TPP640S Air Purifier Therapure Instructions

TPP640S Air Purifier Therapure

TECHNICAL DATA

INTRODUCTION

With UV light and filtration to clean the air, the Therapure® TPP640S air purifier will greatly improve the quality of the air in your home, office or other environments.
Once you’ve experienced the purity of Therapure® TPP640S air, visit us at our website to find out more ways to improve the quality of your air and your life with our premium products and upgrades.
Please be sure to read the following instructions carefully to ensure optimal performance and safety.
envion.com

PRODUCT BENEFITS

5-STAGE PURIFICATION PROCESS

1. Pre-Filter
2. Cleanable Filter
3. UV Lamp
4. Photo Catalyst Filter
5. ION Boost

MORE BENEFITS

• 3 speed fan setting–lets you select the desired cleaning level.

• Auto mode to automatically adjust fan speed de-pending on air quality:
  Red: air quality is poor
  Orange: air quality is fair
  Blue: air quality is good

• 24-hour timer for automatic power off

• Night mode to dim the control panel light when you sleep.

• Clean filter indicator

• Remote Control

MAIN PARTS

1. Locking Latch

2. Air Inlet Grill

3. Pre-Filter

4. Filter

5. UV Lamp Cover

6. Control Panel: Time, On/Off, Speed,
   UV/VOC, Auto, ION and Night Mode

7. Air Quality Indicator Light

8. Air Outlet Grill

9. UV Lamp

10. Remote Control

OPERATING THE THERAPURE® TPP640S

SAFETY
Before using the Therapure® TPP640S air purifier, please read the following important information.
Do not run the Therapure® TPP640S with a broken filter. Replace the filter if the filter has a tear or a hole in it.

1. Do not place near fans.
   

2. Keep both sides of the unit at least 30 centimeters away from a wall.
   

3. Do not place the unit near curtains.
   

4. Placing the unit close to the source of air pollution is an effective way to improve indoor air quality.
   

CONTROLS / SETTINGS

Power Control – To operate the Therapure® TPP640S, press the Power button to turn on the air purifier and ionizer.

TIMER CONTROL

The Therapure® TPP640S air purifier can be programmed to turn off after a preset amount of time. Press the “TIME” button to program the timer. Each press will add one hour up to a total of 24 hours. Keeping the button pressed will automatically in-crease to 24 hours, 1 hour at a time, after that it will turn back to off.

ION GENERATOR

The Ionizer is always on when the device is running.

FAN SPEED CONTROL

The Therapure® TPP640S has three different speeds of cleaning, LOW, MED and HI. Press “SPEED” button to cycle the settings and select the fan speed you desire. The speed state will be shown on the LED display.

AUTO MODE

The Therapure® TPP640S is equipped with an air sensor to monitor the quality of your air. Simply press the “AUTO” button to activate the air monitoring system. The monitor will test the air quality and automatically adjust the fan speed to remove the air contaminants. The front of the display is equipped with LED lights to notify you of the air quality. RED color is for poor, ORANGE for fair and BLUE for good quality air.

CLEAN FILTER INDICATOR LIGHT

The Therapure® TPP640S Clean Filter Indicator Light will turn on each time the filter needs to be cleaned. To reset the filter indicator, press the ON/OFF and UV/VOC buttons together for 3 seconds. The CLEAN FILTER light will flash 3 times and then turn off completely, indicating the unit has been reset.

DIM MODE

If the LED lights are too bright, activate the “DIM Mode” to turn off the LED lights and the lighted display. To turn on Dim mode, simultaneously press Auto and Time buttons. Power indicator, however, will remain lit.

UV CONTROL

Press the “UV/VOC” control button for UV/VOC to turn on the UV lamp and the photocatalyst filter.

The remote control has a coin cell battery. Keep the remote and the battery away from Children. If the battery is ingested, immediately seek medical attention. Never put the coin battery in your mouth for any reason as they are easily swallowed accidentally. Discard coin batteries carefully.

PREPARING THE REMOTE CONTROL

1. Remove the plastic tab from the bottom of the remote by gently pulling on the tab.
   

2. Turn the air purifier on and off by pressing the Power button.

USING THE REMOTE CONTROL

• Control speed with the “Speed” button.
• Control the timer with the “Time” button.
• Turn the UV light on and off with the “UV/VOC” button.
• Turn the Auto function on and off with the “Auto” button.
• Set the air purifier to Dim mode by pressing the “Dim” button.

REPLACING THE BATTERY

Replace the battery clip by pressing on the release tab while simultaneously pulling the battery clip out.

• Only replace with: CR2025 Lithium cell battery.
• Insert the cell in the battery clip with “+” facing up and insert the battery clip into the remote.

When inserting the battery clip into the re-mote, turn the remote backside up.

CLEANING & MAINTENANCE

Keep the Therapure® TPP640S functioning properly by cleaning the cleanable Filter every four weeks of use. More frequent cleaning will be necessary if the unit is located in an area with a high level of air-borne contaminants (excessive amounts of smoke, pet dander, etc.).
Exposing the Therapure® TPP640S to candle/oil/fireplace soot and smoke is not recommended and will require more frequent cleaning.
Always make sure the Therapure® TPP640S is turned off and unplugged before cleaning.

• Vacuuming will restore performance of the cleanable HEPA-Type Filter. However, the filter may appear stained. This is normal and does not affect performance in any way.
• Do not use water or any household cleaners or detergents to clean the Filter.
• The inlet grill may be cleaned (after unit is turned off and unplugged) with a vacuum or a slightly damp cloth.

CLEANING

1. Release the inlet grill by pressing on the locking latch (see diagram of Main Parts).
   

2. Remove the inlet grill from the unit.
   

3. Grasp the left and right frames of the Filter through the indentations on the sides of the filter enclosure and remove the filter.
   

4. To clean the Filter, use the brush or crevice attachment with a vacuum cleaner. Run the attachment along the inlet and outlet side of the filter, cleaning between the crevices as much as possible.

5. Once the Filter has been cleaned and checked for any possible damage, replace the filter back in the reverse direction described here. Plug in the unit and down the ON/OFF + UV/VOC button for 3 seconds. The clean filter light will go off and your cleaning maintenance is done.

CLEANING THE PRE-FILTER

1. Release the air inlet grill by pressing on the locking latch.
2. Gently remove the pre-filter from the air inlet grill.
3. To clean the pre-filter, simply submerge in warm soapy water. Gently lift and submerge the pre-filter several times until it is clean.
4. Rinse the pre-filter with clean water and allow it to dry completely before placing it back to the air inlet grill.

CLEANING EXTERNAL SURFACES

1. Turn off and unplug unit.
2. Use a washcloth slightly dampened with a little water and dishwashing soap to wipe the outer case surfaces.
3. Do not allow water to slip into the internal parts as this could damage your unit and result in electrical shock and injury to you.
4. Allow the unit to thoroughly dry before use.

UV LAMP

The lifetime of the UV lamp is up to 12 months of continuous, effective operation. After this time, the bulb may remain illuminated, but its effectiveness is greatly reduced. For maximum effectiveness, replace the UV bulb annually.
Do not touch the glass part of the lamp. Oil from fingertips will decrease the effective-ness of the lamp.
Never operate the unit without a filter or with a damaged filter. UV lamp cover must be in-stalled at all times. The UV light from the UV lamp will result in severe damage to eyes and could cause blindness.

REPLACING THE UV LAMP

Before replacing the UV lamp, make sure the Therapure® TPP640S air purifier is turned off and unplugged. Let the lamp cool down for 5 minutes before replacing it.

1. Release the inlet grill by pressing on the locking latch.
   

2. Grasp the left and right frames of the filter through the indentations on the sides of the filter enclosure and remove filter.
   

3. Remove the two bolts used to fix the UV lamp cover and remove the cover out from the unit, then unscrew the old UV lamp from the lamp base of the unit.
   

4. Install the new UV lamp into the lamp base of the unit.

5. Install the UV lamp cover with the two bolts on the unit.
   

6. Install the inlet grill on the unit.
   

ABOUT THE AIR MONITOR

The TPP640S is designed with an air monitor to track the quality of your air. Over time the monitor can become dirty and may require cleaning. The main symptom of a dirty air monitor is the LED display remains frozen on one light color. In order to clean the air monitor you must use a vacuum to clear the monitor chamber.

CLEANING THE AIR MONITOR

1. Power off and unplug unit.

2. Locate the 3 small vent holes in the rear of the unit just about the inlet grill.
   

3. Use a vacuum cleaner hose to suction any dust or dirt that may have accumulated inside the monitor chamber.
   

TROUBLESHOOTING

button.
Unit is unplugged.| Check to ensure unit is plugged in.
The inlet grill has not been installed & locked into place.| Check to make sure filter and inlet grill is properly installed & locked into place.
Reduced airflow or poor filtering| The inlet or outlet grill may be blocked.| Check to ensure nothing is blocking the air inlet & outlet.
Cleanable filter may be clogged.| Check & clean the filter, if necessary.

envion.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>