RCF ART 9 Series Brackets and Covers Owner’s Manual
- June 6, 2024
- RCF
Table of Contents
RCF ART 9 Series Brackets and Covers
SAFETY PRECAUTIONS AND GENERAL INFORMATION
The symbols used in this document give notice of important operating instructions and warnings which must be strictly followed.
|
CAUTION
|
Important operating instructions: explains hazards that could damage a product, including data loss
---|---|---
|
WARNING
| Important advice concerning the use of dangerous voltages and the potential
risk of electric shock, personal injury or death�
|
IMPORTANT NOTES
|
Helpful and relevant information bout the topic
|
SUPPORTS, TROLLEYS AND CARTS
|
Information about the use of supports, trolleys and carts� Reminds to move with extreme caution and never tilt�
|
WASTE DISPOSAL
| This symbol indicates that this product should not be disposed with your household waste, according to the WEEE directive (2012/19/EU) and your national law�
IMPORTANT NOTES
This manual contains important information about the correct and safe use of
the device.Before connecting and using this product, please read this
instruction manual carefully and keep it on hand for future reference. The
manual is to be considered an integral part of this product and must accompany
it when it changes ownership as a reference for correct installation and use
as well as for the safety precautions. RCF S.p.A. will not assume any
responsibility for the incorrect installation and / or use of this product.
IMPORTANT NOTES
Suspending any object is a potentially dangerous operation and should only be
attempted by individuals who have a thorough knowledge of the techniques and
regulations of rigging objects overhead. RCF strongly recommends that all
speakers should be suspended taking into account all current national,
federal, state and local regulations. It is the responsibility of the
installer to ensure that all speakers are safely installed in accordance with
all such regulations. RCF strongly recommends to inspect the system at least
once a year. If any sign of weakness or damage is detected remedial actions
should be taken immediately.The user is responsible for making sure that the
supporting surfaces and any additional hardware used is capable of supporting
the system. Any hardware used to suspend a loudspeaker array that is not
provided by or associated with RCF is not reccomended and is under the
responsibility of others.
SAFETY PRECAUTIONS
- Read these instructions
- Keep these instructions
- Heed all warnings
- Follow all the instructions
- Install in accordance with manufacturer’s instructions
- Only use attachments and accessories specified by the manufacturer
- All the precautions, in particular the safety ones, must be read with special attention, as they provide important information.
Never attempt to carry out any operations, modifications or repairs that are not expressly described in this manual.
RCF S.p.A. strongly recommends this product is only installed by professional qualified installers (or specialised firms) who can ensure correct installation and certify it according to the regulations in force.
IMPORTANT NOTES
RCF declines all responsibilities if the user applies this accessory to other
configurations not mentioned in this manual.
RCF S.p.A. reserves the right to make changes without prior notice to rectify any errors and/or omissions. Always refer to the latest version of the manual on www.rcf.it.
H-BR – HORIZONTAL BRACKETS
OVERVIEW
NOTE: ART9 H-BR are specifically designed to be used only with RCF ART 9 speakers.
SECURING THE BRACKETS TO A WALL
Always secure the bracket by screwing the screws at least through the four corner holes and the central one.
HANGING THE SYSTEM
When hanging the system, add the reinforcement plate to the bracket and hang
the system at least to the central hole or even to the other holes if
necessary.
NOTE: When installing the system always use appropriate and suitable screws to the wall or support.
SECURING THE H-BR TO THE SPEAKER
-
Unscrew the four screws from the lower stand support plate A (On ART 910 also remove the insert label B ).
-
Place the LOWER BRACKET H-BR C over the lower stand support plate and screw it with the screws provided.
-
Place the horizontal bracket on the speaker; on the top side screw the M10 bolt or knob (with its washers) H through the bracket hole.
-
On the bottom side screw the M10 bolt or knob (with its washers) D through the spacer.
Then screw the M6 bolt or knob (with its washers) E on an inclination hole (depending on the inclination needed).
NOTE: once the speaker angle is defined, tighten strongly the M10 knob or bolt. -
The system is now set and ready to be used.
NOTE: ART9 V-BR are specifically designed to be used only with RCF ART 9 speakers.
VERTICAL BRACKETS
OVERVIEW
NOTE: ART9 V-BR are specifically designed to be used only with RCF ART 9 speakers.
SECURING THE BRACKETS TO A WALL
Always secure the bracket by screwing the screws at least through the four corner holes and the central one.
HANGING THE SYSTEM
When hanging the system, add the reinforcement plate to the bracket and hang
the system at least to the central hole or even to the other holes if
necessary.
SECURING THE V-BR TO THE SPEAKER
-
Remove the insert label A placed beside the speaker side handle.
-
Place the inclination bracket B on the handle making the bracket larger hole match with the speaker M10 threaded hole.
NOTE: These exact same operations must be done on both sides of the speaker.
-
Place the bracket C on the speaker making one of the three larger holes D match with the fixing hole.
Each hole allows a different inclination.
The label placed on the bracked explains the possible inclination for every hole.
-
Once chosen which hole to use, screw the M10 bolt or knob (with its washers) E through the fixing hole.
NOTE: These exact same operations must be done on both sides of the speaker. -
Tilt the speaker until you match the inclination needed, then screw the M6 bolt or knob (with its washers) F on a tilt fixing hole.
NOTE: These exact same operations must be done on both sides of the speaker.
NOTE: once the speaker angle is defined, tighten strongly the M10 knob or bolt. -
The system is now set and ready to be used.
FL-BR – FLYING BRACKETS
OVERVIEW
NOTE: ART9 FL-BR are specifically designed to be used only with RCF ART 9 speakers.
FL-BR for ART 910
-
Remove the insert label A placed on top of the speaker.
-
Place the upper bracket B over the speaker top handle making the bracket hole match with the M10 threaded hole on top of the speaker Then screw the M10 bolt (with its washers) C through the bracket hole.
NOTE: tighten strongly the M10 bolt.
-
On the speaker bottom, unscrew the four screws from the lower stand support plate.
-
Place the lower plate D over the lower stand support plate and screw it with the screws provided.
You can now hang the system securing the chains or cables to the two upper
points and to the bottom one.
NOTE: always use appropiate chains, cables and hooks compared to the
system weight.
FL-BR for ART 912/915
-
Remove the three insert labels A placed on top of the speaker and on both sides beside the handles.
-
Place the upper bracket B on top of the speaker making its three holes match with the speaker M10 threaded holes then screw an M10 bolt (with its washers) C on each hole.
NOTE: tighten strongly the M10 bolts. -
On the speaker bottom, unscrew the four screws from the lower stand support plate.
-
Place the lower plate D over the lower stand support plate and screw it with the screws provided.
You can now hang the system securing the chains or cables to the two upper points and to the bottom one.
NOTE:
always use appropiate chains, cables and hooks compared to the system weight.
COVER
RCF S.p.A. Via Raffaello Sanzio, 13 – 42124 Reggio Emilia – Italy
Tel +39 0522 274 411 – Fax +39 0522 232 428 – e-mail:
info@rcf.it – www.rcf.it
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>