GSD WL3HR1500 WiFi Module User Manual

GSD WL3HR1500 WiFi Module

Product Information

• Manufacturer: Hui Zhou Gaoshengda Technology Co., LTD
• Model Number: WL3HR1500
• Product Name: WIFI Module
• Standard: IEEE 802.11 b/g/n
• Interface: USB
• Data Transfer Rate: Up to 72.2Mbps
• Operating Systems: Linux, Windows
• Security: Capable of up to 128-Bit WEP Encryption
• Operating Temperature: 5 to 95% maximum (non-condensing)
• Storage Temperature: -20°C to 75°C

Product Usage Instructions

1. Ensure that the product and its accessories are kept out of reach of children.
2. Avoid splashing water or any other liquid onto the product to prevent damage.
3. Avoid placing the product near heat sources or direct sunlight to prevent deformation or malfunction.
4. Keep the product away from flammable materials and naked flames.
5. Do not attempt to repair the product yourself. Only qualified personnel should handle repairs.
6. Install the module using OEM installation only, as specified by the OEM integrator.
7. Comply with FCC regulations regarding interference and radiation exposure limits.
8. Ensure a minimum distance of 20cm between the radiator and your body when installing and operating the equipment.

Please refer to the user manual for further information and safety precautions.

WIFI Module
IEEE 802.11 b/g/n 1T/1R
Model Number: WL3HR1500

Product Descrition

The WL3HR1500 is a 2.4GHz WIFI 1×1 module. This module provides a high level of integration with a IEEE 802.11n MAC/ base band /radio and BLE 4.2.The WLAN operation supports 20MHz channels for data rates up to 72.2Mbps. It fully complies with IEEE 802.11 b/g/n feature rich wireless connectivity at high standards, delivers reliable, cost-effective, throughput from an extended distance.

Product Features

• Complies with IEEE 802.11b/g/n for 2.4GHz Wireless LAN.
• One transmit and One receive path(1T1R)
• Works with all existing network nfrastructure.
• Capable of up to 128-Bit WEP Encryption.
• Freedom to roam while staying connected.
• UP to 72.2Mbps High-Speed Transfer Rate in 802.11n mode of operation.
• Operating Systems: Linux, Windows
• Low power consumption.
• Easy to install and configure.
• High speed USB 2.0 interface
• ROHS compliant

Product Specification

72.2Mbps
Modulation Method| GFSK(BLE) DQPSK,DBPSK,CCK(802.11b)

QPSK,BPSK,16QAM,64QAM with OFDM (802.11g) QPSK,BPSK,16QAM,64QAM with OFDM (802.11n)

Frequency Band| 2412~2462 MHz
Operation Mode| Infrastructure
Security| WEP, TKIP, AES, WPA, WPA2
Operating Voltage| 3.3V±10%
Current Consumption| ＜750mA
Antenna Type| PCB
Operating Temperature| -20 ~ 85°C ambient temperature
Storage Temperature| -40 ~ 85°C ambient temperature
Humidity| 5 to 95 % maximum (non-condensing)

NOTICE:

• please keep this product and accessories attached to the places which children can’t touch;
• do not splash water or other liquid onto this product, otherwise it may cause damage;
• do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;
• please keep this product away from flammable or naked flame;
• please do not repair this product by yourself. Only qualified personnel can be repaired.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The module is limited to OEM installation ONLY.
The OEM integrator is responsible for ensuring that the end user has no manual instruction to remove or install the module.

• This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS). It is applicable to the modular transmitter.
• This radio transmitter FCC ID: 2AC23-WL3H has been approved by Federal Communications Commission to operate with the integrated PCB antenna. Use of any other antenna is strictly prohibited without filing an application for a new system-specific FCC ID.
• The module complies with FCC Part 15.247 and applies for Single Module approval.
• Trace antenna designs: Not applicable – the antenna is integrated into the module and cannot be modified. See section 2.3.
• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Antenna type an and antenna gain:

BT :

4G WIFI

Antenna| Frequency (MHz)| Antenna Type| MAX Antenna

Gain (dBi)

---|---|---|---
1| 2412-2462| PCB Antenna| 2.80

Note: The antenna is permanently attached and can’t be replaced.

• Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: 2AC23-WL3H” Any similar wording that expresses the same meaning may be used.

• Testing of the host product with all the transmitters installed – referred to as the composite investigation test- is recommended, to verify that the host product meets all the applicable FCC rules. The radio spectrum is to be investigated with all the transmitters in the final host product functioning to determine that no emissions exceed the highest limit permitted for any one individual transmitter as required by Section 2.947(f). The host manufacturer is responsible to ensure that when their product operates as intended it does not have any emissions present that are out of compliance that were not present when the transmitters were tested individually.
  If the modular transmitter has been fully tested by the module grantee on the required number of channels,modulation types, and modes, it should not be necessary for the host installer to re-test all the available transmitter modes or settings. It is recommended that the host product manufacturer, installing the modular transmitter, perform some investigative measurements to confirm that the resulting composite system does not exceed the spurious emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions).

• The testing should check for emissions that may occur due to the intermixing of emissions with the other transmitters,digital circuitry, or due to the physical properties of the host product (enclosure). This investigation is especially important when integrating multiple modular transmitters where the certification is based on testing each of them in a stand-alone configuration.

• Any company of the host device which installs this modular should perform the test of radiated & conducted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result complies with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally.
  The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

• The host manufacture is recommended to use D04 Module Integration Guide recommending as “best practice” RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties

• This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.

Notice to OEM integrator

• Must use the device only in host devices that meet the FCC RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• The end user manual shall include FCC Part 15 compliance statements related to the transmitter as show in this manual(FCC statement).
• The host manufacturer is responsible for compliance of the host system with the module installed with all other applicable requirements for the system such as Part 15 B.
• The host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host.
• The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual.
• This module iS stand-alone modular. If the end product will involve Multiple simultaneous transmitting conditions or different operational conditions for a stand-alone modular transmitter in a host, the host manufacturer has to consult with the module manufacturer for the installation method in the end system.
• Any company of the host device which installs this modular should perform the test of radiated & conducted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result complies with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally.
• This modular transmitter is only FCC-authorized for the specific rule parts (47CFR Part 15.247) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
• The host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host.
• Must have on the host device label showing Contains FCC ID: 2AC23-WL3H

FCC ID can not to be placed on the host and only hosts going into the US can use the FCC ID.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>