Schneider WDE002906 Electric Wiser Exxact Battery Instruction Manual

: June 6, 2024
: Schneider

Table of Contents

For your safety
Prerequisites
Additional system information
Getting to know the product
Package contents
Mounting the device
Setting the device
Troubleshooting
Technical data
Schneider Electric Industries SAS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Schneider WDE002906 Electric Wiser Exxact Battery Instruction Manual

For your safety

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

Safe electrical installation must be carried out only by skilled professionals. Skilled professionals must prove profound knowledge in the following areas:

Connecting to installation networks
Connecting to several electrical devices
Laying electrical cables
Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in death or serious injury.

Prerequisites

Download the Wiser app to your smartphone and install the Wiser Gateway to configure and control Wiser devices.
App Download

Additional system information

Detailed product information is available online in the system user guide: Scan the QR code or follow the link.
https://www.productinfo.schneider-electric.com/wiser_eu/

Getting to know the product

The Free Located Wireless Switch 1-gang/ 2-gang (hereinafter referred to as device) is used to control a group of Zigbee devices within the same Zigbe network.

The device can be configured through the Wiser app or can be paired with other Wiser Zigbee devices.

To use the device in your home through the Wiser app, you will need the Wiser Gateway.

Package contents

A Free Located Wireless Switch 1-gang / Free Located Wireless Switch 2-gang
B Screws: 2 × ST Z.3 × 20 mm with wall plug
C Battery
D Adhesive pads
E Adhesive silver foil
F Installation instructions

The frame and wall box are not included in the package. They must be procurred by the user

Mounting the device

Inserting the battery

WARNING

CHEMICAL BURN HAZARD

Keep batteries out of reach of children. If swallowed, seek immediate medical attention.

Failure to follow these instructions can result in serious injury or death.

NOTICE

EQUIPMENT DAMAGE

The module is locked on the fixing plate with retaining claws. Never pull the module before sliding it upwards.

Failure to follow these instructions can result equipment damage.

Remove the module by sliding it upwards.
Rotate the module by 180° to access the battery cover.
Press and hold the battery cover with your thumb.
Slide the battery cover with another thumb to remove.
Insert the battery with plus (+) symbol facing outward.
Secure the battery cover.

The battery cover is designed with child lock protection.

Mounting using screws

G Fixing plate
H Frame
I Module
For wall box, wood or wall use mounting screws.
The minimum distance to walls/edges above and below the device must be approx. 7 mm.
For smooth surface, use adhesive pads.
For glass surface, use adhesive pads and adhesive silver foil.
While mounting the device, the arrows on the fixing plate must point upwards.

Note: Do not install the device on a metal surface, as it affects the wireless communication and performance of the device.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

While installing the device on a wall box or an existing switch outlet combination, always isolate the 230 VAC cables by applying an adhesive silver foil on the fixing plate.

Failure to follow these instructions will result in death or serious injury.

Cut the adhesive silver foil to a size of 55 × 55 mm and then paste it on the rear side of the fixing plate.
Secure the fixing plate on the wall box using screws.
Insert the module into the frame from the front and ensure that it clicks into place.
Mount the device on the fixing plate and make sure that it is firmly secured.

Mounting using adhesive pads

Affix the adhesive pads on the rear side of the fixing plate.
Mount the device on the surface.

Mounting using adhesive silver foil

**** Affix adhesive pads to the fixing plate.

Paste the adhesive silver foil on the surface, avoiding bubbles or folds in the foil.
Mount the device on the adhesive silver foil.

Replacing the battery

**** If the battery is low (< 10%) the status LED blinks red once, when a push button is pushed.
Do not remove the module from the frame. The battery can be replaced when the module and frame are in assembled state.
Dispose used batteries, as per statutory regulations.

Setting the device

Connecting to the Wiser Gateway

Short press (< 0,5 s) the push button 3 times to connect to an available Zigbee network. The status LED blinks amber and then turns green upon successful connection to the Zigbee network.

Resetting the device

Short press (< 0,5 s) the push button 3 times and then press and hold the push button (> 10 s), the status LED blinks red. Then release the push button, the status LED stops blinking upon successful reset of the device.

The device restarts and blinks green for a few seconds. After reset, the LED turns off to save the battery.

**** After the device is reset, all the programming and network data will be deleted.

Troubleshooting

Refer to the system user guide.

Technical data

Battery

|

CR2032

---|---

Battery life

| Up to 5 years (depending on frequency of use and quality of battery)
IP rating|

IP20

Operating frequency

| 2405-2480 MHz
Max. radio- frequency power transmitted|

< 10 mW

Range

| 100 m open space
Operating temperature|

-5 °C to 45 °C

Relative humidity

| 10% to 95%
Certification|

Zigbee 3.0

Dispose of the device separately from household waste at an official collection point. Professional recycling protects people and the environment against potential negative effects.

Trademarks

Wiser™ is a trademark and the property of Schneider Electric SE, its subsidiaries and affiliated companies.
Zigbee ® is a registered trademark of the Zigbee Alliance.
Apple ® and App Store ® are brand names or registered trademarks of Apple Inc.
Google Play ™ Store and Android ™ are brand names or registered trademarks of Google Inc.

Other brands and registered trademarks are properties of their relevant owners.

EU Declaration of conformity

Hereby, Schneider Electric Industries, declares that this product is in compliance with the essential requirements and other relevant provisions of RADIO EQUIPMENT DIRECTIVE 2014/53/EU. Declaration of conformity can be downloaded on: se.com/docs.