RUROC Lite Helmet Instruction Manual

RUROC Lite Helmet

PRODUCT INFORMATION

WARNING

• All Ruroc helmets are built to provide extreme protection, and meet or exceed the standards set out for snow sports safety helmets.
• No helmet can offer complete protection against injury or death in an accident, even at low speeds, so it is important that you ensure you wear this helmet correctly and take all necessary precautions to ensure your safety, including riding within your skill level and abilities. This is your responsibility.
• This helmet is for non-motorized recreational snow-sports, such as snowboarding, skiing and other alpine sports, and should not be used when riding motorized vehicles, such as snowmobiles and motorbikes.
• Replace and destroy this helmet after impact even if no damage is visible. The internal integrity of the EPS liner may be compromised even if the damage cannot be seen and the plastic outer shell is intact. EPS degrades and over time, this can lead to it becoming unfit for purpose. You should aim to replace your helmet after 3 years of use for this reason. Exposure to direct sunlight can negatively affect the life of EPS.
• WARNING! This helmet should not be used by children while climbing, or while doing activities which have a risk of strangulation/hanging if the child gets trapped within the helmet.
  • (Fig.A)
  • (Fig. B)
  • (Fig.C)

FITTING / SIZES

• WARNING: If the helmet is worn in the wrong position, it cannot provide you with full protection and, in the case of an accident, can result in serious injury or even death.
• WARNING: If the helmet is worn in the wrong position, it cannot provide you with full protection and, in the case of an accident, can result in serious injury or even death.

EYE PROTECTION

We recommend that you use this helmet with bespoke RUROC goggles. These goggles are seamlessly integrated into the design of this helmet and give maximum performance if used together.

HELMET CARE / CLEANING / STORAGE

• Clean your helmet inside and outside regularly with lukewarm mild soap/water and a soft cloth. Do not use aggressive detergents or solvents or rough brush/cloth. Remove the padding from the helmet and hand wash with lukewarm mild soap/water. Do not machine wash or tumble dry the padding. Let all parts fully dry before assembly, use, or storage.
• WARNING: Do not use solvents, detergents, thinner, petroleum-based products (eg gasoline), bleach, ammonia, and other cleaning agents as they may damage the materials of the helmet. The damage may not be visible to the user.
• WARNING: Do not remove or modify any components or parts. Do not make any modifications to the chinstrap or the buckle. Do not make any modifications to the internal shape of the helmet or on its external shell. Do not cut or drill any parts, nor fit any not certified accessory to the helmet.

WARRANTY INFORMATION

If you have any questions regarding our products or the above warranty, please feel free to contact our service center by e-mail at: Info@ruroc.com

WARRANTY PROCESS

Before returning any product please contact Info@ruroc.com and a member of the team will be able to arrange a pre-paid return labels for you to send the product back to us.

WARNING

• All Ruroc helmets are built to provide extreme protection, and meet or exceed the standards set out for snow sports safety helmets.
• No helmet can offer complete protection against injury or death in an accident, even at low speeds, so it is important that you ensure you wear this helmet correctly and take all necessary precautions to ensure your safety, including riding within your skill level and abilities. This is your responsibility.
• This helmet is for non-motorized recreational snow-sports, such as snowboarding, skiing and other alpine sports, and should not be used when riding motorized vehicles, such as snowmobiles and motorbikes.
• Replace and destroy this helmet after impact even if no damage is visible. The internal integrity of the EPS liner may be compromised even if the damage cannot be seen and the plastic outer shell is intact. EPS degrades and over time, this can lead to it becoming unfit for purpose. You should aim to replace your helmet after 3 years of use for this reason. Exposure to direct sunlight can negatively affect the life of EPS.
• WARNING! This helmet should not be used by children while climbing, or while doing activities which have a risk of strangulation/hanging if the child gets trapped within the helmet.

FITTING / SIZES

• Use the size adjustment wheel at the back of the helmet to tighten or loosen your helmet in order to guarantee the best fit! We offer a variety of sizes to ensure that you can choose the size which provides the best fit for you, and will exchange any helmet within 14 days of receipt for any sizing issues.

• The helmet may not give the maximum level of protection in the case of an accident if it is too loose or too tight, which may result in injury or death. It is your responsibility to ensure that your helmet fits you correctly. The chinstrap must be fastened at all times when the helmet is in use. Do not wear any other form of headwear along with this helmet.

• If you notice any difficulties in the fitting of your helmet, please contact your authorized RUROC dealer or customer service.

• Wear the helmet horizontally (fig. A). It must not tilt forward (fig. B) or backwards (fig. C).

  • WARNING: ‘If the helmet is worn in the wrong position, it cannot provide you with full protection and, in the case of an accident, can result in serious injury or even death.
    When wearing the helmet, it should not move freely without moving your scalp along with it. You can check this by holding the helmet firmly and trying to move your head within the helmet. If the helmet moves freely choose the next smaller size. Close the buckle and tighten the chin strap so that it feels snug under your chin. Move your head to check that you are still able to breathe, talk and swallow normally. Adjust straps if necessary. Do not wear the strap over the chin, nor use any additional chin cups or similar. Before using the helmet do a final check by tilting the helmet backwards and forwards. The helmet should remain firmly in place and cannot be taken off in any direction. If the helmet can move freely, rotate or gives a loose fit, use the next size down.

  • WARNING: If the helmet is worn in the wrong position, it cannot provide you with full protection and, in the case of an accident, can result in serious injury or even death.

EYE PROTECTION

We recommend that you use this helmet with bespoke RUROC goggles. This goggles are seamlessly integrated into the design of this helmet and give maximum performance if used together.

HELMET CARE / CLEANING / STORAGE

• Clean your helmet inside and outside regularly with lukewarm mild soap/water and a soft cloth. Do not use aggressive detergents or solvents or rough brush/cloth. Remove the padding from the helmet and hand wash with lukewarm mild soap/water. Do not machine wash or tumble dry the padding. Let all parts fully dry before assembly, use or storage.
  • WARNING: Do not use solvents, detergents, thinner, petroleum based products (e.g. gasoline), bleach, ammonia and other cleaning agents as they may damage the materials of the helmet. The damage may not be visible to the user.
  • WARNING: Do not remove or modify any components or parts. Do not make any modifications to the chinstrap or the buckle. Do not make any modifications to the internal shape of the helmet or on its external shell. Do not cut or drill any parts, nor fit any not certified accessory to the helmet.
• Do not expose the helmet to temperatures over 50°C (around 122°F), such as those it may experience in direct sunlight or in a car. Heat may damage the internal absorption structure. Damages may not be visible to the user. Store the helmet in a dry and dark place when not in use.

WARRANTY INFORMATION

• Ruroc warrants all products to be free of defects in material or workmanship for a period of one year from the date of purchase, subject to the provisions below.
• If a Ruroc product fails due to defects in craftsmanship or materials, within the warranty period, we will repair or replace the product free of charge provided that you promptly notify us of any defect (in any event within 7 days) and you immediately cease to use the product in question. Be aware that this warranty is limited to the original purchaser only. For detailed information please see the guideline below and/or the product specification following the product.
• If you have any questions regarding our products or the above warranty, please feel free to contact our service centre by e-mail at: Info@ruroc.com

WARRANTY PROCESS:

1. Before returning any product please contact Info@ruroc.com and a member of the team will be able to arrange a pre-paid return labels for you to send the product back to us.
2. Ensure that the returned product is washed, cleaned and dried before shipping. Dirty and/or foul smelling helmets will be returned unprocessed, or may delay the process with an additional surcharge.
3. Remember to include a note with your name, address and phone number, AND fill out the returns form. Please make sure to include a short statement explaining the warranty problem.
   Alternatively, you may also return your product to the store from where you originally purchased the product. Any Ruroc dealer is able to handle the warranty process on your behalf.
   NOTE: Damage due to wear and tear, accident, misuse, or neglect, or if you fail to store or use a product other than in accordance with the instructions provided, or damage due to any repairs carried out by you or a third party not authorised by us, is not covered under warranty. Please contact our warranty department if you have any questions.

Meets:

• EN1077:2007, Class B
• ASTM F2040-11
• EN1077 Class A and Class B helmets are for alpine skiers and snowboarders and similar groups. Class A helmets offer comparatively more protection. Class B helmets may offer greater ventilation and better hearing but protect a smaller area of the head and give a lesser degree of protection from penetration.
• This helmet is designed to protect the head during a collision with an obstacle whilst skiing or snowboarding. It has passed EN 1077:2007 to show confirmity to the EHSR of Regulation (EU) 2016/425 and Regulation (EU) 2016/425 as amended to apply in GB.
• You can find the Declaration of conformity on this website: www.ruroc.com/lite

EU-TYPE & UK TYPE EXAMINATION CONDUCTED BY

References

• Ruroc | Home (US)
• Ruroc | Lite

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>