MODINE AIR13-111.5 Steam / Hot Water Convectors

MODEL NOMENCLATURE

Convectors

DESIGN BENEFITS
ENCLOSURE STYLES
Convector cabinets are available in four attractive and functional styles to fit a wide range of architectural requirements.

TYPE SL
Fully exposed convector designed for wall mounting. Features a louvered outlet grille in the Slope-Top that keeps debris from accumulating
on the top of the unit. The air inlet
is directed through the bottom to produce high outputs.
TYPE SF
This fully exposed floor unit has sloping outlet louvers and is designed for mounting to a sidewall. The air inlet is directed through the bottom front inlet louver. An optional arched inlet is available.
TYPE FL
This fully exposed floor-mounted convector is attached to the wall. The flat top design features front inlet and outlet louvers. The front panel is fastened to the liner.
TYPE PL
This fully recessed wall convector is designed to provide high outputs. The liner is recessed completely into the wall, and the front panel is fastened to the liner. Front inlet/outlet louvers are standard with sidewall mounted units.

HEATING ELEMENTS

Heating elements are available in three standard nominal depths: 4″ (2-tubes), 6″ (3-tubes), and 8″ (4-tubes). The assembly is protected by shield plates running the entire length of the element, and is supported in enclosure by a welded bracket to eliminate strain on piping or element. Fins of .010″ aluminum have integral collars to assure uniform spacing. Tubes are mechanically expanded into collars to permit maximum heat transfer. Headers are cast brass with top or bottom tappings. One header can be reversed to be mounted “up”, while the other is mounted “down”, for reverse piping applications.
Figure 4.1 – Element Connections

Commercial Fin Tube Radiation
Technical Manual AIR13-111.5

ENCLOSURE CONSTRUCTION
Convectors are specially constructed to satisfy the requirements of strength, durability and safety in many different building applications. Cabinets are all suitably braced and reinforced and are available in heavy-gauge steel for special institutional applications.
END POCKETS
End pockets may be installed at one or both ends of the Cabinet Convectors. The heating element is shortened and a vertical baffle with element support is provided between the end of the element and the end of the cabinet. End pockets are available in 6″ or 8″ widths. (Note: Size unit capacities for actual coil length.)
Figure 4.2 – End Pocket Options

GRILLE OPTIONS
Convector front covers are available with louvered, perforated, or aluminum bar grille openings. All are designed to allow directional flow of air with maximum free open area. The four cover grille types are as follows:

• Die-formed louvered inlet/outlet. (Standard)
• Heavy-duty architectural inlet/outlet grilles with a deep-etched clear anodized (R-204) finish. The aluminum bar grille shall have vanes of continuous extrusion with a 15° deflection.
• Security inlet/outlet perforations with 1/8-inch diameter holes 1/4-inch staggered center lines.
• Arched inlet and a die-formed louvered outlet.

Figure 4.3 – Grille

ACCESS DOORS
Access door options are provided in the front panel of cabinet convectors for inspection or operation of valves, traps or air vents. These doors are hinged on one side with a heavy-duty hinge. A concealed 1/4-turn locking device may be provided with an optional Allen-head operator when security conditions dictate. Refer to page 14 for available door locations.
Figure 4.4 – Door Hardware

DESIGN BENEFITS

DAMPER
The damper assembly covers the entire outlet area of the enclosure and consists of a 20-gauge damper blade, which
is flanged top and bottom for additional rigidity. Damper assemblies are available with a knob operator or an optional tamper-resistant operator. The tamper-resistant operator functions with a simple Allen wrench and is particularly valuable in school or institutional settings where supervisory operation only is desired.
Figure 5.1 – Damper Options

COVER FASTENERS
The removable front cover shall be supported by a top panel clip and fastened at the bottom with a screw on each side. The standard screws are Phillips head with tamper-proof Spanner head screws available as an option.
Figure 5.2 – Fasteners

INSULATION
1/2″-thick fiberglass insulation is available on convector sides, tops, fronts or backs for special applications. (Top insulation does not apply to SF and SL models.)
SPECIAL FINISH
All convectors are thoroughly cleaned and phosphatized after fabrication and finished with a polyester-epoxy powder coating. As an option, cabinets may be finished in one of the standard decorator colors (see color chart 13-416).

Convectors

DESIGN BENEFITS

Typical Piping Arrangements
VAPOR AND VACUUM SYSTEMS (STEAM)
Convectors are not recommended for one-pipe steam systems. Typical connections are shown below. Other arrangements, however, can be used.
Fig.1 –
This arrangement of down-feed hook-up is used when
the steam mains are above the Convectors with drops which are connected to the unit. This arrangement can be used only with freestanding units. The valve is shown inside the cabinet as it can easily be operated by lifting the removable front for an optional access door. A thermostatic control valve with a bulb in the inlet may be substituted for the hand-operated valve shown. The valve can also be installed outside the cabinet if desired. (Valve and piping installed by others.)

Fig. 2 – This shows an arrangement for an up-feed hook-up for semi-recessed or for freestanding units. A straight through tap of proper size may be substituted for the angle trap shown. This allows access to the valve.
On all steam systems, the convector element should pitch down to the return.

HOT WATER SYSTEMS
Two different arrangements are shown below for hot water piping connections, down-feed and up-feed.

Fig. 3 –
This shows a down-feed arrangement. The supply must be above the tube level of the convector. Air valves are not needed at the individual units. A proper piping system allows for the collection of air and venting at the high point.On all down-feed systems, the pitch should be down toward the return.

Fig. 4 –

This shows an up-feed arrangement which can be used with first floor units when mains are in the basement or where the upper floors are supplied by risers from lower floors. Up-feed systems require venting at each convector, and the pitch should be down toward the supply.An optional chamber with a remote air vent is available consisting of 3/4″ coupling, 3/4″ to 1/8″ reducing bushing and 6″ air assembly. CORRECTION FACTORS – STEAM

Steam
Table 7.1 – Correction Factors for Steam Pressures Other than 1 Psi Gauge
To determine the heating capacity (Btu/hr) of a convector at a given steam pressure and entering air temperature (EAT) other than standard, multiply the standard capacity at 1 lb. entering steam pressure and 65° EAT by the factor from this table as shown in Formula 7.1.

Table 7.2 – Inlet Grille/Louver Correction Factors
To determine the actual BTU ratings of a convector with an inlet grille/louver, multiply standard output by the correction factor listed below as shown in Formula 7.1.

Depth

| Reduction Factor
---|---
Height
18″| 20″| 26″| 32″
4″| 0.946| 0.950| 0.959| 0.980
6″| 0.907| 0.915| 0.942| 0.970
8″| 0.888| 0.900| 0.902| 0.945

Table 7.3 – Altitude Correction Factors
To determine the actual BTU ratings of a convector at varying altitudes, multiply standard output by the correction factor listed below as shown in Formula 7.1.

Formulas: Steam

Convectors

CORRECTION FACTORS – HOT WATER

Hot Water
Table 8.1 – Correction Factors for Entering Water Temperature and Entering Air Temperature other than Standard To determine the heating capacity (Btu/hr) of a convector at an entering water temperature (EWT) and entering air temperature (EAT) other than standard, multiply the capacity at 200°F EWT and 65°F EAT by the factor from this table as shown in formula 8.1. NOTE: GPM must be identical to that at 200°F EWT and 65°F EAT.

Entering Water Temp. (EWT)| Entering

Air Temperature (EAT)

---|---
40| 45| 50| 55| 60| 65 (std)| 70| 75| 80| 85
160| 0.83| 0.80| 0.75| 0.73| 0.69| 0.66| 0.62| 0.59| 0.56| 0.52
170| 0.97| 0.94| 0.88| 0.85| 0.81| 0.77| 0.73| 0.69| 0.65| 0.61
180| 0.98| 0.95| 0.89| 0.86| 0.81| 0.78| 0.74| 0.70| 0.66| 0.62
190| 1.12| 1.08| 1.02| 0.99| 0.93| 0.89| 0.84| 0.80| 0.75| 0.71
(std) 200| 1.26| 1.22| 1.15| 1.11| 1.05| 1.00| 0.95| 0.90| 0.85| 0.80
210| 1.40| 1.36| 1.28| 1.24| 1.17| 1.12| 1.06| 1.00| 0.94| 0.89
220| 1.55| 1.50| 1.41| 1.36| 1.29| 1.23| 1.17| 1.10| 1.04| 0.98
230| 1.69| 1.64| 1.54| 1.49| 1.41| 1.34| 1.28| 1.21| 1.14| 1.07

Table 8.2 – Correction Factors for Water
Temperature Drop other than Standard
To determine the actual BTU ratings at water temperature drops (WTD) other than 20°F, use Formula 8.1 to multiply the standard BTU rating, based on a 20°F water temperature drop, by the following factors.

Table 8.3 – Ethylene Glycol Correction Factors
To determine the actual BTU ratings of a convector with a water/ethylene glycol solution multiply standard output by the correction factor listed below as shown in Formula 8.1.

Percent Ethylene Glycol

| Average Solution Temperature (°F)
---|---
100| 150| 200| 250
40| 0.855| 0.875| 0.910| 0.925
50| 0.820| 0.850| 0.870| 0.900
60| 0.770| 0.800| 0.830| 0.850
70| 0.725| 0.750| 0.780| 0.825
80| 0.680| 0.715| 0.740| 0.770
90| 0.630| 0.660| 0.695| 0.725
100| 0.586| 0.620| 0.645| 0.680

Table 8.4 – Inlet Grille Correction Factors
To determine the actual BTU ratings of a convector with an inlet grill, multiply standard output by the correction factor listed below as shown in Formula 8.1.

Depth

| Reduction Factor
---|---
Height
20″| 26″| 32″
4″| 0.95| 0.96| 0.98
6″| 0.92| 0.94| 0.97
8″| 0.90| 0.90| 0.95

Table 8.5 – Altitude Correction Factors
To determine the actual BTU ratings of a convector at varying altitudes, multiply standard output by the correction factor listed below as shown in Formula 8.1.

Formulas: Hot Water
8.1) BTUA = BTUS x Factor
8.2) BTUS = BTUA Factor

Identification of Symbols
BTU = Btu/hr performance
Subscripts
S = Standard operating condition (200° F EWT, 65° F EAT) A = Actual operation conditions

CORRECTION FACTORS

Figure 9.1 – Factors for Calculating Flow Rate (in GPM)
The chart below may be used to determine approximate GPM for a desired MBH for various water temperature drops.

Figure 9.2 – Pressure Drop Convectors – 64″ Long
Curves showing pressure drop for determining pressure head requirement. Based on 64″ length units, but applicable to shorter units, as most loss is due to headers.

Example: MBH 30 WTD 30
GPM = 30 x 0.0687 = 2.06 GPM

DIMENSIONS/FEATURES

Models SL and SF Slope-Top Wall and Floor Mounted

Standard Features

• Cabinet – 18 gauge front, 20 gauge sides and back panel
• Cabinet Dimensions – (24″-64″)L x (4″-8″)D x (18″-32″)H
• Polyester-epoxy powder coating – Prime finish
• Heating Elements – 1/2″ copper tube, 0.010″ aluminum fins
• Opposite end connections
• Louvered air outlet grilles

Options

• Damper – Knob or Allen-Key
• Outlet grill variations (see page 5)
•  Access door options (see page 14)
• Insulation – 1/2″
• Tamper proof fasteners for front panels
•  Decorator colors available (see chart 13-416)
•  End pockets
• Front – 14 or 16 gauge with 14, 16, or 18 gauge liner

PERFORMANCE DATA

Model SL and SF Slope-Top Wall and Floor Mounted
Table 11.1 – Steam Performance Data – BTU/HR at 1 lb. Steam, 65°F EAT ➀ ➀

| Height
---|---
SL| SF
Depth| Length| 18″| 20″| 26″| 32″| 18″| 20″| 26″| 32″

4″

| 24″| 3,936| 4,056| 4,248| 4,416| 3,600| 3,744| 4,080| 4,248
28″| 4,776| 4,896| 5,112| 5,304| 4,320| 4,488| 4,896| 5,112
36″| 6,456| 6,624| 6,936| 7,248| 5,904| 6,096| 6,624| 6,960
40″| 7,296| 7,488| 7,824| 8,112| 6,648| 6,864| 7,512| 7,848
48″| 8,952| 9,192| 9,600| 9,984| 8,136| 8,448| 9,192| 9,624
52″| 9,744| 9,936| 10,440| 10,848| 8,832| 9,144| 9,936| 10,440
60″| 11,400| 11,616| 12,192| 12,816| 10,248| 10,704| 11,616| 12,192
64″| 12,288| 12,528| 13,128| 13,920| 10,992| 11,544| 12,528| 13,176

6″

| 24″| 6,264| 6,432| 6,936| 7,176| 5,424| 5,736| 6,528| 6,960
28″| 7,560| 7,752| 8,328| 8,688| 6,528| 6,888| 7,752| 8,328
36″| 10,152| 10,464| 11,232| 11,616| 8,904| 9,336| 10,488| 11,280
40″| 11,448| 11,784| 12,648| 13,152| 9,984| 10,536| 11,808| 12,696
48″| 14,064| 14,448| 15,528| 16,104| 12,336| 12,888| 14,496| 15,576
52″| 15,288| 15,720| 16,896| 17,592| 13,536| 14,016| 15,720| 16,896
60″| 17,880| 18,360| 19,728| 20,568| 15,792| 16,344| 18,360| 19,728
64″| 19,224| 19,752| 21,216| 22,080| 16,848| 17,640| 19,776| 21,312

8″

| 24″| 7,776| 8,016| 8,640| 9,000| 7,200| 7,392| 8,064| 8,664
28″| 9,408| 9,648| 10,416| 10,824| 8,640| 8,880| 9,648| 10,416
36″| 12,720| 13,080| 14,112| 14,688| 11,760| 12,144| 13,776| 14,136
40″| 14,376| 14,784| 15,936| 16,584| 13,200| 13,656| 14,856| 16,008
48″| 17,664| 18,096| 19,560| 20,376| 16,320| 16,776| 17,760| 19,656
52″| 19,248| 19,752| 21,336| 22,224| 17,712| 18,192| 19,752| 21,336
60″| 22,512| 23,112| 24,960| 26,040| 20,736| 21,288| 23,112| 24,960
64″| 24,216| 24,888| 26,832| 28,008| 22,392| 22,992| 24,960| 26,928

Table 11.2 – Hot Water Performance Data – Slope Top Outlet Types (SL and SF) BTU/HR at 200°F EWT, 65°F EAT, 20°F WTD (190°F AWT) ➀ ➀

| Height
---|---
SL| SF
Depth| Length| 18″| 20″| 26″| 32″| 18″| 20″| 26″| 32″

4″

| 24″| 2,608| 2,687| 2,814| 2,926| 2,385| 2,480| 2,703| 2,814
28″| 3,164| 3,244| 3,387| 3,514| 2,862| 2,973| 3,244| 3,387
36″| 4,277| 4,388| 4,595| 4,802| 3,911| 4,039| 4,388| 4,611
40″| 4,834| 4,961| 5,183| 5,374| 4,404| 4,547| 4,977| 5,199
48″| 5,931| 6,090| 6,360| 6,614| 5,390| 5,597| 6,090| 6,376
52″| 6,455| 6,583| 6,917| 7,187| 5,851| 6,058| 6,583| 6,917
60″| 7,553| 7,696| 8,077| 8,491| 6,789| 7,091| 7,696| 8,077
64″| 8,141| 8,300| 8,697| 9,222| 7,282| 7,648| 8,300| 8,729

6″

| 24″| 4,150| 4,261| 4,595| 4,754| 3,593| 3,800| 4,325| 4,611
28″| 5,009| 5,136| 5,517| 5,756| 4,325| 4,563| 5,136| 5,517
36″| 6,726| 6,932| 7,441| 7,696| 5,899| 6,185| 6,948| 7,473
40″| 7,584| 7,807| 8,379| 8,713| 6,614| 6,980| 7,823| 8,411
48″| 9,317| 9,572| 10,287| 10,669| 8,173| 8,538| 9,604| 10,319
52″| 10,128| 10,415| 11,194| 11,655| 8,968| 9,286| 10,415| 11,194
60″| 11,846| 12,164| 13,070| 13,626| 10,462| 10,828| 12,164| 13,070
64″| 12,736| 13,086| 14,056| 14,628| 11,162| 11,687| 13,102| 14,119

8″

| 24″| 5,152| 5,311| 5,724| 5,963| 4,770| 4,897| 5,342| 5,740
28″| 6,233| 6,392| 6,901| 7,171| 5,724| 5,883| 6,392| 6,901
36″| 8,427| 8,666| 9,349| 9,731| 7,791| 8,045| 9,127| 9,365
40″| 9,524| 9,794| 10,558| 10,987| 8,745| 9,047| 9,842| 10,605
48″| 11,702| 11,989| 12,959| 13,499| 10,812| 11,114| 11,766| 13,022
52″| 12,752| 13,086| 14,135| 14,723| 11,734| 12,052| 13,086| 14,135
60″| 14,914| 15,312| 16,536| 17,252| 13,738| 14,103| 15,312| 16,536
64″| 16,043| 16,488| 17,776| 18,555| 14,835| 15,232| 16,536| 17,840

DIMENSIONS/FEATURES

Model FL and PL Flat-Top Floor and Wall Mounted

Standard Features

• Cabinet – 18 gauge front, 20 gauge sides and back panel
•  Cabinet Dimensions – (24″-64″)L x (4″-8″)D x (18″-32″)H
•  Polyester-epoxy powder coating – Prime finish
• Heating Elements – 1/2″ copper tube, 0.010″ aluminum fins
• Opposite end connections
• Louvered air outlet grilles

Options

•  Damper – Knob or Allen-Key
• Outlet grill variations (see page 5)
• Access door options (see page 14)
• Insulation – 1/2″
• Tamper proof fasteners for front panels
•  Decorator colors available (see color chart 13-416)
•  End pockets
•  Front – 14 or 16 gauge with 14, 16, or 18 gauge liner

PERFORMANCE DATA

Model FL and PL Flat-Top Floor and Wall Mounted Table 13.1 – Steam Performance Data – BTU/HR at 1 lb. Steam, 65°F EAT ➀ ➀

| Height
---|---
FL| PL
Depth| Length| 18″| 20″| 26″| 32″| 18″| 20″| 26″| 32″

4″

| 24″| 2,760| 3,120| 3,696| 3,984| 2,760| 3,120| 3,696| 3,984
28″| 3,312| 3,816| 4,464| 4,776| 3,312| 3,816| 4,464| 4,776
36″| 4,368| 5,136| 6,000| 6,480| 4,368| 5,136| 6,000| 6,480
40″| 4,896| 5,760| 6,768| 7,296| 4,896| 5,760| 6,768| 7,296
48″| 5,952| 7,080| 8,304| 8,952| 5,952| 7,080| 8,304| 8,952
52″| 6,552| 7,800| 9,072| 9,744| 6,552| 7,800| 9,072| 9,744
60″| 7,656| 9,120| 10,608| 11,400| 7,656| 9,120| 10,608| 11,400
64″| 8,136| 9,744| 11,376| 12,264| 8,136| 9,744| 11,376| 12,264

6″

| 24″| 4,032| 4,536| 5,520| 6,144| 4,032| 4,536| 5,520| 6,144
28″| 4,848| 5,520| 6,672| 7,368| 4,848| 5,520| 6,672| 7,368
36″| 6,432| 7,344| 9,000| 9,912| 6,432| 7,344| 9,000| 9,912
40″| 7,248| 8,328| 10,152| 11,184| 7,248| 8,328| 10,152| 11,184
48″| 8,880| 10,200| 12,432| 13,656| 8,880| 10,200| 12,432| 13,656
52″| 9,744| 11,064| 13,536| 14,904| 9,744| 11,064| 13,536| 14,904
60″| 11,400| 13,056| 15,840| 17,424| 11,400| 13,056| 15,840| 17,424
64″| 12,192| 13,992| 17,016| 18,744| 12,192| 13,992| 17,016| 18,744

8″

| 24″| 5,112| 5,712| 6,552| 7,080| 5,112| 5,712| 6,552| 7,080
28″| 6,384| 6,960| 7,896| 8,520| 6,384| 6,960| 7,896| 8,520
36″| 8,712| 9,312| 10,656| 11,520| 8,712| 9,312| 10,656| 11,520
40″| 9,864| 10,536| 12,024| 12,984| 9,864| 10,536| 12,024| 12,984
48″| 11,952| 12,960| 14,736| 15,984| 11,952| 12,960| 14,736| 15,984
52″| 13,464| 14,232| 16,104| 17,424| 13,464| 14,232| 16,104| 17,424
60″| 15,768| 16,656| 18,840| 20,376| 15,768| 16,656| 18,840| 20,376
64″| 16,776| 17,784| 20,256| 21,936| 16,776| 17,784| 20,256| 21,936

Table 13.2 – Hot Water Performance Data – Flat Top Outlet Types (FL and PL) BTU/HR at 200°F EWT, 65°F EAT, 20°F WTD (190°F AWT) ➀ ➀

| Height
---|---
FL| PL
Depth| Length| 18″| 20″| 26″| 32″| 18″| 20″| 26″| 32″

4″

| 24″| 1,829| 2,067| 2,449| 2,639| 1,829| 2,067| 2,449| 2,639
28″| 2,194| 2,528| 2,957| 3,164| 2,194| 2,528| 2,957| 3,164
36″| 2,894| 3,403| 3,975| 4,293| 2,894| 3,403| 3,975| 4,293
40″| 3,244| 3,816| 4,484| 4,834| 3,244| 3,816| 4,484| 4,834
48″| 3,943| 4,691| 5,501| 5,931| 3,943| 4,691| 5,501| 5,931
52″| 4,341| 5,168| 6,010| 6,455| 4,341| 5,168| 6,010| 6,455
60″| 5,072| 6,042| 7,028| 7,553| 5,072| 6,042| 7,028| 7,553
64″| 5,390| 6,455| 7,537| 8,125| 5,390| 6,455| 7,537| 8,125

6″

| 24″| 2,671| 3,005| 3,657| 4,070| 2,671| 3,005| 3,657| 4,070
28″| 3,212| 3,657| 4,420| 4,881| 3,212| 3,657| 4,420| 4,881
36″| 4,261| 4,865| 5,963| 6,567| 4,261| 4,865| 5,963| 6,567
40″| 4,802| 5,517| 6,726| 7,409| 4,802| 5,517| 6,726| 7,409
48″| 5,883| 6,758| 8,236| 9,047| 5,883| 6,758| 8,236| 9,047
52″| 6,455| 7,330| 8,968| 9,874| 6,455| 7,330| 8,968| 9,874
60″| 7,553| 8,650| 10,494| 11,543| 7,553| 8,650| 10,494| 11,543
64″| 8,077| 9,270| 11,273| 12,418| 8,077| 9,270| 11,273| 12,418

8″

| 24″| 3,387| 3,784| 4,341| 4,691| 3,387| 3,784| 4,341| 4,691
28″| 4,229| 4,611| 5,231| 5,645| 4,229| 4,611| 5,231| 5,645
36″| 5,772| 6,169| 7,060| 7,632| 5,772| 6,169| 7,060| 7,632
40″| 6,535| 6,980| 7,966| 8,602| 6,535| 6,980| 7,966| 8,602
48″| 7,918| 8,586| 9,763| 10,589| 7,918| 8,586| 9,763| 10,589
52″| 8,920| 9,429| 10,669| 11,543| 8,920| 9,429| 10,669| 11,543
60″| 10,446| 11,035| 12,482| 13,499| 10,446| 11,035| 12,482| 13,499
64″| 11,114| 11,782| 13,420| 14,533| 11,114| 11,782| 13,420| 14,533

ACCESS DOOR LOCATIONS

Figure 14.1 – Access Door Locations (See Table 14.1)

3 #4

1 #2

5 #6

Table 14.1 – Digit 12 – Access Door Locations (See Figure 14.1) ➀ ➀

Model

|

Arched Inlet

|

Height

|

Length

| One Door| Two Doors
---|---|---|---|---|---
Left Side| Right Side| Left and Right Side
Top| Center| Bottom| Top| Center| Bottom| Top| Center| Bottom

SF

|

No

| 18″| 24″ or 28″| | | 5| | | 6| | |
36″ – 64″| | | 5| | | 6| | | 9
20″ – 32″| All| | 1| 5| | 2| 6| | 7| 9

Yes

| 18″| 24″ or 28″| | | | | | | | |
36″ – 64″| | | | | | | | |
20″ – 32″| All| | 1| | | 2| | | 7|
SL| No| 18″| All| | 1| | | 2| | | 7|
20″ – 32″| All| | 1| | | 2| | | 7|

FL

|

No

| 18″| 24″ or 28″| 3| | 5| 4| | 6| | |
36″ – 64″| 3| | 5| 4| | 6| 8| | 9
20″ – 32″| All| 3| 1| 5| 4| 2| 6| 8| 7| 9

Yes

| 18″| 24″ or 28″| 3| | | 4| | | | |
36″ – 64″| 3| | | 4| | | 8| |
20″ – 32″| All| 3| 1| | 4| 2| | 8| 7|

PL

|

No

| 18″| 24″ or 28″| 3| | 5| 4| | 6| | |
36″ – 64″| 3| | 5| 4| | 6| 8| | 9
20″| 24″ or 28″| 3| 1| 5| 4| 2| 6| | |
36″ – 64″| 3| | 5| 4| | 6| 8| | 9
26″ or 32″| All| 3| 1| 5| 4| 2| 6| 8| 7| 9

Yes

| 18″| 24″ or 28″| 3| | | 4| | | | |
36″ – 64″| 3| | | 4| | | 8| |
20″| 24″ or 28″| 3| 1| | 4| 2| | | |
36″ – 64″| 3| | | 4| | | 8| |
26″ or 32″| All| 3| 1| | 4| 2| | 8| 7|

Doors are 5″ wide and generally 5″ high (4″ for all 18″ high convectors) Example: What doors are available for an FL enclosure with arched inlet, 26″ height, and 24″ length?
Answer: Values for Digit 12 of the model number appear in the chart for Left Top (Digit 12=3), Left Center (Digit 12=1), Right Top (Digit 12=4), Right Center (Digit 12=2), Left and Right Top (Digit 12=8), or Left and Right Center (Digit 12=7). Doors are not available in any other location for this convector selection.

SPECIFICATIONS

GENERAL
Contractor shall install Airedale brand steam/hot water cabinet convector, according to manufacturers published information and applicable local codes.
CABINET
The convector cabinet shall be:

• Wall mounted with a sloping top outlet, Model SL.
•  Floor mounted with a sloping top outlet, Model SF.
• Floor mounted with a flat top, front outlet, Model FL.
•  Recessed wall mounted with a front outlet, Model PL.

The front cover and back liner shall be constructed of cold rolled steel. The material thickness shall be:

1.  18 Ga Cover, 20 Ga Liner (Standard)
2.  18 Ga Cover, 18 Ga Liner
3. 16 Ga Cover, 20 Ga Liner
4.  16 Ga Cover, 18 Ga Liner
5.  16 Ga Cover, 16 Ga Liner
6. 14 Ga Cover, 20 Ga Liner
7. 14 Ga Cover, 18 Ga Liner
8. 14 Ga Cover, 16 Ga Liner
9. 14 Ga Cover, 14 Ga Liner

The removable front cover shall be supported by a top panel clip and fastened at the bottom with a screw on each side.
The screw shall be:

a) Phillips head (Standard)
b) Spanner head

The convector cabinet shall be reinforced and braced where necessary to provide additional stiffness. The heating element supports allow for pitch adjustments of up to 1 inch for return of condensation in steam systems and as required by piping arrangements.
The cover and liner shall be degreased and chemically phosphatized prior to the application of a polyester-epoxy powder coating per the latest Airedale color chart AIR13-416.
The front cover shall have:

•  a die-formed louvered inlet/outlet. (Standard)

• a heavy-duty architectural inlet/outlet grilles with a deep etched clear anodized (R-204) finish. The aluminum bar grille shall have vanes of continuous extrusion with a 15°deflection.

• security inlet/outlet perforations with 1/8-inch diameter holes 1/4-inch staggered center lines.

•  an arched inlet and a die formed louvered outlet. All openings are designed to allow directional flow of air with the maximum amount of free open area. All openings are designed to be “pencil proof”.
  (Optional) The front cover shall feature a damper, operated using heavy-duty screws with 10 threads per inch for variable airflow control. Damper vanes shall be fabricated from 20- gauge cold rolled steel steel and painted to match the enclosure color. The damper vane shall extend the full length of the outlet opening. The operator shall be:

•  Knob type.

•  security Allen-Key type.

(Optional) The convector shall have end pockets for location of valves, shut- offs, or other miscellaneous piping components by others. There shall be a baffle between the element header and the end of the cabinet. The end pocket size and location shall be:

•  6″ Left Hand
•  6″ Right Hand
• 6″ Left and Right Hand
•  8″ Left Hand
•  8″ Right Hand
•  8″ Left and Right Hand

(Optional) The convectors shall have flush mounted, hinged access door(s) located on the front cover at the:

• Left Side, Top Height
•  Left Side, Center Height
• Left Side, Bottom Height
•  Right Side, Top Height
•  Right Side, Center Height f) Right Side, Bottom
• Height Left and Right Side, Top Height
• Left and Right Side, Center Height
• Left and Right Side, Bottom Height

The door(s) shall be reinforced from behind with angle stiffeners. Doors shall be held closed using screw fasteners. The screws shall be:

•  Phillips head (Standard)
• Allen key head
•  Spanner head

(Optional) The convectors shall include 1/2-inch insulation, permanently bonded to the inside of the cabinet liner.
CONVECTOR ELEMENT
The convector heating element is designed for either two-pipe steam or hot water heating systems. They are of non-ferrous construction made up of 1/2-inch nominal diameter copper tubing and die-cut aluminum fins with a thickness of no less than .010 inches. The fins have integral collars which provide maximum heat transfer between the tubes and fins. The tubes are mechanically bonded to the fins to ensure permanent contact. The element shall be:

•  4″ deep with 2 tubes.
•  6″ deep with 3 tubes.
•  8″ deep with 4 tubes.

The entire fin assembly shall be encased in a heavy-gauge galvanized steel frame with spacers locked at regular intervals to provide added protection to the finned element. Headers have a 3/4-inch FPT tapping on each end. The element shall be supplied with:

•  both header tappings facing down.
•  reverse header connection tappings, one facing up and the other down.

The assembled heating element shall be hydrostatically tested at 300 PSI. The maximum working pressure for steam is 50 PSI.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>