wilfa SB-001 Ben Stadler Form Instruction Manual

June 6, 2024
Wilfa

SB-001 Ben Stadler Form
Instruction Manual

wilfa SB 001 Ben Stadler Form

wilfa SB 001 Ben Stadler Form - fig 2

wilfa SB 001 Ben Stadler Form - fig 3

Optional accessory

Water testing strip

WASSERTESTSTREIFEN

Fragrance

DUFTSTOFFE

wilfa SB 001 Ben Stadler Form - Fragrance

Setting up

SOAK CARTRDIGE

wilfa SB 001 Ben Stadler Form - SOAK CARTRDIGE

Share your feedback about Ben on:
www.stadlerform.com/Reviews

For frequently asked questions go to:
www.stadlerform.com/Ben/support

Download instruction manual:
www.stadlerform.com/Ben/manual

Watch the video of Ben:
www.stadlerform.com/Ben/video

Stadler Form Aktiengesellschaft, Chamerstrasse 174, 6300 Zug, Switzerland
Phone +41 41 720 48 48, Fax +41 41 720 48 44, www.stadlerform.com/contact

Congratulations! You have just purchased BEN, the exceptional 3 in 1 appliance (humidifier, aroma diffuser, and fireplace effect).
It will give you great pleasure and improve the indoor air for you.

As with all domestic electrical appliances, particular care is needed with this model also, in order to avoid injury, fire damage or damage to the appliance.
Please study these operating instructions carefully before using the appliance for the first time and follow the safety advice on the appliance itself.

Description of the appliance
The appliance consists of the following main components:

  1. Power adapter
  2. Power adapter connection
  3. Water tank
  4. Tank cover
  5. Maximum mark
  6. On/off button
  7. Lid & Mist outlet
  8. Variable output controller (Humidification and aroma diffusion)
  9. Button for night mode (LEDs normal, dimmed, or off)
  10. Water tray (fragrances can be added to this if wished)
  11. Water level indicator if the water tank is in place
  12. Water Cube™
  13. Air outlet opening (Caution: no water may enter this opening!)
  14. Ultrasonic membrane
  15. Cleaning brush
  16. Cover
  17. Floating switch
  18. LED strip for the fireplace effect
  19. Anticalc cartridge (optional: see “Before setup”)

How your product works
Ben is a 3 in 1 appliance — humidifier, aroma diffuser, and fireplace effect. A membrane that vibrates by means of ultrasound divides water into minuscule droplets, which are then distributed by a ventilator as a mist around the room, where it evaporates. If an essential oil is added to the water, this is also nebulized and blown into the air with the mist. The dimmable Amber Light’ creates the unique fireplace effect by bathing the mist in an amber-colored light.

Important safety instructions
Please read through the operating instructions carefully before you use the appliance for the first time and keep them safely for later reference; if necessary pass them on to the next owner.

  • Stadler Form refuses all liability for loss or damage which arises as a result of failure to follow these operating instructions.

  • The appliance is only to be used in the home for the purposes described in these instructions. Unauthorized use and technical modifications to the appliance can lead to danger to life and health.

  • Use and keep the device out of reach of children.

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

  • Only connect the cable to alternating current. Observe the voltage information given on the appliance.

  • Do not use damaged extension cords.

  • Do not run the power cord over sharp edges and make sure that it does not get trapped.

  • Do not pull the plug from the socket with wet hands or by holding on to the power cord.

  • Do not use the appliance in the immediate vicinity of a bathtub, a shower, or a swimming pool (observe a minimum distance of 3 m).
    Place the appliance such that a person in the bathtub cannot touch the appliance.

  • Keep the device away from heat sources.

  • Do not place the appliance near a heat source. Do not subject the power cord to direct heat (such as a heated hotplate, open flames, hot iron sole plates, or heaters for example). Protect power cords from oil.

  • See to it that the appliance is properly positioned to ensure a high stabil-ity during its operation and make sure that no one can trip over the power cord.

  • The appliance is not splash-proof.

  • For indoor use only.

  • Do not store the appliance outdoors.

  • Store the appliance in a dry place inaccessible to children (pack the appliance).

  • If the power cord is damaged, it must be replaced by the manufacturer or a repair shop authorized by the manufacturer or by similarly qualified persons in order to avoid a hazard.

  • Only use the adapter provided by the manufacturer.

  • Only use fragrances, aromas of essential oils that do NOT contain alcohol. Alcohol can damage the appliance. Appliances that are damaged by such additives are not covered by the warranty.

  • Make sure that the appliance is placed on a surface that is not sensitive to moisture (avoid parquet flooring or delicate carpets).

  • Do not permit the area around the humidifier to become damp or wet. If dampness occurs, turn the output of the humidifier down. If the humidifier output volume cannot be turned down, use the humidifier intermittently. Do not allow absorbent materials, such as carpeting, curtains, drapes, or tablecloths, to become damp.

  • Be aware that high humidity levels may encourage the growth of biological organisms in the environment.

  • Unplug the appliance during filling and cleaning.

  • Never leave water in the water tank when the appliance is not in use.

  • Clean the water tank every 3 days

  • Empty and clean the humidifier before storage. Clean the humidifier before the next use.

  • Warning: Micro-organisms that may be present in the water or in the environment where the appliance is used or stored, can grow in the water tank and be blown in the air causing very serious health risks.

Before setup: Anticalc cartridge and water hardness (optional accessory)
The anti-calc cartridge reduces the limescale in the water and the undesirable emission of limescale particles into the surroundings.
Effective for one to three months, depending on water hardness (see table).

With a water hardness above > 7 ° do, we recommend the use of the anti-calc cartridge (19) to inhibit lime deposits.
Test your water’s hardness (= lime content) with the included testing strip (see page 4). If the strip shows 2 pink boxes, your water hardness is > 7 ° do.

  1. Dip the testing strips into the water for a second
  2. After around one minute, the results can be seen on the testing strips.
    Some of the green boxes change color into pink. The water hardness is shown by how many boxes turn pink. Example: If three boxes are pink, then the water hardness is > 14 ° do.

Important: Soak the anti-calc cartridge in a water bath for 24 hours before the first use (not in the water tank!). The resin has to absorb water to reach high performance.

The period of time that the cartridge is effective depends on the hardness of the water.

Number of
pink boxes| Water hardness| Degree of hardness (°dH)| The cartridge will last for (with 2.5 liter/day)
---|---|---|---
Days| Liter
0/1| Soft| From 4 °dH| 140 days| approx. 360 L
2| Moderately hard| From 7 °dH| 70 days| approx. 180 L
3| Hard| From 14 °dH| 50 days| approx. 120 L
4| Very hard| From 21 °dH| 25 days| approx. 60L

With a water hardness above 21 ° do, we can no longer recommend the use of an ultrasonic air humidifier. We recommend that you use an evaporative humidifier to increase humidity in your house (e.g. Oskar humidifier made by Stadler Form).
The unit only works properly with untreated water. Do not use where there are water softeners and water ionizers in operation. However, Ben may be operated from a drinking water filter system (e.g. Brita). Should you be unsure about the quality or composition of the water in your area, contact the caretaker or the provider of drinking water.

Setting up / operation

  1. Put Ben in the desired location on a flat surface. Connect the power adapter (1) to the unit (2) and plug the adapter (1) into a suitable socket.

  2. Lift up the water tank (3) to the side, out of the way. Unscrew the tank lid (4) and fill the water tank to the maximum mark (5) with clean, cold tap water. Then put the tank into the appliance. To do this, position the water tank (3) sideways again, diagonal to Ben, lift the water tank up and insert it again. Important: Please do not move Ben when it is filled with water. The water could splash out of the interior tank and into the electronics.

  3. Next, start Ben by pressing the On/Off button (6). The LEDs for the fireplace effect will then light up, and the mist will be visible as it comes out of the appliance (7) at variable output controller (8) height.

  4. By turning the variable output controller (8), you can adjust the humidifier output as you wish.

  5. If you are disturbed by the brightness of the illuminated mist (in the bedroom, for example), you can reduce the brightness of the LEDs by pressing the dimmer button (9). You can choose between three different modes:
    • Normal mode (default mode)
    • Dimmed mode (push once)
    • Lights-out mode (push twice)
    • By pushing the dimmer button once more, you can go back into normal mode.

  6. You can also use Ben to fragrance the room. We ask that you be sparing when dealing with fragrances as too much can lead to malfunctions and damage to the unit. To use fragrances, remove the water tank (3) from the unit and trickle the fragrance directly into the water tray (10) (see page 5).
    Add a maximum of 2–3 drops of fragrance per full tank of water. Install the water tank back into the unit.
    Tip: Would you like to change the fragrance? Remove the water tank from the unit, pour the remaining water out and clean the humidifier (see «Cleaning»). Now Ben is ready to distribute a different fragrance of your choice around the room. The intensity with which the aroma is diffused can be adjusted smoothly by sliding the variable output controller.

  7. The water level indicator (11) glows red when the water needs to be refilled. Remove the water tank (3) and fill it up with tap water.
    Replace the water tank.
    The appliance will resume operation after a few seconds.

  8. Would you like to refill the water during operation? You can simply remove the water tank (3) and fill it up. The unit will operate for around a further 5 to 10 minutes with the water that remains in the system. Put the water tank back into the unit within this time period and Ben can continue operation without
    stopping at all.

Note: Should you see droplets (or other signs of dampness) on or around the unit, this is condensed water from the humidifier.
This means that the air can no longer absorb the moisture from the humidifier. Please reduce the humidifier output until you can no longer see any droplets.

Cleaning
Before each piece of maintenance and after every use, turn off the unit and remove the plug from the plug socket. Before you clean Ben, the power adapter (1) must be separated from the power adapter connection (2).
Attention: Never submerge the unit in water (danger of short-circuiting).

  • For hygienic reasons and to ensure proper operation, we recommend the following cleaning intervals.
  • Daily: Fill the water tank (3) with fresh, cold tap water. If the appliance is not used for several days, empty the water from the water tray (10) be- forehand and if necessary, clean it with a bit of dish detergent and a clean cloth. Fill fresh water into the water tank (3), before putting the appliance back into operation.
  • Every 2 weeks: First remove the water tank (3), the lid (7), the cover (16), and the Water Cube’ (12). Clean the inside of the water tray (10,14,17) thoroughly with a bit of dish detergent, warm water, and a soft, clean cloth, sponge, or brush. Use diluted descaling agent (mix according to the manufacturer’s instructions) for lime deposits. Then rinse the water tray (10) thoroughly with cold water and put the water tank (3), the lid (7), the cover (16), and the Water Cube back in.
  • Descaling at least 1x per month. Remove the water tank (3) the lid (7), the cover (16), and the Water tube (12). If limescale deposits form in the water tray (10) we recommend using Stadler Form Cleaner & Descaler (www.stadlerform.com/accessories). Alternatively, you can use a household decalcifier or vinegar. Fill a cup with 200 ml of tap water mixed with descaling agent (mix according to the manufacturer’s instructions). Pour the liquid carefully into the water tray (10). Be sure that no liquid enters the air outlet opening (13). This will damage the appliance and will void any claim to the warranty.
  • Let the descaling agent allow it to take effect according to the manufacturer’s instructions (approx. 30 min.). Check in the water tray (10) if the limescale _On the ultrasonic membrane (14) has dissolved.
  • If limescale residue remains, the ultrasonic membrane (14) can be cleaned I with the help of the cleaning brush (15) (front- and backside). Do not try to crape them with a hard object.
  • fror stubborn limescale, we recommend descaling the appliance several _times in a row.
  • To rinse, now fill the cup with 200 ml of tap water and carefully pour the liquid into the water tray (10). Pour the water out of the appliance at the front right corner. Repeat the process until there is no more descaling agent in the water tray (10). Place the Water tube (12), the lid (7), the cover (16), and the water tank (3) back into the appliance.
  • Regularly as required: For external cleaning, rub with a damp cloth and then dry thoroughly. If the top of the lid (7) shows water and/or fragrance deposits, please clean it using a damp cloth and a bit of dish detergent.
  • At the end of the season: Before putting away the appliance at the end of the season, decalcify as described above. Then clean it thoroughly inside and out and let it dry completely. Insert a new Water tube (12) and anti-calc cartridge (19, optional) in order for your appliance to be ready for the start of the next season. Do not put the appliance away with a used anti-calc cartridge in place, as the granules inside will remain moist for a long time.

Replacement of the anticalc cartridge (optional accessory)

  • Please find the recommended replacement intervals in the table (see «Before setup»).

  • Tip: The efficiency of the cartridge can be inspected with a simple test.
    Hold a small mirror in the mist for a few seconds. If there are then white deposits (calcium carbonate) on the mirror, then the cartridge needs changing.

  • The anticalc cartridge (19) is located on the inner side of the tank cap (4). First, screw the tank cap of the water tank (3) and then screw the cartridge from the tank cap.  Dispose of the cartridge in the domestic waste. Soak the anticalc cartridge in a water bath for 24 hours before the first use (not in the water tank (3)!). The resin has to absorb water to reach high performance.

  • Keep the tank cap when replacing the cartridge!

Water Cube™ – optimal hygiene for your air humidifier
The Water Cube™ (12) by Stadler Form provides optimal hygiene in your air humidifier. It keeps your humidifier running smoothly, extending its lifespan.
The Water Cube™ (12) even works when your appliance is switched off, so the humidifier stays fresh all season long. We recommend replacing the Water Cube™ at the start of the humidifier season.

Repairs

  • Repairs to electrical appliances must only be carried out by a qualified electrical technician. If improper repairs are carried out, the warranty lapses, and all liability is refused.
  • Never operate the appliance if the adaptor or plug is damaged, after it has malfunctioned, if it has been dropped or has been damaged in any other way  (cracks/breaks in the casing).
  • Do not push any object into the appliance.
  • If the appliance is beyond repair, make it unusable immediately by cutting through the cable and handing it in at the collection point provided for the purpose.
  • In the event of a repair, the following points must be observed before the appliance is shipped or taken to the dealer: completely empty the water in the appliance (water tray and any water tank), remove any filters and/ or anti-limescale cartridges, and allow the appliance to dry completely.
    Appliances containing residual water may be damaged during transport, invalidating the warranty

Disposal
The European directive 2012 / 19 / CE on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed-out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliances.

Specifications 100–240 V / 50/60 Hz
Rated voltage 24 W
Power output up to 160 g/h
Humidity output 25 m2 / 63 m3
Room size (up to) approx. 3 days
Running time 338 x 206 x 134 mm

(width x height x depth)
Dimensions| 1.7 kg
Weight| 2.5 Liter
Water tank capacity| 27 – 30 dB(A)
Sound level|
Complies with EU regulations| CE / WEEE / RoHS / EAC

All rights for any technical modifications are reserved

Warranty

2 Years warranty
This warranty covers defects of construction, manufacturing, and material.
Excluded are all wearing parts and improper usage, or consequential damages due to lack of cleaning and/or descaling of the appliance.

wilfa SB 001 Ben Stadler Form - icon 7

Thanks to all people involved in this project: Barry Huang for his engagement and organization, Jerry Lee with Shen Yongjiu for the main engineering and Shu Hebo for his CAD work, Mario Rothenbühler for the photos, Fabian Zimmerli for the unique idea and design, Matti Walker for the graphic work.

Martin Stadler, CEO Stadler Form Aktiengesellschaft

Subscribe to our newsletter!
www.stadlerform.com/Newsletter

MANUFACTURER
Stadler Form
Aktiengesellschaft
Chamerstrasse 174
6300 Zug, Switzerland
Phone +41 41 720 48 48
DISTRIBUTION EU
Stadler Form Germany GmbH
Alt-Heerdt 104
40549 Düsseldorf, Germany
Phone +49 211 97531-640

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals