Operating Instruc- tions – Reference Manual “Basic Operation” “Battery Power”) Once the allowable range requirement is satisfied, charging begins automatically. Note that the recharging time varies based on the usage conditions. (Recharging takes longer than usual when the temperature is 10 °C {50 °F} or below.)
- If the temperature is low, the operating time is shortened. Only use the computer within the allowable temperature range.
- The battery pack is a consumable item. If the amount of time the computer can be run by using a particular battery pack becomes dramatically shorter and repeated recharging does not restore its performance, the battery pack should be replaced with a new one.
- When transporting a spare battery inside a package, briefcase, etc., it is recommended that it be placed in a plastic bag so that its contacts are protected.
- Always power off the computer when it is not in use. Leaving the computer on when the AC adaptor is not connected will exhaust the remaining battery capacity.
While we anticipate the use of our products in certain environments such as
nuclear equipment/ systems, air traffic control equipment/systems, aircraft
equipment/systems (as defined in 3 ), medical devices or accessories (as
defined in 4 ), medical treatment diagnosis image display, life support
system, or other equipment/devices/ systems that are involved with ensuring
human life or safety, we do not allow users to integrate our product such that
it becomes an integral part of the systems found in these environments.
Panasonic will not be responsible for any liability resulting, and in any way
for any damages or loss resulting from the use of this product arising out of
the foregoing uses.
3 Aircraft equipment/systems including Electric Flight Bag (EFB) systems are defined by FAA AC120-76D or EASA Commission Regulation (EU) No 965/2012.
4 As defined by the Regulation (EU) 2017/745 Medical Device Regulation.
Panasonic cannot guarantee any specifications, technologies, reliability,
safety (e.g. flammability/ smoke/toxicity/radio frequency emission, etc.)
requirement related to aviation standards that exceed the specifications of
our COTS products.
Regulatory Information
Information to the User / Informations destinées aux utilisateurs
<Only for model with wireless LAN/Bluetooth>
This product and your Health
This product, like other radio devices, emits radiofrequency electromagnetic
energy. The level of energy emitted by this product however is far much less
than the electromagnetic energy emitted by wireless devices like for example
mobile phones.
Because this product operates within the guidelines found in radio frequency
safety standards and recommendations, we believe this product is safe for use
by consumers. These standards and recommendations reflect the consensus of the
scientific community and result from deliberations of panels and committees of
scientists who continually review and interpret the extensive research
literature.
In some situations or environments, the use of this product may be restricted
by the proprietor of the building or responsible representatives of the
organization.
These situations may for example include:
- Using this product onboard airplanes, or
- In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
If you are uncertain of the policy that applies to the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use this product prior to turning on the product.
Regulatory Information
We are not responsible for any radio or television interference caused by
unauthorized modification of this product. The correction of interference
caused by such unauthorized modification will be the responsibility of the
user. We and its authorized resellers or distributors are not liable for
damage or violation of government regulations that may arise from failing to
comply with these guidelines.
Optical Disc Drive Caution
Laser Devices
- Labeling/Marking
Beam Divergence
- Vertical angle: 30 degree
- Horizontal angle: 36 degrees
650 nm, 1 mW MAX, 16.8 ms
AC Adaptor
- The AC adaptor used for the specified computers and Port Replicator option is Class I Equipment. When using the computer and Port Replicator option, the AC adaptor must be earthed. The power plug must be connected to a properly wired earth ground socket outlet. The hazardous voltage could occur on user-accessible metal parts by improperly wiring socket outlet.
*1Equipment with basic insulation used as a basic safeguard, and with protective bonding and protective earthing used as a supplementary safeguard for electrically-caused injury.
USB Type-C Adaptors and Cables
For USA/CANADA:
- Use only UL Listed USB Type-C AC adaptors.
- Use only UL Listed USB Type-C cables (ICT Power Cables).
LED Light
- The light from the LED is strong and can injure human eyes.Do not look directly at the LEDs with naked eyes.
Lithium Battery
Lithium Battery!
This computer contains a lithium battery to enable the date, time, and other
data to be stored. The battery should only be exchanged by authorized service
personnel.
Warning!
Risk of explosion from incorrect installation or misapplication may possibly
occur.
Battery Pack
CAUTION:
Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used
Batteries According to the Instructions.
Handling of the lithium-ion battery pack
Do not charge, use, or leave the battery in extremely high temperature or
extremely low air pressure like high altitude where ordinary not entered, as
this may result in explosion or leakage of flammable liquids.
Battery pack model number | FZ-VZSU1HU |
---|---|
Recommended charging condition (Constant voltage/current) | 12.6 V / 3150 mA |
Notice | •Dispose of a used battery pack according to local ordinances and/or |
regulations.
•Do not expose this computer to temperatures greater than 60 °C {140 °F}.
•Charging Limit Voltage:
12.6 V: 0 – 45 °C (Charging start temperature: 2 °C and over)
12.15 V:45 – 60 °C
Energy Star
< Only for model with the above logo on the computer>
As an ENERGY STAR® Partner, Panasonic Corporation has determined that this
product meets ENERGY STAR® guidelines for energy efficiency. By enabling
available power management settings, Panasonic computers enter a low-power
sleep mode after a period of inactivity, saving the user energy.
For U.S.A.
Federal Communications Commission Radio Frequency Interference Statement
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the Panasonic Service Center or an experienced radio/TV technician for help.
Warning
To assure continued compliance, use only shielded interface cables when
connecting to a computer or peripheral. Also, any changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC RF Exposure Warning:
-
Other third-party wireless transmitters have not been RF exposure evaluated for use with this computer and may not comply with FCC RF exposure requirements.
<Only for model with wireless LAN/wireless WAN/Bluetooth> -
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
-
This equipment has been approved for mobile operation, and unless otherwise advised in separate supplemental instructions for individual wireless transmitter(s), requires a minimum of 20 cm spacing be provided between the antenna(s) and all person’s body (excluding extremities of hands, wrist, and feet) during wireless modes of operation.
-
This equipment may not be co-located or operated with any other antenna or transmitter.
Responsible Party:
Panasonic Corporation of North America
Two Riverfront Plaza
Newark, NJ 07102
Support Contact: https://na.panasonic.com/us/support
USA Only: Disposal may be regulated in your community due to environmental considerations. For disposal or recycling information, please visit Panasonic website: https://www.panasonic.com/us/corporate/sustainability.html or call 1-888-769-0149
- This equipment is provided with external antenna connector(s) for connection to optional Car Mounter or Port Replicator for mobile external mounted antenna(s). External antenna(s) must be professionally installed and cannot exceed recommended maximum antenna gain as described in individual provided supplement instructions for wireless transmitters. The Car Mounter is provided with Radiall/Larsen WLAN whip antenna, type NMO5E2400BKTNC with 5 dBi antenna gain. The maximum allowable antenna gains for the external WWAN base whip antenna for the 700 MHz, 850 MHz, 1700 MHz, and 1900 MHz bands are 6 dBi, 9 dBi at 2500 MHz and 2600 MHz bands, and 0 dBi at 3600 MHz bands. Also, the user must maintain minimum 20 cm spacing between the external antenna(s) and all person’s body (excluding extremities of hands, wrist, and feet) during wireless modes of operation.
<US & Canada Only>
A lithium-ion battery that is recyclable powers the product you have
purchased.
Please call 1-800-8-BATTERY for information on how to recycle this battery.
For Used in Motor Vehicle
Warning: Notebook Computer may be installed in a motor vehicle and visible to the driver only if used to support vehicle-related functions such as vehicle information, system control, rear or side observation and navigation. If used for entertainment purposes, such as television reception or video play, it must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Check with individual state/provincial laws to determine lawful use of this product while operating within a motor vehicle.
This product contains a CR Coin Cell Lithium Battery which contains
Perchlorate Material – special handling may apply.
See https://dtsc.ca.gov/perchlorate/
For Canada
Canadian ICES-003
CAN ICES-3(B)/NMB-3(B)
<Only for model with wireless LAN/Bluetooth>
ISED Canada
This product complies with ISED Canada’s license-exempt RSSs.
Operation is subject to the following two conditions;
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate with the Radiall/Larsen whip antenna,
type NMO5E2400BKTNC WLAN antenna having a maximum gain of 5 dBi. A WLAN
Antenna having a higher gain is strictly prohibited per regulations of ISED
Canada. The Required antenna impedance is 50ohms.
To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power
(EIRP) is not more than that required for successful communication.
<Only for model with wireless LAN/wireless WAN/Bluetooth>
- This computer complies with ISED Canada radiation exposure limits set forth for an uncontrolled environment.
- This PC with WLAN and/or Bluetooth transmitters installed has been approved for portable operation and does not require any minimum spacing be provided between antennas and all person’s bodies.
FOR USE WITH MODEL NO. : CF-AA5713A
Hint:
If you want to get a copy of the original DoC of our above-mentioned products,
please contact our web address: https://www.ptc.panasonic.eu/
Authorized Representative:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries must not be mixed
with general household waste. For proper treatment, recovery and recycling of
old products and batteries, please take them to applicable collection points,
in accordance with your national legislation. By disposing of them correctly,
you will help to save valuable resources and prevent any potential negative
effects on human health and the environment.
For more information about collection and recycling, please contact your local
municipality. Penalties may be applicable for incorrect disposal of this
waste, in accordance with national legislation.
Note for the battery symbol (bottom symbol):
This symbol might be used in combination with a chemical symbol. In this case,
it complies with the requirement set by the Directive for the chemical
involved.
For Australia
For Used in Motor Vehicle
Warning: Notebook Computer may be installed in a motor vehicle and visible to
the driver only if used to support vehicle-related functions such as vehicle
information, system control, rear or side observation and navigation. If the
Notebook Computer is to be used for work or entertainment purposes, such as
television reception, video play, or other work programs, it must be installed
in a position where it will NOT:
(a) be visible, directly or indirectly, to the operator of the motor vehicle;
or
(b) cause distraction to drivers of other motor vehicles.
Check with individual state laws to determine lawful use of this product while
operating within a motor vehicle. If the visual display unit is, or is part
of, a driver’s aid, the above rule is not applied. “Driver’s aid” includes
closed-circuit television security cameras, dispatch systems, navigational or
intelligent highway and vehicle system equipment, rearview screens, ticket-
issuing machines, and vehicle monitoring devices.
For India
Declaration of Conformity with the requirements of the E-Waste (Management)
Rules
The Product is in conformity with the requirements of the reduction of
hazardous substances of the E-Waste Rules.
The content of hazardous substance with the exemption of the applications
listed in SCHEDULE II of the E-waste Rules:
- Lead (Pb) – not over 0.1% by weight;
- Cadmium (Cd) – not over 0.01% by weight;
- Mercury (Hg) – not over 0.1% by weight;
- Hexavalent chromium (Cr6+) – not over 0.1% by weight;
- Polybrominated biphenyls (PBBs) – not over 0.1% by weight;
- Polybrominated diphenyl ethers (PBDEs) – not over 0.1% by weight.
For the purpose of recycling to facilitate effective utilization of resources,
please return this product to a nearby authorized collection center,
registered dismantler or recycler, or Panasonic service center when disposing
of this product.
Please see the Panasonic website for further information on collection
centers, etc., or call the toll-free number below.
Website:https://www.panasonic.com/in/corporate/sustainability/panasonic-
india-i-recycle-program.html
Service helpline: 1800 103 1333 or 1800 108 1333
Do’s & Don’ts: – E-Waste (Management) Amendment Rules 2018
S.No. | Do’s | Don’ts |
---|---|---|
1 | All electrical and electronic products are required to be handed over only | |
to the authorized recycler. | The product should not be opened by the User |
himself/herself, but only by authorized service personnel.
2| The product should be handed over only to an authorized recycler for
disposal.| The product is not meant for re-sale by any unauthorized
agencies/scrap dealers/kabariwalahs.
3| Keep the product in an isolated area, after it becomes non-
functional/unrepairable so as to prevent its accidental breakage.| The product
is not meant for mixing into house-hold waste streams.
4| For more information about collection and recycling, please contact your
local municipality.| Do not keep any replaced spare part(s) from the product
in the exposed area.
5| Always Dispose of products that have reached end-of-life at Panasonic India
authorized service center.| Do not donate old electronic items to anybody.
6| Wherever possible or as instructed, separate the packaging material
according to responsible waste disposal options and sorting for recycling.| Do
not give e-waste to informal and unorganized sectors like Local Scrap
Dealer/Rag Pickers.
7| Create environment awareness PAN India Level.| Do not dispose your product
in garbage bins along with municipal waste that ultimately reaches landfill.
Before Turning on the Computer
Refer to the following URL for how to attach options to the Expansion areas
and replace the keyboard. Confirm the part numbers of the optional items
before connection.
https://askpc.panasonic.co.jp/manual/option/w/
Expansion Areas
IMPORTANT
- If the above options are not attached, be sure to attach a dummy pack or cover before using it.
First-time Operation
Preparation
- Check and identify the supplied accessories.
If you do not find the described accessories, contact your support office.
-
Soft Cloth ………………………………………………. 1
-
Stylus …………………………………………………. 1
-
Tether …………………………………………………. 1
-
OPERATING INSTRUCTIONS – Read Me First (This book) …………… 1
Depending on the model, the following items are supplied. -
BD Drive Utility Disc or DVD Drive Utility Disc ……………………. 1
Latest Information on Windows 10
When Microsoft Windows 10 is updated, the screen display or operation
procedures may be changed.
For the latest information on Windows 10, see the following web page.
https://pc-dl.panasonic.co.jp/itn/addendum/
- Insert the battery pack
Insert the battery pack until it touches the secured position.
< Only for model with second battery pack>
IMPORTANT
- Make sure the latch is securely locked. Otherwise, the battery pack may fall when you carry the computer.
- Do not touch the terminals of the battery pack and the computer. Doing so can make the terminals dirty or damaged, and may cause malfunction of the battery pack and the computer.
Inserting RAM module for expansion
-
Use recommended RAM module products. Do not use non-recommended RAM modules.
Non-recommended RAM modules may not operate properly and may cause damage to your computer. -
When adding a RAM module, read Operating Instructions – Reference Manual and mount it using the specified method. Otherwise, the expected performance may not be achieved.
-
Use the tether to attach the stylus to the computer (only for model with a touchscreen)
Use the tether to attach the stylus to the computer so you will not lose it. Before attaching the pen (A), take out it from the pen holder (B). There is a tether hole (C) to attach it. -
Open the display 1. Push the top of the latch (D) to release it.
2. Hold the side/handle of the computer with either of your hands and then lift up the display to open.
IMPORTANT
• Do not open the display wider than necessary (180° or more), and do not apply excessive pressure to the LCD. Do not open or close the computer holding the edge of the LCD segment. -
Connect your computer to a power outlet 1. Connect the power cord and AC adaptor.
Hold plug A of the power cord, and securely insert it straight to the end.
2. Open the cover.
3. Connect the AC adaptor to the DC-IN jack B of the computer.
4. Connect your computer to a power outlet.
The shape of the AC Plug and AC Outlet depends on the country. The battery charging starts automatically. -
Turn on the computer
Press and hold the power switch (E) until the power indicator (F) lights.
IMPORTANT
• Do not press the power switch repeatedly.
• Once you turn off the computer, wait for ten seconds or more before you turn on the computer again.
• Do not perform the following operation until the drive indicator turns off.
• Disconnecting the AC adaptor
• Pressing the power switch
• Touching the keyboard, touchpad, touchscreen <only for a model with touchscreen> or external mouse
• Closing the display
• Any changes from the default setting of the Setup Utility l When the CPU temperature is high, the computer may not start up to prevent overheating of the CPU. Wait until the computer cools down, and then turn the power on again. If the computer does not power on even after cooling down, contact Panasonic Technical Support ( Operating Instructions – Reference Manual). -
Setup Windows
Select language and click [Yes].
Follow the on-screen instructions.
•The computer restarts several times. Do not touch the keyboard, touchpad or touchscreen, and wait until the drive indicator has turned off.
•After the computer is turned on, the screen remains black or unchanged for a while, but this is not a malfunction. Wait for a moment until the Windows setup screen appears.
•During setup of Windows, use the touchpad and click to move the pointer and to click an item.
•Setup of Windows will take approximately 5 minutes. Go to the next step, confirming each message on the display.
•You can set the Wireless Network after the setup of Windows is complete.
If “Let’s connect you to a network” is displayed, you can select [I don’t have internet]. If “There’s more to discover when you connect to the internet”, you can select [Continue with limited setup].
•We recommend that you set the password after the setup of Windows is complete.
•If Microsoft Edge-related screens are displayed, click [Get started] and follow the on-screen instructions.
IMPORTANT
• You can change the user name, image, and security setting after the setup of Windows.
• Use standard characters as a computer name: numbers 0 through 9, uppercase and lowercase letters from A to Z, and the hyphen (-) character. Do not use the following words and characters for user name: CON, PRN, AUX, CLOCK$, NUL, COM1 to COM9, LPT1 to LPT9, LPT, &, space.
If the error message “The computer name is not valid” appears, check if characters other than the above are not entered. If the error message still remains on the display, set the key entry mode to English (“ENG”) and enter characters. -
Restart the computer
1. Click (Start).
2. Click **(Power) – [Restart].
• A portion of the Panasonic PC Settings Utility functions will be enabled after the computer restarts.
NOTE
** 1. When the “Emergency notification setting” screen appears, read the on- screen messages carefully. Follow the on-screen instructions. You can set the “Emergency notification setting” after the setup of Windows is complete. -
Update the on-screen manual
1. Connect to the internet. Sign in to Windows as an administrator.
For further information, refer to **** Connect to a network.
2. Update the on-screen manual.
Click (Start) – [Panasonic PC Manual Selector].
Follow the on-screen instructions. -
Create a recovery disc
A recovery disc allows you to install OS and restore its factory default condition, in case, the recovery partition of the flash memory is damaged.
Refer to ****Operating Instructions – Reference Manual “Important Operation/Settings” “Create a Recovery Disc” about creating the disc.
NOTE
-
To set the password, proceed as follows.
1. Click (Start) – (Settings) – [Accounts] – [Sign-in options].
2. Click [Password] – [Add].
To display the password input screen every time the computer is resumed from the modern standby or hibernation, perform the following setting.
1. Click (Start) – (Settings) – [Accounts] – [Sign-in options].
2. Select [Every Time] under “Require sign-in”. -
Set the key entry mode to English (“ENG”) and enter characters.
The keyboard layout can be added or changed in the following steps.
1. Click (Start) – (Settings) – [Time & Language] – [Language].
2. Click a language and click [Options].
3. Click [Add a keyboard] and choose a keyboard from the list. -
Remember your password. If you forget the password, you cannot use Windows. Creating a password reset disk beforehand is recommended.
-
PC Information Viewer
This computer periodically records the management information of the flash memory, etc.
The maximum data volume for each record is 1024 bytes.
This information is only used for estimating the cause in the case when the flash memory goes down by any possibility. They are never sent to outside via network nor used for any other purpose except for the purpose described above.
To disable the function, add the checkmark for [Disable the automatic save function for management information history] in [Hard Disk Status] of PC Information Viewer, and click [OK].
Then follow the on-screen instructions.
( ****Operating Instructions – Reference Manual “Troubleshooting” “Troubleshooting” “Checking the Computer’s Usage Status”)
Software License
This product incorporates the following software:
- the software developed independently by or for Panasonic Corporation,
- the software owned by a third party and licensed to Panasonic Corporation,
- the software licensed under the GNU General Public License Version 2.0 (GPL V2.0),
- the software licensed under the GNU LESSER General Public License, Version 2.1 (LGPL V2.1), and/or
- open-source software other than the software licensed under the V2.0 and/or LGPL V2.1.
The software categorized as (3) – (5) are distributed in the hope that it will
be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Please refer to the
detailed terms and conditions thereof shown in the ****Operating
Instructions – Reference Manual “Appendix” “Software License”.
At least three (3) years from delivery of this product, Panasonic will give to
any third party who contacts us at the contact information provided below, for
a charge no more than our cost of physically performing source code
distribution, a complete machine-readable copy of the corresponding source
code covered under GPL V2.0, LGPL V2.1 or the other licenses with the
obligation to do so, as well as the respective copyright notice thereof.
Contact Information: oss-cd-request@gg.jp.panasonic.com
The source code and the copyright notice are also available for free on our
website below.
https://panasonic.net/cns/oss/
Panasonic Corporation
Osaka, Japan
Panasonic System Solutions Company of North America
Two Riverfront Plaza
Newark, NJ 07102
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario L4W 2T3
Panasonic Australia Pty. Limited
ACN 001 592 187 ABN 83 001 592 187
1 Innovation Road, Macquarie Park, NSW 2113
Web Site: https://panasonic.net/cns/pc/
© Panasonic Corporation 2021
Printed in Taiwan
HS0521-0
DHQX1773ZA/T1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>