REDFIRE 85013 Chicago Firebowl Instruction Manual

REDFIRE 85013 Chicago Firebowl

Tools required (not included):

Safety Instructions

• IMPORTANT – Carefully remove any packaging before use, but retain the safety instructions.
• These instructions form part of the product.
• Please take note of all of the safety warnings listed in these instructions.
• Please read these instructions in their entirety and retain them for future reference.
• These instructions should be stored with the product.
• This product is for domestic use ONLY and should not be used commercially or for contract purposes.

Care and Safe Use Guidelines

WARNINGS – CAUTION!

• This product is intended FOR OUTDOOR USE ONLY. DO NOT USE INDOORS.
• WARNING – ALWAYS keep children and pets at a safe distance from the product when in use.
• NEVER leave a burning fire unattended.
• DANGER of carbon monoxide poisoning – NEVER light this product or let it smolder or cool down in confined spaces.
• DO NOT use this product in a tent, caravan, car, cellar, loft or on a boat.
• DO NOT use under any awnings, parasols or gazebos.
• FIRE HAZARD – Hot embers may emit while in use.
• CAUTION – DO NOT use petrol, white spirit, lighter fluid, alcohol or other similar chemicals for lighting or relighting. ONLY use firelighters that comply to EN:1860-3.
• This product is ONLY suitable for use with untreated wood, logs
• DO NOT use coal or charcoal in this product.
• DO NOT use this product on decking or any other flammable surfaces such as dry grass, wood chips, leaves or decorative bark.
• Ensure that the product is positioned at least 2m away from flammable items. Also, ensure that there is a minimum overhead clearance of 2m from the top of the unit.
• DO NOT use this product as a furnace – ONLY use as a patio heater.
• ATTENTION – This product will become very hot. DO NOT move it during operation.
• This product is NOT intended for cooking or heating food.

CARE & USE

• Ensure that the product is positioned on a permanent flat, secure, heat resistant, non-flammable surface away from flammable items.
• Ensure that the product has a minimum of 2m overhead clearance and a minimum of 2m clearance from other surrounding items.
• Decide on the location as above. The assembled product is heavy and it is therefore recommended that the unit is not moved once positioned and must NOT be moved whilst in use. If it is necessary to move it once it has cooled, please use 2 persons to lift (do not drag) the product across the floor.
• Ensure the model is stable prior to use.
• The unit may be left outside all year if a La Redfire weatherproof cover is used to help protect it from bad weather.
• As this model is made from steel, the surface will age and develop surface rust as soon as it is placed outside and from first use. This is to be expected, does not affect use and is not a product fault.
• Please see below the instructions on how to refresh the paint finish if desired.
• To help reduce surface rust, rub the product with an oily rag after each use.
• For safety reasons, always inspect your product prior to use for signs of fatigue and damage, and replace your model as and when necessary. Continuing to use a damaged unit could cause personal injury or damage to property.
• ALWAYS use heat-resistant gloves during use and when adding fuel.

LIGHTING & REFUELLING

• This product is ONLY suitable for use with untreated wood, logs or
• Prepare a stack of loosely crumpled newspapers and place on top of the log grate.
• Pile finely split dry firewood or kindling on top of the paper.
• To light, the newspaper, use long safety matches or a long-nosed lighter.
• Once sufficiently alight, add logs or larger pieces of untreated wood to the unit to increase the heat slowly.
• DO NOT overload with fuel, only one or two logs is sufficient.
• ALWAYS use heat-resistant gloves and the safety tool when adding fuel and handling the mesh cover, as the unit will become very hot.

EXTINGUISHING

• To extinguish – stop adding fuel and allow the fire to die or douse with sand. DO NOT use water as this may damage the product.

STORAGE

• When not in use, and if stored outside, cover the product once it has cooled completely with a La Redfire weatherproof cover.
• Remove loose paint and rust with a wire brush when needed and re-paint the product using La Redfire High Temperature Paint.

Parts List

Prior to assembly: read the instructions carefully. Check all parts against the parts list. Carry out assembly on a soft surface to avoid scratching the paint. Please retain this information for future reference. For ease of assembly only loosely tighten bolts and then tighten fully when the assembly is complete.
WARNING – DO NOT over-tighten bolts; only tighten with moderate pressure to avoid damaging the bolts or components of the fire bowl.

Assembly Diagram

IMPORTANT – Remove any packaging before use, but retain the safety instructions and store them with this product.
ASSEMBLY
STEP 1 – Insert M8 x 25mm bolt (A) through cone spring (8) into the foot (7) and into the leg (5) and fasten until secure. Repeat the process until 3x leg assemblies are complete.
STEP 2 – Insert M8 x 25mm screw (B) through the bowl (3) and into leg assembly and fasten until secure.
STEP 3 – Repeat the process until all 3x leg assemblies are attached to the fire bowl.
STEP 4 – Place the fire bowl on its feet.
STEP 5 – Place log grate (4) into the fire bowl.
STEP 6 – Attach mesh safety cover handle (1) to mesh safety cover (2) using the hardware attached. The product is now ready to use but please ensure you have read these instructions thoroughly prior to use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>