VAREX WUBT-236ACN 2T2R Wi-Fi USB Module Instruction Manual
- June 6, 2024
- VAREX
Table of Contents
**WUBT-236ACN 2T2R Wi-Fi USB Module
Instruction Manual**
Support Multiple Operation Systems (Android/Linux/Windows)
Varex Imaging Corporation WUBT-236ACN(BT)[MN] is a highly integrated single-
chip Wireless LAN (WLAN). It is integrated 2T2R WLAN MAC, baseband, and dual-
band RF in a single chip. WUBT-236ACN(BT)[MN] provides a cost-effective
solution for M2M (machine to machine) connectivity product/device by one USB
port, it can be easily integrated into the most familiar operation system
Android/Linux/Windows).
802.11ac/a/n 2T2R Wifi USB Module with various USB input formats & internal
printing or external RF antenna connector for high-performance wireless LAN
device. It is designed to provide a completely M2M connection & excellent cost
performance with low power consumption and enhance the advantages of robust
systems & applications.
Embedded Application
Applications include portable handheld devices, thin client computers, medical devices, network security & monitoring, 3D printer, TV, STB, POS, digital signs, gaming machines, robotic machinery, industrial tablets, etc.
Key Feature
- 802.11ac/a/an Wi-F
- Support 802.11ac 2×2, compliant with MU-MIMO
- Maximum data rates: 300Mbps in 802.11n, 866.7Mbps in 802.11ac.
Specification
| Standards | IEEE 802.11ac/a /an(2T2R) |
|---|---|
| Chipset | Realtek RTL88228U-CG |
| Data Rate | 802.11a:54Mbps 802.11n:MCS0-15 802.11ac: MCS0-9 |
| Operating Frequency | FCC & IC: 5.15-5.25 GHz, 5.725-5.85 GHz Japan: 5.15-5.25 |
GHz
Subject to local regulations
Interface| WLAN: USB
Antenna| ANTO for WLAN lla only, ANTO+ ANT1 for WLAN 11 an/ac
Modulation| Wi-Fi :
802.11n: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11a: OFDM (BPSK, QPSK, 16-QAM,
64-QAM) 802.11ac: OFDM (BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM)
Power Consumption| TX mode: 450Ma(Max.) RX mode: 250mA(Max.)
Operating Voltage| DC 5V
Operating Temperature Range| -20°C”70°C
Storage Temperature Range| -40°C-80C
Humidity (Non-Condensing)| 5%-95% (Operating) 5%-90% (Storing)
Security| 64/128-bits WEP, WPA, WPA2, 802.1x
Block Diagram
| Pin | Description |
|---|---|
| Pin_1 | USB 5V |
| Pin_2 | USB D- |
| Pin_3 | USB D+ |
| Pin_4 | USB GND |
| LED | WiFi LED |
| Ant_0 | RF Antenna for WLAN 11a |
| Ant_0 + Ant_1 | RF Antenna for WLAN 11 an/ac |
Federal Communication Commission Interference Statement:
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
This module limit can be used to install in the host below:
Product name: Digital Image Receptor
Model: 4336W-G5
RF exposure statements
The product complies with the FCC portable RF exposure limit set forth for an
uncontrolled environment and is safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
These requirements set a SAR limit of 1.6 W/kg averaged over one gram of
tissue. The highest SAR value reported under this standard during product
certification for use when properly worn on the body is 1.319 W/kg.
CFR 47 FCC PART 15 SUBPART B and SUBPART E have been investigated. It is
applicable to the modular transmitter.
Any company of the host device which installs this modular with limited
modular approval should perform the test of radiated & conducted emission and
spurious emission, etc. according to FCC part 15E: 15.407 and 15B Class A
requirement, Only if the test result comply with FCC part 15E: 15.407 and 15B
Class A requirement， then the host can be sold legally.
The devices must be installed and used in strict accordance with the
manufacturer’s instructions as described in the user documentation that comes
with the product.
We will retain control over the final installation of the modular such that
compliance with the end product is assured. In such cases, an operating
condition on the limit modular approval for the module must be only approved
for use when installed in devices produced by a specific manufacturer. If any
hardware modifies or RF control software modifications will be made by the
host manufacturer, C2PC or a new certificate should be applied to get
approval, if those changes and modifications made by the host manufacturer are
not expressly approved by the party responsible for compliance , then it is
illegal.
This radio transmitter ZZ6-WUBT236ACNBT has been approved by Federal
Communications Commission to operate with the antenna types listed below, with
the maximum permissible gain indicated. Antenna types not included in this
list that have a gain greater than the maximum gain indicated for any type
listed are strictly prohibited from use with this device.
Unique antenna connector (Hirose U.FL) must be used on Part 15 authorized
transmitters used in the host product.
Antenna
Type| Antenna Model| Maximum Gain (dBi)| Remark
---|---|---|---
5GHz
PCB Antenna| XRpad CBSA
P/N: 45524302| 5.9 dBi|
If the FCC identification number is not visible when the module is installed
inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter
Module FCC ID: ZZ6-WUBT236ACNBT” Or “Contains FCC ID: ZZ6-WUBT236ACNBT”
The modular transmitter is only FCC authorized for the specific rule parts
(i.e., FCC transmitter rules) listed on the grant, and the host product
manufacturer is responsible for compliance to any other FCC rules that apply
to the host not covered by the modular transmitter grant of certification. The
final host product still requires Part 15 Subpart B compliance testing with
the modular transmitter installed.
Industry Canada statement:
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numèrique de la classe A est conforme á la norme NMB-003 du
Canada
Caution:
- The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
- For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-topoint and non-point-to-point operation as appropriate; and Avertissement:
Radiation Exposure Statement:
These requirements set a SAR limit of 1.6 W/kg averaged over one gram of
tissue. The highest SAR value reported under this standard during product
certification for use when properly worn on the body is 1.319 W/kg.
Standard as below:
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
This radio transmitter (IC: 9909A-UBT236ACNBT has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
| Antenna Type | Antenna Model | Maximum Gain (dBi) | Remark |
|---|
5GHz
PCB Antenna| XRpad CBSA
P/N: 45524302| 5.9 dBi|
If the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 9909A- UBT236ACNBT”.
Manual Information To the End User:
The OEM integrator has to be aware not to provide information to the end-user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module. The end-user manual shall include
all required regulatory information/warning as shown in this manual.
The end-user manual shall include FCC Part 15 /ISED RSS GEN compliance
statements related to the transmitter as shown in this manual.
Host manufacturer is responsible for compliance of the host system with the
module installed with all other applicable requirements for the system such as
Part 15 B, ICES 003.
The host manufacturer is strongly recommended to confirm compliance with
FCC/ISED requirements for the transmitter when the module is installed in the
host.
Must have on the host device a label showing Contains FCC ID:
ZZ6-WUBT236ACNBT, Contains IC: 9909AUBT236ACNBT
The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual.
If the end product will involve Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer has to consult with the module manufacturer for the installation method in end system.