v7world CHGCT30i UV-C Cleanse and Sanitizer Kit User Manual

v7world CHGCT30i UV-C Cleanse and Sanitizer Kit

SAFETY AND WARNINGS

CAUTION: This symbol on the product indicates important literature concerning operation and maintenance. Do not remove or alter labels.
Check www.v7world.com for additional support and installation information.

• This product uses UV-C light. Warning: eye and skin damage may result from direct exposure to the light produced by these lamps. Do not activate LEDs with doors open. To safely use the UV-C LEDs kit, the system requires to always close both doors completely: left door first and then right door, closing the handle. By following this instructions, the product prevents automatically any accidental exposure.
• WARNING: UV emitted from this product. Avoid eyes and skin exposure to unshielded product.
• This product has been designed to work with cart’s doors closed. Follow installation instructions: do not change any steps of the installation or product.
• Never look at lamps while they are on, lit or illuminated.
• Disconnect power to all UV-C devices before any maintenance operation
• This product has a security system to automatically prevent accidental exposure. Do not alter this system. Do not try by any means to fake doors’ closing
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
• Caution: no changes or modifications allowed on the equipment not expressly approved by the party responsible for compliance. It could void the user’s authority to operate the equipment.
• Please refer to Charge Cart’s user manual for warnings regarding the Charge Cart itself.

FUNCTIONS

Charge Cart’s UV-C Kit is a set of 3 UV-C led bars, a specific control board and accessories. Charge Cart’s UV-C kit uses UV technology to disinfect the devices stored in the Cart.

It automatically starts the disinfection process after 30 seconds from the closure of the doors. To safely use the UVC LEDs kit, the system requires to always close both doors completely: left door first and then right door, closing the handle. UVC LEDs will be lit for 5 minutes in order to complete the disinfection process.

Prevention to accidental exposure
User must always close both doors when not operating the Charge Cart.
Whenever the user opens the cart’s doors before the disinfection process is over, UV-C LEDs are instantly turned off in order to prevent any possible direct exposure.
The process will restart with the 30 seconds countdown when closing doors.

PACKAGE INCLUDES

INSTALLATION

CAUTION: It is mandatory to apply the safety label provided in the box. Position the label as shown in the image below.

Make sure to position the label centered.
Ensure it is readable from the front side, where the user will load devices.

To install UV-C kit, the user needs to remove each drawer. Pull the drawer completely out: this allows the user to can find levers to remove the drawer from the cart. Find levers at the side of the slide.

Once removed, UV-C LEDs can be installed. Spot the position to fix UV-C bars in the fig 1.

The cable connected to the UV-C LEDs shall pass to the rear side of the cart via the internal openings on the side of the cart (highlighted in fig 2).

Installation of the Tamper in the in the front door:

• Place the nut in its support (behind the magnet)
• Slide the magnet in the opening
• Insert screws through the holes in the lateral part of the door and fix it

Remove the frontplate with power led indicators by unscrewing the four screws (see circles in the figure 3). Unplug the inner connector and remove the frontplate.

Slide the metal part of the “tamper cable” underneath all cablings of the frontplate. Once in position, turn the frontplate upside-down and fix the tamper with screws.

Move the tamper cable to the rear side of the cart.
To do so, remove the frontplate on the rear part of the cart by unscrewing the four screws (see circles in figure 4).

Remove the rear frontplate and proceed with the installation of the UV-C box support. Position it facing the outside (1) and turn it upside-down, then attach it with screws (2).

ATTENTION: Make sure to install the UV-C Box support to the hole that will be positioned on the left when repositioning the frontplate.

Pass the “tamper cable” through the holes positioned in top-corners pushing it via the openings (highlighted below) so that the cable pin will be in the rear side of the cart.

Now assemble the frontplate back in its original position by plugging the connector and usign screws to fix it.

Installation of the UVC box:

• Position UV-C box in the left part of the rear frontplate, paying attention to the cablings. Make sure to tie the tamper cable up and that the UV-C box flaps are positioned under the cable.
• Fix the box with the lateral screws and plug the connector coming from the “tamper cable” to the board

Place the rear frontplate in its original position and use screws to attach it.
Once everything is correctly installed, the rear side of the cart is like this.

Link the cable coming from UV-C LEDs to the box with this pattern:

USA
Ingram Micro Inc.
3351 Michelson Dr. Suite 100
Irvine, CA 92612, USA

Canada
Ingram Micro, LP Canada
55 Standish Court
Mississauga, ON, L5R 4A1, Canada Mexico
Ingram Micro Mexico, S.A. de C.V.
Calle de Joselillo 3, El Parque, 53398 Naucalpan de Juárez, CDMX, Mexico

United Kingdom
Ingram Micro (UK) Ltd,
CBXII West, Midsummer Boulevard, Milton Keynes, MK9 2EA, United Kingdom

Europe
Ingram Micro Pan Europe GmbH Heisenbergbogen 3, D-85609 Dornach / Munich, Germany

New Zealand
Ingram Micro NZ Ltd
78 Apollo Drive, Albany
Auckland 0642, New Zealand

India
Ingram Micro India Limited
Godrej IT Park, B-Block, 5th Floor Pirojsahanagar, L.B.S. Road,
Vikhroli (West), Mumbai-400 079, India

Australia
Ingram Micro Pty Ltd
61 Dunning Ave, Rosebery
NSW 2018, Australia

Brazil
Ingram Micro Brasil Ltda
Av. Francisco Matarazzo, 1500 – Torre NY Sao Paulo, SP 05001-100, Brazil

Hong Kong
Ingram Micro (China) Limited
Room 1205-18, 12/F, Tower 1,
Millennium City,
388 Kwun Tong Road, Kowloon, Hong Kong

RECOMMENDATIONS FOR DISPOSAL
Correct disposal of the WEEE product (waste from electrical and electronic equipment)

The symbol shown on the product, on the accessories and on the documentation (Fig.1) indicates that the product and its electronic accessories (such as cables, adapters, electrical parts in general) must not be disposed of with other unsorted waste at the end of their life cycle.
To avoid any damage to the environment, the user is invited to separate the product and the aforementioned accessories from other types of waste. The user company will be responsible for arranging the collection of waste and managing the steps necessary for proper disposal.
IMECON S.r.l. as a manufacturer it is duly registered in the Register of Manufacturers of Electrical and Electronic Equipment with registration IT20110000012577.

www.v7world.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>