Shark VACMOP RV2000WD Robot Floor Cleaner User Guide

RV2000WD Robot Floor Cleaner

VACMOPTM Wet/Dry Robot Floor Cleaner Robot nettoyant pour les planchers
RV2000WD Series · Série · Serie
OWNER’S GUIDE GUIDE DE L’UTILISATEUR

IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ CAREFULLY BEFORE USE · FOR HOUSEHOLD USE ONLY
If the charging cable plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT force into outlet or try to modify to fit.

WARNING
To reduce the risk of fire, electric shock, injury, or property damage:

GENERAL WARNINGS When using an electrical appliance, basic precautions should always be followed, including the following: 1. This appliance consists of a Wet/
Dry Robot Floor Cleaner vacuum and charging dock with power supply. These components contain electrical connections, electrical wiring, and moving parts that potentially present risk to the user. 2. Before each use, carefully inspect all parts for any damage. If a part is damaged, discontinue use. 3. Use only identical replacement parts. See replacement accessories page of this booklet. 4. This Wet/Dry Robot Floor Cleaner contains no serviceable parts. 5. Use only as described in this manual. DO NOT use Wet/Dry Robot Floor Cleaner for any purpose other than those described in this manual. 6. With exception of filters, dust cups and pads, DO NOT expose any parts of the Wet/Dry Robot Floor Cleaner to water or other liquids.
USE WARNINGS 7. This appliance can be used by persons
with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
a) Children shall not play with the appliance.
b) Cleaning and user maintenance shall not be made by children without supervision.
8. Always turn off the robotics vacuum cleaner before inserting or removing the filter, dust bin, or fluid reservoir.
9. DO NOT handle plug, charging dock, charging cable, or Wet/Dry Robot Floor Cleaner with wet hands. Cleaning and user maintenance shall not be made by children without supervision.

10. DO NOT use the robot without the dust bin, filter, and fluid reservoir in place.
11. DO NOT damage the charging cord: a) DO NOT pull or carry charging dock by the cord or use the cord as a handle. b) DO NOT unplug by pulling on cord. Grasp the plug, not the cord. c) DO NOT close a door on the cord, pull the cord around sharp corners, or leave the cord near heated surfaces.
12. DO NOT put any objects into nozzle or accessory openings. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
13. DO NOT use if Wet/Dry Robot Floor Cleaner airflow is restricted. If the air paths become blocked, turn the vacuum cleaner off and remove all obstructions before turning on the unit again.
14. Keep all vacuum openings away from hair, face, fingers, uncovered feet, or loose clothing.
15. DO NOT use if Wet/Dry Robot Floor Cleaner is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water.
16. DO NOT place vacuum cleaner on unstable surfaces,
17. If robot is placed in a room, and it is not starting from the dock, the robot must be placed in an unobstructed circle of 1.5 ft. (45 cm) away from edges and cliffs.
18. DO NOT use to pick up: a) Liquid spills b) Large objects c) Hard or sharp objects (glass, nails, screws, or coins) d) Large quantities of dust (drywall dust, fireplace ash, or embers). DO NOT use as an attachment to power tools for dust collection. e) Smoking or burning objects (hot coals, cigarette butts, or matches) f) Flammable or combustible materials (lighter fluid, gasoline, or kerosene) g) Toxic materials (high concentrations of chlorine bleach liquid, high concentrations of ammonia, or drain cleaning solution)

sharkclean.com

19. DO NOT use in the following areas: a) Outdoor areas near fireplaces with unobstructed entrances b) Spaces that are enclosed and may contain explosive or toxic fumes or vapors (lighter fluid, gasoline, kerosene, paint, paint thinners, mothproofing substances, or flammable dust c) In an area with a space heater d) Near fireplaces with unobstructed entrances
20. Turn off the Wet/Dry Robot Floor Cleaner before any adjustment, cleaning, maintenance or troubleshooting. Note: in the OFF (O) position, the robot still uses a small amount of power.
21. Allow all filters to air-dry completely before replacing in the Wet/Dry Robot Floor Cleaner to prevent liquid from being drawn into electric parts.
22. DO NOT modify or attempt to repair the Wet/Dry Robot Floor Cleaner or the battery yourself, except as indicated in this manual. DO NOT use the vacuum if it has been modified or damaged.
23. Remove all spilled or leaked liquid from the dock landing mat, base or floor, as it could lead to risk of electrical shock.
24. Try on an inconspicuous small area of the floor, a little bit of the VACMOPTM cleaning solution to ensure it does not affect the floor.
25. When refilling the reservoir, check for leaks, as pooled liquids are a slipping hazard and may cause electrical shock. If the reservoir is damaged, it must be replaced.
26. Use caution walking on mopped floors, as they may be slippery while damp.
27. For your robot’s cliff sensors to work properly, all runners, rugs, or carpets must be 8 inches away from any stairs (or it must be continuous and extend over the edge of the stairs). If a runner, rug, or carpet edge that is less than 8 inches from the stairs cannot be moved, use a BotBoundary® strip to block off the stairs. BotBoundary strips are not included with your robot.
BATTERY USE 28. The battery is the power source for
the vacuum. Carefully read and follow all charging instructions. 29. To prevent unintentional starting, ensure the vacuum is powered off before picking up or carrying the vacuum. DO NOT carry the appliance with your finger on the power switch.

30. Use ONLY the Shark® charging dock XDCKRV2000 and use only battery RVBAT850A. Use of batteries or battery chargers other than those indicated may create a risk of fire.
31. Keep the battery away from all metal objects such as paper clips, coins, keys, nails, or screws. Shorting the battery terminals together increases the risk of fire or burns.
32. Under abusive conditions, liquids may be ejected from the battery. Avoid contact with this liquid, as it may cause irritation or burns. If contact occurs, flush with water. If liquid contacts eyes, seek medical help.
33. Robotic vacuum cleaner should not be stored, charged, or used at temperatures below 50°F (10°C) or above 104°F (40°C). Ensure the battery and vacuum have reached room temperature before charging or use. Exposing the robot or battery to temperatures outside of this range may damage the battery and increase the risk of fire.
34. DO NOT expose the Wet/Dry Robot Floor Cleaner or battery to fire or temperatures above 265°F (130°C) as it may cause explosion.
35. Non-rechargeable batteries cannot be recharged.
BOTBOUNDARY® STRIPS 36. DO NOT put BotBoundary strips
underneath carpet or rugs. 37. DO NOT place BotBoundary strips on
top of one another. 38. Always use BotBoundary strips around
reflective flooring and surfaces. 39. BotBoundary strips should always be
used near carpeted stairs. 40. DO NOT place BotBoundary strips within
10 feet of the dock. 41. For your robot’s cliff sensors to work
properly, all runners, rugs, or carpets must be eight inches from any stairs (or it must be continuous and extend over the edge of the stairs). If a runner, rug or carpet edge that is less than eight inches from the stairs cannot be moved, you must use a BotBoundary strip to block off the stairs.

SAVE THESE INSTRUCTIONS
For the latest warnings and cautions, go to sharkclean.com/robothelp
sharkclean.com

GETTING TO KNOW YOUR SHARK® AI ROBOT VACMOPTM

Error Indicator Light

Charge Indicator Lights

Wi-Fi Indicator Light

Front Bumper Clean Button

Dock Button
Mopping Indicator Light

Fluid Reservoir

Power Button

Side Brush Battery Door Self-Cleaning Brushroll
sharkclean.com

Cliff and Boundary Sensors
Charging Contact Front Caster Wheel
Drive Wheel Brushroll Door
Dust Bin and Filter

GETTING TO KNOW YOUR SHARK® AI ROBOT VACMOPTM
FLUID RESERVOIR

Removal Buttons

Fill Port

Pad Slot

DOCK FRONT

Charging Dock

DOCK BOTTOM

Charging Contacts

Charger Cord Wrap

DOCK LANDING MAT (This side up)

sharkclean.com

DOCK SETUP

CHARGING
IMPORTANT: The Shark® AI Robot VACMOPTM has a pre-installed rechargeable battery. Charge the battery completely before first use. It may take up to 6 hours to fully charge.

3 ft. 3 ft.
5 ft.

· Select a permanent location with strong Wi-Fi for the Charging Dock, because every time you relocate it, your robot will have to completely re-map your house.
· Place the dock with its back against a wall and attach the landing mat. Select a level surface on bare floor, in a central area. Do not place dock against baseboards or heating elements.
· Remove any objects that are closer than 3 feet from either side of the dock, or closer than 5 feet from the front of the dock.
· Plug in the dock. The indicator light will illuminate green when the dock has power.

To charge, place the robot on the dock. The Power button on the side of the robot must be in the ON position (I). The robot will beep when charging begins and the charging indicator on the dock will turn from green to blue.

When the cleaning cycle is complete, or if the battery is running low, the robot will search for the dock. If the robot doesn’t return to dock, its charge may have run out, or if it is in wet cleaning mode, the dock may be blocked by carpet.

INSTALLING THE SIDE BRUSHES
Snap the 2 included Side Brushes onto the square pegs on the bottom of the robot.

sharkclean.com

If the robot has no charge or it cannot return to the dock, manually place it on the dock. The indicator light will turn blue and the robot will beep when it is correctly placed on the dock.
NOTE: When manually placing the robot on the dock, make sure the Charging Contacts on the bottom of the robot are touching the ones on the dock. While the robot is charging, both white LED lights will flash. When charging is complete, both white lights will illuminate steadily. NOTE: When picking up the robot, be careful not to place fingers between the bumper and the base of the robot.
sharkclean.com

CHARGE INDICATOR LIGHTS

In Use
While Charging (White)

Full Charge (White)

Partial Charge (White)

Low Charge (Red)

No Charge or Off
The white charge indicator lights show how much battery power is remaining.
While the robot is charging, both white LED lights will flash. When charging is complete, both white lights will illuminate steadily. It may take up to 6 hours to fully charge your robot.
If the robot is idle and away from the charging dock for 10 minutes, it will enter Sleep Mode. The indicator lights will turn off, but the battery and Wi- Fi lights will remain on in sleep mode. Wake up the robot by pressing any button.

NOTE: If the low charge light is blinking red, there is not enough battery power for the robot to return to the dock. Manually place the robot on the dock.
TIP: To preserve battery life, turn off the power switch if the robot will not be used for a long period of time. The robot should be recharged at least once every three months. The switch must be in the ON position to charge the robot.

IMPORTANT: Before cleaning an entire room for the first time, we recommend that you first test your robot on a small section of the floor to ensure there is no scratching.
sharkclean.com

BUTTONS AND INDICATOR LIGHTS
CLEAN BUTTON Press to begin a cleaning session. Press again to stop.

DOCK BUTTON Press to stop cleaning and send robot back to the charging dock.
CHARGE INDICATOR LIGHTS Display the amount of charge remaining in the battery.

RECHARGE & RESUME Press and hold the CLEAN button for 15 seconds to turn Recharge & Resume ON or OFF.
The Recharge & Resume function is turned OFF by default. Turn ON Recharge & Resume for complete coverage if your home’s floor plan is bigger than 1500 sq. ft. Your robot will return to the dock, recharge, and can pick up where it left off.

WET MOPPING INDICATOR LIGHT Illuminates when fluid reservoir is properly installed. Droplet icon will turn red if there is no fluid in the reservoir. After 15 minutes, the robot will return to dock if reservoir is not filled.
“!” ERROR INDICATOR See Troubleshooting section for full list of error codes.
WI-FI INDICATOR White light: connected to Wi-Fi. Red light: not connected. Flashing White: setup mode. No light: not set up yet.

sharkclean.com

PREP YOUR HOME
Your robot uses an array of sensors to navigate around walls, furniture legs, and other obstacles while it cleans. To prevent the robot from entering areas you don’t want it to, set up no-go zones in the app. For best results, prepare your home as indicated below, and schedule a daily cleaning to ensure all floor areas are regularly maintained.

NOTE: Scheduling is one of numerous features that can only be done in the app.
OBSTRUCTIONS Clear cords and small objects less than 2.8″ in height, and open interior doors to ensure a complete map of your home.

SCHEDULING Schedule whole-home cleanings with the app. To schedule a mopping run with the app, the reservoir must be filled and installed in the robot with the pad attached.

USING THE SHARK® AI ROBOT VACMOPTM IQ NAVIGATIONTM AND AI LASER VISION

THRESHOLDS Your robot can climb over most thresholds to get from room to room, but if one is too high, set up a no-go zone in the app to block it off.
STAIRS Your robot’s cliff sensors will prevent it from falling off ledges. For the cliff sensors to work properly in any mode, all runners, rugs, or carpets must be at least 8 inches from any stairs, or must extend over the edge of the stairs.

AVOID MOVING THE ROBOT & DOCK While your robot is cleaning, do not pick it up and move it, or move the charging dock– this will impact the robot’s navigation and ability to return to dock when cleaning is complete.
REMOVE RUGS FROM DOORWAYS WHEN MOPPING Before mopping, you must set up Carpet Detection in the app, and move any carpets or rugs that block access to floors that you want your robot to mop.

After setup is complete, follow instructions in the app to help your robot conduct an Explore Run to create an initial map of your home.
The robot will travel from room to room to identify walls, furniture, and other obstacles as it cleans. This run will take less time than a full cleaning, as it doesn’t cover the entire floor.

The robot’s object detection technology helps it navigate around obstacles taller than 2.8″ in height. Clear away small objects that may interfere with the cleaning path of your robot.
Create no-go zones in the app to block off areas you do not want the robot to enter. You can set up no-go zones around small objects, or use them to block off large areas.

VACUUM ONLY INSTRUCTIONS

MANUAL CLEANING MODE
To manually start a cleaning cycle, press the Clean button on the robot or on the mobile app. To immediately send the robot back to the dock, press the Dock button.
IMPORTANT: Before cleaning an entire room for the first time, we recommend that you first test your robot on a small section of the floor to ensure there is no scratching.
sharkclean.com

To vacuum, the fluid reservoir must NOT be attached to the robot. Make sure the dust bin is properly installed.

NOTE: Be sure to charge the robot completely before its first cleaning so that it can explore, map, and clean as much of your home as possible. It may take up to 6 hours to fully charge your robot. NOTE: Avoid moving the dock. If it is relocated, the robot may not be able to find its way back to the dock. If the robot is relocated while in use, it may not be able to follow its intelligent cleaning path, or find its way back to the dock.
sharkclean.com

USING THE SHARK® AI ROBOT VACMOPTM
WET MOPPING SETUP
NOTE: Before it can mop, the robot MUST complete its Explore Run and an initial vacuuming run, and Carpet Detection must be set up in the app.

USING THE SHARK® AI ROBOT VACMOPTM WET MOPPING SETUP

Attach the mop pad by inserting the flat edge of the pad through the slot in the reservoir. Pull the mop pad all the way through the slot until it is securely inserted.

Secure the pad to the back of the reservoir.

When the reservoir has fluid and is properly installed, with the mop pad attached, the robot is ready to vacuum and mop simultaneously. Press the Clean button on the robot or in the app to start a vacuuming and mopping run. The robot will prime the mop pad for 30 seconds before starting its run.

When mopping is complete, remove the reservoir by pressing both buttons and sliding it out. Empty the reservoir after each use.
CAUTION: Floors may be slippery after mopping.

Lift open the fill cap on the top of the reservoir. Fill with VACMOP cleaning solution, or room temperature water, to the MAX fill line. Close the cap and make sure it is properly sealed.

Firmly push the reservoir into the back of the robot, behind the dust bin, and ensure both latches click into place. The water droplet icon on the robot will illuminate white when the reservoir is inserted properly.

sharkclean.com

To remove the mop pad from the reservoir, detach the pad from the back of the reservoir and slide the pad out of the slot.
NOTE: When mopping, your robot may travel over floor mats or rugs. Before the next mopping run, move rugs or mats out of the robot’s path, or use the app to enable Carpet Detection or to set up no-go zones.

Before your robot’s first mopping run, set up Carpet Detection in the app. This ensures your robot will avoid carpets and rugs when mopping. Follow the instructions in the app to help the robot complete its Explore Run, and then an initial vacuuming run. Once the robot completes these runs, it will create a map in the app, and you can select other areas for the robot to avoid when mopping.
sharkclean.com

USING THE SHARK® AI ROBOT VACMOPTM

Please visit sharkclean.com/app or call 1-855-460-5425 for answers to all your app questions.

USING THE SHARKCLEANTM APP AND VOICE CONTROLS

Get the most out of your Shark AI Robot VACMOP with these app features:

· Recharge and Resume

Enable this feature to handle

multi-room cleaning in larger

homes. The robot will return

Living Room

Kitchen

Dining Room

to the dock, recharge, and can pick up where it left off.

· Carpet Detection Once the robot has mapped your home, activate Carpet Detection in the app to identify carpets and rugs for the robot to avoid when it mops.

· Scheduling Set whole-home cleanings for any time, any day.
· Control From Anywhere Wherever you are, you’re in control of your robot.
· Cleaning Reports Each time your robot cleans, your app will generate a cleaning report.

Search for SharkClean in the app store and download the app to your iPhoneTM or AndroidTM.

SETTING UP VOICE CONTROL WITH THE GOOGLE ASSISTANT OR AMAZON ALEXA
Visit sharkclean.com/app for setup instructions which include how to enable Shark Skill for Amazon Alexa and using with Google Assistant.

Google Assistant:

Amazon Alexa:

“OK Google, tell Shark to start cleaning.”
“OK Google, tell Shark to pause my robot.”
“OK Google, tell Shark to send my robot to the dock.”

“Alexa, tell Shark to start cleaning.”
“Alexa, tell Shark to pause my robot.”
“Alexa, tell Shark to send my robot to the dock.”

WI-FI TROUBLESHOOTING

· To use the app, your phone must be connected to a 2.4GHz network. The app will only work on a 2.4GHz network.
· Typical home Wi-Fi networks support both 2.4GHz and 5GHz.

· Do not use a VPN or a proxy server.
· Make sure Wi-Fi isolation is turned off on the router.
· If you cannot connect, call 1-855-460-5425.

ERROR CODE
! (RED) + Wi-Fi indicator (RED Flashing) ! (Flashing red) + Wi-Fi (RED) Wi-Fi (RED Flashing)

PROBLEM
Wrong password for Wi-Fi SSID cannot be found, try connecting again Cannot connect to Wi-Fi

sharkclean.com

MAINTENANCE
CAUTION: Turn off power before performing any maintenance. NOTE: Even when the switch is in the OFF (O) position, the robot still uses a small amount of power.
EMPTYING THE DUST BIN

With the fluid reservoir removed, press the Dust Bin Release Button and slide out the dust bin.

To open the dust bin lid, press and hold the button while lifting the lid, using the finger slots.

Empty debris and dust into trash. Wash dust bin if necessary, using water only.
NOTE: Make sure to insert the dust bin completely, until it clicks into place.

To avoid mold, clean the area between the filter and the plastic shield after every mopping run, and periodically after vacuuming. Remove the shield and clear any debris buildup with a dry cloth or soft brush.
sharkclean.com

MAINTENANCE
CLEANING AND REPLACING THE FILTER
For optimal suction power, after each use, clean and reinsert the filter inside the robot’s dust bin. See sharkaccessories.com for replacement filters.

MAINTENANCE
SELF-CLEANING BRUSHROLL
The Self-Cleaning Brushroll actively removes hair wrap while your robot cleans. If some debris remains wrapped around the brushroll, continue to run the robot to give the brushroll time to clean itself. If some hair wrap or debris remains after continued cleaning, carefully remove it from the brushroll.

Remove and empty the dust bin. Clean any hair or debris off the Anti-Tangle Comb on the back of the dust bin.

Pull filter out of the dust bin by the tabs.

To access the brushroll, push up on the tabs on the brushroll door, then lift off the door.

Lift out the brushroll and remove any debris.
Reinstall the brushroll, inserting the flat end first. Close the brushroll door and press down until both sides click into place.

NOTE: Replace brushroll every 6 to 12 months, or when visibly worn. See sharkaccessories.com for replacement parts.
MAINTAINING THE RESERVOIR AND MOPPING PAD

Lightly tap the filter to remove debris every time you empty the dust bin. For a deeper clean, rinse the filter with water once a month. Allow the filter to air-dry for up to 24 hours before reinstalling. Do not use soap or scrub the filter. This will damage the material.

Reinsert the filter into the dust bin, then slide the dust bin back into the robot until it clicks into place.

NOTE: Replace the filter once a year for optimal performance.

sharkclean.com

To clean pads, machine wash warm with light colors. Use mild detergents and do not use bleach or fabric softeners. Air-dry, or tumble-dry on low with no dryer sheets.

Empty the reservoir after each use. Rinse the reservoir and let it air-dry. DO NOT put the reservoir in the dishwasher.

NOTE: Before storing, make sure the reservoir and pad are completely dry. Store the reservoir and pad in a dry place to prevent damage.
sharkclean.com

MAINTENANCE
CLEANING SENSORS AND CHARGING CONTACTS
CLEAN SENSORS AND CHARGING CONTACTS AS NEEDED. With a dry cloth, gently dust off the sensors and contacts located on the bottom of the robot and on the dock.

MAINTENANCE
CLEANING THE WHEELS
CLEAN FRONT WHEEL PERIODICALLY. See sharkaccessories.com for replacement parts.

IMPORTANT: The robot uses cliff sensors to avoid stairs and other steep drops. Sensors may work less effectively when they are dirty. For best results, clean sensors regularly.

CLEANING SIDE BRUSHES

CLEAN SIDE BRUSHES AS NEEDED.

Carefully unwind and remove any string or hair wrapped around brushes.
Gently wipe brushes with a dry cloth. To reinstall, snap the brushes over the pegs. Spin the brushes manually to make sure they are installed correctly.

Clean the wheel housing. NOTE: Brush not included.

Periodically clean the drive wheels and the housing around them. To clean, rotate each drive wheel while dusting.

NOTE: Remove and replace any side brushes that are bent or damaged. To remove a brush, lift it off its peg.
sharkclean.com

sharkclean.com

REPLACEMENT PARTS

Filter XFRV2000WD

Robot Dust Bin 118KY2000W

Brushroll 127KY2000

Battery RVBAT850A

Brushroll Door 121KY2000W

Side Brushes 102KY1000

Charging Dock XDCKRV2000

Dock Landing Mat 120KY2000W

Mop Pad 2-Pack PADRVWD02

Fluid Reservoir 122KY2000W

Shark® VACMOPTM Multi-Surface Cleaner Refill 2L Bottle

Shark® VACMOPTM Hardwood Cleaner Refill 2L Bottle

NOTE: To order replacement parts, filters, and cleaning solution refills, visit sharkaccessories.com.
sharkclean.com

MAINTENANCE

CAUTION: Turn off power before performing any maintenance.

TROUBLESHOOTING
If any error lights are illuminated or flashing on your Shark® AI Robot VACMOPTM, see the error code chart below:

ERROR CODE
CLEAN (RED) + ! (RED) flashing CLEAN (RED) flashing DOCK (RED) flashing CLEAN (WHITE) + DOCK (RED) solid CLEAN (RED) + DOCK (WHITE) flashing CLEAN (RED) + DOCK (RED) flashing DOCK (RED) + ! (RED) flashing CLEAN (RED) + DOCK (RED) + ! (RED) flashing CLEAN (WHITE) + DOCK (RED) + ! (RED) flashing CLEAN (WHITE) + ! (RED) flashing CLEAN (RED) + DOCK (WHITE) + ! (RED) flashing CLEAN (WHITE) + DOCK (RED) flashing BATTERY ICON (RED) flashing CLEAN (RED) + DOCK (WHITE) flashing + ! (RED) DROPLET ICON (RED) solid

SOLUTION
Suction motor failure. Remove and empty the dust bin, clean the filters, and remove blockages to ensure nothing is reducing suction.
Robot may be stuck on an obstacle. Move robot to a new location on a level surface.
Front bumper may be jammed. Clean the bumper and make sure it moves in and out freely.
BotBoundary® error. Move your robot to a flat surface away from the magnetic boundary strip and try cleaning again.
Cliff sensor error. Move your robot to a new location and clean its cliff sensors.
Robot dust bin has been removed and needs to be reinserted.
Side brush is stuck. Remove any debris from around the side brushes.
A drive wheel is stuck. Clean the wheels and remove any debris wrapped around the axles.
Wheel motor encoder failure. Please contact Shark Customer Service at 1-855-460-5425.
Blockage in brushroll. Remove any debris from around the brushroll.
Robot has encountered an error while booting. Please turn the power off and back on.
Robot cannot locate dock. Please pick up your robot and place it on the dock.
Battery is critically low and needs recharging. If your robot is unable to dock, place the robot manually on the dock.
Robot is stuck. Please move to a level surface.
Fluid Reservoir is empty. Refill before cleaning.

For all other issues, please call Customer Service at 1-855-460-5425.

sharkclean.com

END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE
IMPORTANT: PLEASE READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT CAREFULLY BEFORE CONTINUING WITH THIS PROGRAM INSTALL OR USE OF THIS PRODUCT: SharkNinja Operating LLC’s (“SharkNinja”) End-User License Agreement (“EULA”) is a legal agreement between You (either a single entity or an individual) and SharkNinja for SharkNinja’s Software Applications, including those installed by You onto your SharkNinja products or already installed on your device, including all firmware (referred hereafter as “SN APPS”). By installing, copying, checking a box, clicking a button confirming your agreement to these terms, or otherwise continuing to use the SN APPS, You agree to be bound by the terms of this EULA. This license agreement represents the entire agreement concerning SN APPS between You and SharkNinja, and it supersedes any prior proposal, representation, or understanding between the parties. If You do not agree to the terms of this EULA, do not install or use the SN APPS or this product. The SN APPS are protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties.
1. GRANT OF LICENSE. The SN APPS are licensed as follows: 1.1 Installation and Use. SharkNinja grants You the right to download, install, and use SN APPS on the specified platform for which the SN APP was designed and in connection with SharkNinja products with which the SN APPS are designed to operate (“SN Devices”). 1.2 Backup Copies. You may also make a copy of SN APPS downloaded and installed by You for backup and archival purposes. 2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS. 2.1 Maintenance of Copyright Notices. You must not remove or alter any copyright notices on any and all copies of the SN APPS. 2.2 Distribution. You may not distribute copies of the SN APPS to third parties. 2.3 Prohibition on Reverse Engineering, Decompilation, and Disassembly. You may not reverse engineer, decompile, or disassemble SN APPS, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. 2.4 Rental. You may not rent, lease, or lend SN APPS without written permission from SharkNinja. 2.5 NOT FOR RESALE SOFTWARE. Applications identified as “Not for Resale” or “NFR,” may not be resold, transferred, or used for any purpose other than demonstration, test, or evaluation. 2.6 Support Services. SharkNinja may provide You with support services related to SN APPS (“Support Services”). Any supplemental software code provided to You as part of the Support Services shall be considered part of SN APPS and subject to the terms and conditions of this EULA. 2.7 Compliance with Applicable Laws. You must comply with all applicable laws regarding use of SN APPS. 3. UPDATES. SharkNinja may provide You with upgrades or updates to SN APPS. This EULA will govern any upgrades provided by SharkNinja that replace and/or supplement SN APPS, unless such upgrade is accompanied by a separate EULA, in which case the terms of that EULA will govern. If You decide not to download and use an upgrade or update provided by SharkNinja, You understand that You could put SN Apps at risk to serious security threats or cause SN Apps to become unusable or unstable. 4. DATA AND PRIVACY. SharkNinja is committed to ensuring your privacy by adhering to high standards of fairness and integrity. We are committed to keeping our customers informed about how we use the information we gather from You through the use of each of our websites or SN APPS. Our privacy practices are described in SharkNinja’s Privacy Policy, as well as in separate notices given when an app, product, or service is purchased or downloaded. By using SN APPs or providing us with your personal information, You are accepting and consenting to the practices, terms, and conditions described in SharkNinja’s Privacy Policy. At all times your information will be treated in accordance with the SharkNinja Privacy Policy, which is incorporated by reference into this EULA and can be viewed at the following URL: http://www.sharkninja.com/privacypolicy. 5. THIRD-PARTY APPLICATION LIBRARIES AND EMBEDDED SOFTWARE. 5.1 You acknowledge that Ayla Networks, Inc. (“Ayla”) has provided certain application libraries that have been embedded into SN APPS (“Ayla Application Libraries”) and enables SN Devices to connect to the Ayla Cloud Service (“Ayla Embedded Software”). 5.2 You will not use the Ayla Application Libraries except as an incorporated portion of SN APPS, unmodified from the form provided to You. 5.3 You will not use the Ayla Embedded Software except as an incorporated portion of SN Devices, unmodified from the form provided to You. 5.4 You will not modify, adapt, translate, or create derivative works based on, or decompile, disassemble, reverse engineer, or otherwise attempt to derive the source code or underlying algorithms of, the Ayla Application Libraries or the Ayla Embedded Software. 5.5 SharkNinja retains all ownership of SN APPS (and the Ayla Application Libraries contained therein) and any software installed on SN Devices (including the Ayla Embedded Software) and only a license thereto is granted to You for use in connection with the SN APPS and SN Devices.
sharkclean.com

END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE
5.6 You will not use the Ayla Application Libraries or Ayla Embedded Software to attempt to gain unauthorized access to or use of the systems/services of SharkNinja’s other licensors; nor will You transmit viruses, worms, Trojan horses, time bombs, spyware, malware, cancelbots, passive collection mechanisms, robots, data mining software, or any other malicious or invasive code or program into the systems/services of SharkNinja’s other licensors.
5.7 You will not use the Ayla Application Libraries or Ayla Embedded Software to interfere with, breach, or circumvent any security feature, authentication feature, or any other feature that restricts or enforces limitations on the use of, or access to, the systems/services of SharkNinja’s other licensors.
5.8 You will not probe, attack, scan, or test the vulnerability of the systems/services of SharkNinja’s other licensors.
5.9 SharkNinja’s other licensors of the SN APPS, Ayla Application Libraries, and the Ayla Embedded Software are the express third-party beneficiaries of this EULA, and the provisions of this Section of this EULA are made expressly for the benefit of such licensors, and are enforceable by such licensors.
6. TERMINATION. Without prejudice to any other rights, SharkNinja may terminate this EULA if You fail to comply with the terms and conditions of this EULA. In such event, You must destroy all copies of SN APPS in your possession.
7. COPYRIGHT. All title, including but not limited to copyrights, in and to SN APPS and any copies thereof are owned by SharkNinja or its suppliers. All title and intellectual property rights in and to the content which may be accessed through use of SN APPS are the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not expressly granted are reserved by SharkNinja.
8. OPEN SOURCE SOFTWARE. You hereby acknowledge that SN APPS may contain software that is subject to “open source” or “free software” licenses (“Open Source Software”). The license granted by this EULA does not apply to Open Source Software contained in the SN APPS. Rather, the terms and conditions in the applicable Open Source Software license shall apply to the Open Source Software. Nothing in this EULA limits your rights under, or grants You rights that supersede, any Open Source Software license. You acknowledge that the Open Source Software license is solely between You and the applicable licensor of the Open Source Software. To the extent the terms of the licenses applicable to the Open Source Software require SharkNinja to provide the Open Source Software, in either source or executable form, or to provide copies of applicable license terms or other required information, You may obtain a copy of the software by contacting SharkNinja at the below physical address. Additional information about the Open Source Software, and its terms of use, may be found at www.sharkclean.com/opensource.
9. NO WARRANTIES. SharkNinja expressly disclaims any warranty for SN APPS, Ayla Application Libraries, or Ayla Embedded Software. SN APPS, Ayla Application Libraries, and Ayla Embedded Software are provided `As Is’ without any express or implied warranty of any kind, including but not limited to any warranties of merchantability, noninfringement, fitness of a particular purpose, or title. SharkNinja does not warrant or assume responsibility for the accuracy or completeness of any information, text, graphics, links, or other items contained within the SN APPS. SharkNinja makes no warranties respecting any harm that may be caused by the transmission of a computer virus, worm, logic bomb, or other such computer program. SharkNinja further expressly disclaims any warranty or representation to any third party.
10. LIMITATION OF LIABILITY. In no event shall SharkNinja or its suppliers be liable for any special, incidental, punitive, indirect, or consequential damages whatsoever (including, but not limited to, damages for loss of profits or confidential or other information, for business interruption, for personal injury, for loss of privacy, for failure to meet any duty including of good faith or of reasonable care, for negligence, and for any other pecuniary or other loss whatsoever) arising out of or in any way related to the use of or inability to use SN Devices or SN APPS, the provision of or failure to provide support or other services, information, software, and related content through the product or otherwise arising out of the use of SN APPS, or otherwise under or in connection with any provision of this EULA, even in the event of the fault, tort (including negligence), strict liability, breach of contract, or breach of warranty of SharkNinja or any supplier, and even if SharkNinja or any supplier has been advised of the possibility of such damages. SharkNinja shall have no liability with respect to the content of the SN APPS or any part thereof, including but not limited to errors or omissions contained therein, libel, infringements of rights of publicity, privacy, trademark rights, business interruption, personal injury, loss of privacy, moral rights, or the disclosure of confidential information.
11. APPLICABLE LAW. The laws of the Commonwealth of Massachusetts will govern this EULA and You hereby consent to exclusive jurisdiction and venue in the state and federal courts sitting in the Commonwealth of Massachusetts.
12. ASSIGNMENT. SharkNinja may assign this EULA without notice to Licensor.
13. ENTIRE AGREEMENT. This EULA (including any addendum or amendment to this EULA which is included with the SN Devices) is the entire agreement between You and SharkNinja relating to the SN APPS and supersedes all prior or contemporaneous oral or written communications, proposals and representations with respect to the SN APPS or any other subject matter covered by this EULA. To the extent the terms of any SharkNinja policies or programs for support services conflict with the terms of this EULA, the terms of this EULA shall control.
If You have questions regarding this EULA, please contact SharkNinja at 89 A Street, Suite 100, Needham, MA 02494.
sharkclean.com

ONE (1) YEAR LIMITED WARRANTY
The One (1) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original product only and is not transferable. SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period of one (1) year from the date of purchase when it is used under normal household conditions and maintained according to the requirements outlined in the Owner’s Guide, subject to the following conditions and exclusions: What is covered by this warranty? 1. The original unit and/or non-wearable components deemed defective, in SharkNinja’s sole discretion,
will be repaired or replaced up to one (1) year from the original purchase date. 2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the
receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value. What is not covered by this warranty?

1. Normal wear and tear of wearable parts (such as foam filters, filters, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com. 2. Any unit that has been tampered with or used for commercial purposes. 3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure to perform required maintenance (e.g., not cleaning the filters), or damage due to mishandling in transit. 4. Consequential and incidental damages.
2. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja. 6. Products purchased, used, or operated outside North America. How to get service If your appliance fails to operate properly while in use under normal household conditions within the warranty period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service Specialists are also available at 1-855-460-5425 to assist with product support and warranty service options, including the possibility of upgrading to our VIP warranty service options for select product categories. Please register your product and have it with you when contacting Customer Service. SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of $24.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit. How to initiate a warranty claim You must call 1-855-460-5425 to initiate a warranty claim. You will need the receipt as proof of purchase. A Customer Service Specialist will provide you with return and packing instruction information. How state law applies This warranty gives you specific legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
   sharkclean.com

REGISTER YOUR PURCHASE
registeryourshark.com
RECORD THIS INFORMATION Model Number: Date Code: Date of Purchase: (Keep receipt) Store of Purchase:
TIP: You can find the model and serial numbers on the QR code labels on the bottom of the robot and battery.
EXPECTED PERFORMANCE Expected runtime: 60 minutes Expected charging time: 6 hours
FCC WARNINGS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to parts 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. This Device complies with part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The user should avoid prolonged exposure within 20cm of the antenna, which may exceed the FCC radio frequency exposure limits. Note: If the consumer would like to comply with the to the energy efficiency guide lines it is recommended that after every use the end user place the robot into low power mode by switching the power switch to the off position (0). Even though the robot is in the off position the charging circuit will stay active and charge the unit. ISED STATEMENT This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference (2) This device must accept any interference, including interference that may cause undesired operation of the device.
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE. This Owner’s Guide is designed to help you keep your Shark® AI Robot VACMOPTM running at peak performance. SharkNinja Operating LLC US: Needham, MA 02494 CAN: Ville St- Laurent, QC H4S 1A7 1-855-460-5425 sharkclean.com Illustrations may differ from actual product. We are constantly striving to improve our products; therefore the specifications contained herein are subject to change without notice. For SharkNinja U.S. Patent information, visit sharkninja.com/uspatents
sharkclean.com

CONSIGNES DE SÉCURITÉ IMPORTANTES
VEUILLEZ LES LIRE ATTENTIVEMENT AVANT L’UTILISATION · POUR UN USAGE DOMESTIQUE SEULEMENT
Si le cordon d’alimentation du chargeur ne s’insère pas à fond dans la prise de courant, inversez alors le sens de la fiche. Si elle ne s’insère toujours pas, communiquez avec un électricien qualifié. NE FORCEZ PAS pour insérer la fiche dans la prise et ne tentez pas de la modifier.

AVERTISSEMENT
Afin de réduire les risques d’incendie, de décharges électriques, de blessure ou de dommage matériel :

AVERTISSEMENTS GÉNÉRAUX Lors de l’utilisation d’un appareil électrique, des précautions de base doivent toujours être suivies, y compris les suivantes :

1. Cet appareil se compose d’un aspirateur robot
   humide/sec pour les planchers et d’une station de recharge avec alimentation électrique. Ces composantes comportent des raccordements électriques, du filage électrique et des pièces amovibles pouvant exposer l’utilisateur à certains risques. 2. Avant chaque utilisation, inspectez soigneusement toutes les pièces afin de déceler tout dommage. Si une pièce est endommagée, cessez son utilisation. 3. Utilisez uniquement des pièces de rechange identiques. Voir la page des accessoires de remplacement de ce livret. 4. Ce robot nettoyant humide/sec pour les planchers ne renferme aucune pièce qui peut être réparée. 5. Utilisez cet appareil uniquement aux fins décrites dans ce manuel. N’UTILISEZ PAS le robot nettoyant humide/ sec pour les planchers pour un usage autre que ceux décrits dans le présent manuel. 6. À l’exception des filtres, des récipients à poussière et des tampons, N’EXPOSEZ aucune des pièces du robot nettoyant humide/sec pour les planchers à l’eau ou à d’autres liquides. AVERTISSEMENTS CONCERNANT L’UTILISATION 7. Cet appareil peut être utilisé par des personnes dont les capacités physiques, sensorielles ou mentales sont réduites ou qui manquent d’expérience et de connaissances si ces personnes sont supervisées ou informées sur l’utilisation sécuritaire de l’appareil et s’ils comprennent les dangers possibles.
   a) Les enfants ne doivent pas jouer avec l’appareil.
   b) Les enfants ne peuvent pas nettoyer ni entretenir l’appareil sans supervision.
   8. Éteignez toujours l’aspirateur robot avant d’insérer ou de retirer le filtre, le récipient à poussière ou le réservoir de liquide.
   9. NE MANIPULEZ PAS la prise, la station de recharge, le cordon d’alimentation ou le robot nettoyant humide/sec pour les planchers avec les mains mouillées. Les enfants ne peuvent pas nettoyer ni entretenir l’appareil sans supervision.
   10. N’UTILISEZ PAS le robot sans que le récipient à poussière, le filtre ou le réservoir de liquide ne soient bien en place.

11. N’ENDOMMAGEZ PAS le cordon d’alimentation : a) N’UTILISEZ PAS le cordon comme une poignée pour porter ou tirer la station de recharge. b) NE DÉBRANCHEZ PAS l’appareil en tirant le cordon d’alimentation. Agrippez la fiche, non le cordon. c) NE FERMEZ PAS une porte sur le cordon, ne tirez pas le cordon sur des coins pointus et ne laissez pas le cordon près de surfaces chaudes.
12. ÉVITEZ d’insérer des objets dans les ouvertures de la buse ou de tout autre accessoire. N’UTILISEZ PAS l’appareil si une ouverture est obstruée. Veillez à ce que les ouvertures ne soient pas bloquées par de la poussière, de la peluche, des cheveux ou tout autre élément qui pourrait gêner la circulation de l’air.
13. N’UTILISEZ PAS le robot nettoyant humide/sec pour les planchers si son débit d’air est obstrué. Si les conduits d’air se bloquent, éteignez l’aspirateur et retirez toutes les obstructions avant d’allumer l’appareil de nouveau.
14. Tenez tous les orifices d’aspiration éloignés des cheveux, du visage, des doigts, des pieds déchaussés ou de vêtements amples.
15. N’UTILISEZ PAS le robot nettoyant humide/ sec pour les planchers s’il ne fonctionne pas comme prévu, ou s’il a été échappé sur le sol, endommagé, laissé à l’extérieur ou immergé.
16. NE PLACEZ PAS l’aspirateur sur des surfaces instables,
17. Si le robot est placé dans une pièce et qu’il ne part pas de la station de recharge, il doit être placé dans un périmètre non obstrué de 45 cm de distance des bords et des chutes.
18. N’UTILISEZ PAS l’appareil pour aspirer : a) Des liquides déversés b) De gros objets c) Des objets durs ou tranchants (verre, clous, vis ou pièces de monnaie) d) De grandes quantités de poussière (poussière de cloison sèche, cendres ou braises de foyer). N’UTILISEZ PAS l’aspirateur comme accessoire d’un outil électrique pour l’aspiration de la poussière. e) Des objets produisant de la fumée ou à combustion (braises chaudes, embouts de cigarettes ou allumettes) f) Des matières inflammables ou combustibles (essence à briquet, essence ou kérosène)

sharkclean.com

g) Des matières toxiques (forte concentration de liquide de Javel, forte concentration d’ammoniaque ou du produit débouchant)
19. N’UTILISEZ PAS dans les zones suivantes : a) Zones extérieures à proximité de foyers dont la porte n’est pas obstruée b) Dans des endroits fermés pouvant contenir des matières explosives, ou des fumées ou vapeurs toxiques (essence à briquet, essence, kérosène, peinture, diluants à peinture, produits de traitement antimite ou poussières inflammables) c) Dans une zone avec chauffage d’appoint d) Près de foyers dont la porte n’est pas obstruée
20. Éteignez le robot nettoyant humide/sec pour les planchers avant de procéder à tout ajustement, nettoyage, entretien ou dépannage. Remarque : en position OFF (arrêt) (O), le robot continue de consommer une petite quantité d’énergie.
21. Laissez tous les filtres sécher complètement avant de les remettre dans le robot nettoyant humide/sec pour les planchers pour éviter que du liquide ne soit aspiré dans les composants électriques.
22. NE MODIFIEZ PAS ni ne tentez de réparer le robot nettoyant humide/sec pour les planchers ou la batterie vous-même, à moins d’indication contraire dans ce manuel. N’UTILISEZ PAS l’aspirateur s’il a été modifié ou endommagé.
23. Retirez tout liquide renversé ou ayant fui du tapis, de la base ou du plancher de la station, car cela pourrait entraîner un risque de choc électrique.
24. Faites un essai sur une petite surface discrète du sol, avec une petite quantité de la solution de nettoyage VACMOPTM pour vous assurer que cela n’abîme pas le sol.
25. Lorsque vous remplissez le réservoir, vérifiez s’il y a des fuites, car les liquides accumulés constituent un risque de glissement et peuvent provoquer des chocs électriques. Si le réservoir est endommagé, il doit être remplacé.
26. Faites attention en marchant sur les sols nettoyés, car ils peuvent être glissants lorsqu’ils sont humides.
27. Pour que les capteurs de chute de votre robot fonctionnent adéquatement, tous les tapis ou les carpettes doivent être placés à un minimum de 20 cm des escaliers (ou se prolonger de façon continue par-dessus la limite des marches). Si l’extrémité d’un tapis ou d’une carpette à moins de 20 cm des marches ne peut être déplacée, utilisez une lanière BotBoundary® pour bloquer l’accès aux escaliers. Les lanières BotBoundary ne sont pas incluses avec votre robot.

UTILISATION DE LA BATTERIE 28. La batterie est la source d’alimentation de
l’aspirateur. Lisez attentivement et respectez les instructions de chargement. 29. Afin d’éviter qu’il ne se mette en marche par erreur, assurez-vous que l’aspirateur est éteint avant de le soulever ou de le transporter. NE TRANSPORTEZ PAS l’appareil avec votre doigt sur l’interrupteur d’alimentation. 30. Utilisez UNIQUEMENT la station de recharge Shark® XDCKRV2000 et la batterie RVBAT850A. L’utilisation d’autres chargeurs ou d’autres batteries que celles-ci pourrait causer un risque d’incendie. 31. Gardez la batterie à l’écart des objets métalliques comme des trombones, de la monnaie, des clés, des clous ou des vis. Courtcircuiter les bornes de la batterie augmente le risque d’incendie ou de brûlures. 32. Si la batterie est utilisée de façon inappropriée, il se peut que du liquide s’en échappe. Évitez le contact avec ce liquide, car il pourrait causer des irritations ou des brûlures. En cas de contact, rincez à l’eau. Si le liquide entre en contact avec les yeux, obtenez de l’aide médicale. 33. L’aspirateur robot ne doit pas être entreposé, chargé ou utilisé à des températures inférieures à 10 °C ou supérieures à 40 °C. Assurez-vous que la batterie et l’aspirateur sont à température pièce avant de les recharger ou de les utiliser. L’exposition du robot ou de la batterie à des températures hors de la plage indiquée peut endommager l’appareil et augmenter le risque d’incendie. 34. N’EXPOSEZ PAS le robot nettoyant humide/ sec pour les planchers ou la batterie au feu ou à une température supérieure à 130 °C, car cela peut provoquer une explosion. 35. Les batteries non rechargeables ne peuvent pas être rechargées.
LANIÈRES BOTBOUNDARY® 31. NE PLACEZ PAS les lanières BotBoundary
sous les tapis ou les carpettes. 32. NE PLACEZ PAS les lanières BotBoundary
l’une sur l’autre. 33. Utilisez toujours des lanières BotBoundary
autour des planchers et surfaces réfléchissants. 34. Les lanières BotBoundary doivent toujours être utilisées près des marches recouvertes de tapis. 35. NE PLACEZ PAS les lanières BotBoundary à moins de trois mètres de la station de recharge. 36. Pour que les capteurs de chute de votre robot fonctionnent adéquatement, tous les tapis ou les carpettes doivent être placés à un minimum de 20 cm des escaliers (ou se prolonger de façon continue par-dessus la limite des marches). Si l’extrémité d’un tapis ou d’une carpette qui est à moins de 20 cm des marches ne peut être déplacée, vous devez utiliser une lanière BotBoundary pour bloquer l’accès aux escaliers.

CONSERVEZ CES INSTRUCTIONS

Pour les mises en garde et les avertissements les plus récents, allez à sharkclean.com/robothelp

sharkclean.com

PRÉSENTATION DU SHARK® AI ROBOT VACMOPTM

Voyant indicateur d’erreur

Voyants indicateurs de recharge

Voyant indicateur Wi-Fi

Parechoc avant Bouton Clean (nettoyer)

Bouton Dock (station de recharge)
Voyant indicateur de vadrouille

Réservoir de liquide

Bouton Power (mise en marche)

PRÉSENTATION DU SHARK® AI ROBOT VACMOPTM
RÉSERVOIR DE LIQUIDE Boutons de retrait

Port de remplissage

Fente de tampon

PARTIE AVANT DE LA STATION DE RECHARGE

PARTIE INFÉRIEURE DE LA STATION DE RECHARGE

Station de recharge

Capteurs de chute et de frontières

Brosse latérale Compartiment de la batterie Brosse rotative autonettoyante
sharkclean.com

Tampon de chargement
Roulette pivotante avant
Roue motrice Porte d’accès de la
brosse rotative
Récipient à poussière et filtre

Tampons de chargement

Crochet d’enroulement du cordon du chargeur

TAPIS DE LA STATION DE RECHARGE (Ce côté vers le haut)

sharkclean.com

CONFIGURATION DE LA STATION DE RECHARGE

EN CHARGE
IMPORTANT : Le Shark® AI Robot est doté d’une batterie rechargeable préinstallée. Chargez complètement la batterie avant la première utilisation. Il pourrait falloir jusqu’à 6 heures pour une charge complète.

3 ft. 3 ft.
5 ft.

· Pour la station de recharge, choisissez un emplacement permanent doté d’un signal Wi-Fi puissant, car toutes les fois que vous la déplacez, votre robot devra de nouveau cartographier complètement votre maison.
· Placez la station de recharge le dos contre un mur et attachez le tapis. Choisissez une surface plane sur le plancher, dans une zone centrale. Ne placez pas contre une plinthe ou près d’un élément chauffant.
· Déplacez tous les objets situés à moins de 1 m de chaque côté de la station de recharge, ou à moins de 1,5 m de l’avant de la station de recharge.
· Branchez la station de recharge. Le voyant indicateur devient vert lorsque la station de recharge est branchée.
INSTALLATION DES BROSSES LATÉRALES
Insérez les deux brosses latérales comprises dans les chevilles carrées logées sur le dessous du robot.

Pour charger le robot, placez-le sur la station de recharge. Mettez le bouton Power (mise en marche), situé sur le côté du robot, à la position ON (marche) (I). Le robot émet un signal sonore lorsque la charge commence et le témoin de charge sur la station passe du vert au bleu.

Lorsque le cycle de nettoyage se termine, ou si la batterie est faible, le robot recherchera la station de recharge. Si le robot ne retourne pas à la station de recharge, sa charge peut être épuisée, ou s’il est en mode de nettoyage humide, la station de recharge peut être bloquée par un tapis.

sharkclean.com

Si le robot n’a plus de charge et ne peut pas retourner à la station de recharge, placez-le vousmême. Le voyant indicateur devient bleu et le robot émet un signal sonore lorsqu’il est correctement placé sur la station de recharge.
REMARQUE : Lors du placement manuel du robot sur la station de recharge, assurez-vous que les contacts de charge, situés sur le dessous du robot, sont alignés sur les contacts de la station de recharge. Pendant que le robot charge, les deux voyants DEL blancs s’allument en alternance. Une fois l’appareil complètement chargé, les deux voyants blancs s’allumeront en continu. REMARQUE : Au moment de ramasser le robot, évitez de placer vos doigts entre le parechoc et la base du robot.
sharkclean.com

VOYANTS INDICATEURS DE RECHARGE

En cours d’utilisation

Complètement chargé (Blanc)

Charge partielle (Blanc)

Durant la charge (Blanc)

Charge faible (Rouge)

Charge nulle ou éteint
Les voyants indicateurs de recharge blancs indiquent la charge de batterie restante.
Pendant que le robot charge, les deux voyants DEL blancs s’allument en alternance. Une fois l’appareil complètement chargé, les deux voyants blancs s’allumeront en continu. Il pourrait falloir jusqu’à six heures pour charger entièrement votre robot.
Si le robot est en mode inactif et à l’écart de la station de recharge pendant 10 minutes, il entrera en Mode veille. Les voyants indicateurs s’éteignent, mais la batterie et les voyants Wi-Fi restent allumés en mode veille. Réveillez le robot en appuyant sur n’importe quel bouton.
REMARQUE : Si le voyant de recharge faible clignote en rouge, il n’y a pas assez de charge de batterie pour que le robot puisse revenir à la station. Placez manuellement le robot sur la station de recharge.
CONSEIL : Pour préserver la durée de vie de la batterie lorsque le robot n’est pas utilisé pendant une période prolongée, mettez l’interrupteur d’alimentation en position d’arrêt. Le robot doit être rechargé au moins une fois par trimestre. L’interrupteur doit être en position ON (marche) pour charger le robot.

IMPORTANT : Avant de nettoyer une pièce entière pour la première fois, nous vous recommandons de tester d’abord votre appareil sur une petite partie du plancher afin de vous assurer qu’il ne cause pas de rayures.
sharkclean.com

BOUTONS ET VOYANTS INDICATEURS
BOUTON CLEAN (NETTOYER) Appuyez sur le bouton pour commencer un cycle de nettoyage. Appuyez à nouveau sur le bouton pour l’arrêter.
BOUTON DOCK (STATION DE RECHARGE) Appuyez pour arrêter le nettoyage et renvoyer l’appareil sur la station de recharge.
LES VOYANTS INDICATEURS DE RECHARGE indiquent la quantité de charge restante dans la batterie.

RECHARGE & RESUME (RECHARGER ET CONTINUER) Appuyez sur le bouton CLEAN (nettoyer) et maintenez-le enfoncé pendant 15 secondes pour activer ou désactiver la fonction Recharge & Resume (recharger et continuer).
La fonction Recharge & Resume (recharger et continuer) est désactivée par défaut. Activez la fonction Recharge & Resume (recharger et continuer) pour une couverture complète si le plan d’étage de votre maison est supérieur à 140 m². Votre robot retournera à la station de recharge, se rechargera, puis pourra reprendre le nettoyage là où il s’est arrêté.

LE VOYANT INDICATEUR DE VADROUILLE MOUILLÉE s’allume lorsque le réservoir de liquide est correctement installé. L’icône de goutte devient rouge s’il n’y a pas de liquide dans le réservoir. Après 15 minutes, le robot retournera à la station de recharge si le réservoir n’est pas rempli. VOYANT INDICATEUR D’ERREUR « ! » Consultez la section Dépannage pour voir la liste complète des codes d’erreurs.
VOYANT INDICATEUR WI-FI Voyant blanc : connecté au Wi-Fi. Voyant rouge : non connecté. Voyant blanc clignotant : mode de configuration. Aucun voyant : pas encore configuré.
sharkclean.com

References

• Find Shark® Clean Parts & Accessories - Shark®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>