Honeywell HPA030 Series HPA030B Hepa Air Purifier Owner’s Manual

HEPA Air Purifier
Owner’s Manual
HPA030 SERIES

If you have any questions about the operation of this product, please call us toll-free at 1-800-477-0457, or visit our website at: www.HoneywellPluggedIn.com/contact- us

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS AIR PURIFIER

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before operating the air purifier.
2. Place air purifier where it would not be easily overturned by persons in the household.
3. ALWAYS turn the air purifier controls to the off position and unplug from the wall outlet when not in use.
4. To disconnect the air purifier, make sure the unit is powered OFF then grip the plug and pull it from the wall outlet. NEVER pull by the cord.
5. DO NOT use any product with a damaged cord or plug, any product that malfunctions, or any product that has been dropped or damaged in any manner. Keep the cord away from heated surfaces.
6. DO NOT use an air purifier outdoors.
7. DO NOT use an air purifier unless it is fully assembled.
8. DO NOT run power cord under carpets, and DO NOT cover with throw rugs. Arrange the cord such that it will not be a tripping hazard.
9. DO NOT use an air purifier where combustible gases or vapors are present.
10. DO NOT expose the air purifier to rain, or use near water, in a bathroom, laundry area, or other damp location.
11. The air purifier MUST be used in its upright position.
12. DO NOT allow foreign objects to enter ventilation or exhaust opening as this may cause electric shock or damage to the air purifier. DO NOT block air outlets or intakes.
13. Locate air purifier near the outlet and DO NOT use with an extension cord or power strip.
14. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. do not attempt to defeat this safety feature.
15. A loose fit between the AC outlet (receptacle) and plug may cause overheating and a distortion of the plug. Contact a qualified electrician to replace the loose or worn outlets.
16. DO NOT sit, stand, or place heavy objects on the air purifier.
17. ALWAYS disconnect the power supply before servicing.
18. Keep out of reach of children and pets.
19. Filters may be harmful if ingested. Avoid breathing dust when changing filters.
20. SAVE THESE INSTRUCTIONS.

For FCC compliance information, please see the last page of this manual.

WARNING: To Reduce The Risk of Fire or Electric Shock, DO NOT Use This Air Purifier With Any Solid-State Speed Control Device.

GETTING TO KNOW YOUR AIR PURIFIER

HOW YOUR AIR PURIFIER WORKS

This model air purifier incorporates a 2-stage cleaning system to help clean the air that passes through the filter in the unit (Fig. 1).
Stage 1: Type Odor Reducing Pre-Filter Pre-Filter
Stage 2: Type Certified HEPA Filter captures the Filter following microscopic airborne allergens and particles: dust, pollen, pet dander, dust mite debris, and smoke, as small as 0.3 microns from the air that passes through the filter.

GETTING STARTED

• Select a firm, level, and flat location.
• When operating, large volumes of air are drawn toward the air purifier. Surrounding areas should be cleaned and/or vacuumed frequently to prevent the build-up of dust and other contaminants. This may also help prolong the life of the filter. If the unit is placed on a light-colored carpet, a small mat or rug should be used underneath to prevent staining. This is especially important in homes with contamination from smoking, fireplaces, or where candles are burned.
• Ensure the front of the unit faces away from the closest wall or furniture.
• Ensure no grilles are blocked.

INSTALLING CERTIFIED HEPA FILTERS AND ODOR-REDUCING PRE-FILTER

The Certified HEPA Filters and Odor Reducing Pre-Filter are supplied with your air purifier. They are wrapped to ensure purity and are labeled to help identify the proper replacement filter. (Type Certified HEPA Filter; Filter
Type Odor Reducing Pre-Filter) Pre-Filter

• Turn off and unplug the air purifier. While pressing the notch at the top of the rear grille, pull the grille towards you and remove it (See Fig. 2). Gently push along the edge of the filter frame and pull forward. If replacing used filters, you may pull the red tabs to remove the filter. Repeat for the second filter.
• Remove protective wrap from the filters, including the pre-filter.
• Place the Certified HEPA Filters back into the air purifier housing with the Fig. 2 red tabs accessible for removal.
• Secure the Odor Reducing Pre-Filter under the tabs on the rear grille.
• Re-install the rear grille by inserting the lower tab into the tab slot at the bottom of the air purifier. Push the top of the grille into place until you hear an audible “click.”

OPERATION

The energy efficiency of this ENERGY STAR certified model is measured based on a ratio between the model’s CADR for Smoke and the electrical energy it consumes, or CADR/Watt.

• Ensure the air purifier is plugged into a working electrical outlet.
• Press the power button ( ) once. The unit will start at high speed (Fig. 3).
• Press the power button again to select a different cleaning level. An LED will illuminate to indicate which cleaning level you have selected. (III = High, II = Medium, I = Low)

Portable air purifiers are more effective in rooms where all doors and windows are closed. It is recommended that you run your air purifier while you are at home to help clean the air.

ELECTRONIC FILTER CHECK REMINDER

This model air purifier has an electronic filter check to remind you when to check and replace the Certified HEPA Filters and Pre-Filter based on the air purifier’s hours of use. A red LED will illuminate when it is time to check/replace the filters.
Will illuminate when it is time to replace the Certified HEPA Filters or Odor Reducing Pre-Filter
When the Certified HEPA Filters or Pre-Filter need to be replaced, the light will remain on until it is RESET. You may unplug the air purifier without interrupting the filter check.
You should periodically check the filters. Depending on operating conditions, the Certified HEPA Filters should be replaced every 12 months and pre-filter every 3 months.

REPLACE WITH CERTIFIED HEPA FILTER G and ODOR Filter REDUCING PRE-FILTER A Pre-Filter

These cleaning intervals are intended as guidelines only.
The performance of any filter media is dependent upon the concentration of particles going through the system. High concentrations of particles such as dust, pet dander, and smoke will reduce the useful performance of the filter.

NOTE: None of the filters are washable. DO NOT immerse them in water.
WARNING: Filters may be harmful if ingested. Avoid breathing dust when changing filters.
To RESET the Electronic Filter Check:
When the Check Filter LED remains on and solid, it is time to replace the Odor Reducing Pre-Filter and reset the filter monitor. With the unit powered ON, press the FILTER RESET button below the Check Filter LED and hold for approximately 2 seconds until the light turns off (Fig. 4).

When the LED illuminates and is flashing, it is time to replace the Certified HEPA Filters and reset the filter monitor. With the unit powered ON, press the FILTER RESET button and hold for approximately 2 seconds until the light turns OFF (Fig. 4).

Manual (or Early) Reset of Electronic Filter Check
Depending on your individual usage (environment and hours used), you may need to replace the filters more or less frequently. Each time you replace your filters, you should reset the filter monitor. You may manually reset the filter monitor for the pre-filter or the HEPA filter or both. If you change the pre-filter or Certified HEPA Filter before the Check Filter LED is illuminated, it is possible to reset the filter monitor. You must first manually illuminate the Check Filter LED. Follow these steps:

1. With the unit powered ON, press the FILTER RESET button for 5 seconds to illuminate the LED in “solid” mode.
2. To reset filter monitor for Pre-Filter: press and hold the FILTER RESET button for 2 seconds until LED changes to flashing mode.
3. TAP FILTER RESET button to shut LED off. The Pre-Filter monitor is now set to “clean status”.
4. To reset filter monitor for HEPA Filter: LED must be in “flashing mode”. Follow Step 1 above, then the TAP FILTER RESET button again to illuminate the LED in “flashing mode”.
5. Press and hold the FILTER RESET button for 2 seconds until LED shuts off. The HEPA Filter monitor is now set to “clean status”.
6. To reset filter monitor for both Pre-Filter and HEPA Filter: Follow Steps 1, 2, and 5 above.

REPLACING THE CERTIFIED HEPA FILTERS

For optimum performance, it is recommended you replace the Type Filter Certified HEPA Filters every 12 months.
Use only Certified Honeywell Replacement Filters.
Remove and dispose of used filters. Avoid breathing dust when changing filters.
Please note this purifier takes 2 Filter Certified HEPA Filters.
See INSTALLATION INSTRUCTIONS on page 4 of this manual.
See the ACCESSORIES AND REPLACEMENT FILTERS section on page 6 of this manual to find out where to get filters.
There are stickers inside your air purifier near the filter cavity that note the Filter Type needed for your model.
WARNING: Filters may be harmful if ingested. Avoid breathing dust when changing filters.

REPLACING THE ODOR-REDUCING PRE-FILTER

The Odor Reducing Pre-Filter not only helps reduce odors but also helps capture large airborne particles that enter the grille. This pre-filter should be replaced every 3 months, as it will become covered with particles and fibers that will reduce filtration performance. Avoid breathing dust when changing filters.
Use the specially designed Type Pre-Filter Odor Reducing Pre-Filter. Use only Genuine Honeywell Replacement Filters.
See INSTALLATION INSTRUCTIONS on page 4 of this manual.
To purchase additional Pre-Filter Pre-Filters, see the Accessories and Replacement Filters section below.
WARNING: Filters may be harmful if ingested. Avoid breathing dust when changing filters.

CLEANING AND STORAGE

We recommend that you clean the air purifier at least once every 3 months and before extended storage. Use an only a dry cloth to wipe the external surfaces of the air purifier.
DO NOT USE WATER, WAX, POLISH, OR ANY CHEMICAL SOLUTION.
If your Air Purifier will not be used for more than 30 days, we recommend that you:

• Remove the Certified HEPA Filters and the Odor Reducing Pre-Filter from the unit.
• Place each filter in separate airtight plastic bags to preserve freshness.

ACCESSORIES AND REPLACEMENT FILTERS

You may purchase Honeywell replacement Certified HEPA Filter Filter and Honeywell Odor Reducing Pre-Filter Pre-Filter at the store where you purchased your air purifier or, order directly from www.HoneywellPluggedIn.com. To ensure stated product performance, use only Genuine Honeywell Replacement Filters. You have the option to use the Honeywell Household Gas & Odor Reducing Pre- Filter Pre-Filter instead of the Odor Reducing Pre-Filter Pre-Filter. It is also available at many retailers and on www.HoneywellPluggedIn.com.
If you have any questions, please call 1-800-477-0457 or go to www.HoneywellPluggedIn.com/contact-us.

FREQUENTLY ASKED QUESTIONS

My Air Purifier is starting to make noise and the air output is less. What’s wrong?
The filters may be dirty. High amounts of particles can block the pores in the filter and stop the air from moving through it. Replace the filters.
How long should I run my Air Purifier?
In general, the unit will be most effective when doors and windows are closed. It is recommended that you run your air purifier while you are at home to help clean the air. If desired or conditions warrant, you may run your air purifier 24 hours a day.
Can I wash any of the filters in my Air Purifier?
No. Washing any of the filters will ruin them.

CONSUMER RELATIONS

We are here to help. Call us toll-free at: 1-800-477-0457
Or visit our website at: www.HoneywellPluggedIn.com/contact- us
Please be sure to specify the model number.
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE YOUR WARRANTY. DO NOT RETURN TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE AIR PURIFIER OR PERSONAL INJURY.

5 YEAR LIMITED WARRANTY

You should first read all instructions before attempting to use this product.

A. This 5-year limited warranty applies to repair or replacement of products found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty. KAZ IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase.

B. At its option, Kaz will repair or replace this product if it is found to be defective in material or workmanship.
C. This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with the instruction manual.
D. This warranty does not cover the HEPA Filters or Pre-Filters except for material or workmanship defects. Please go to www.HoneywellPluggedIn.com/warrantyregistration to register your product and receive product information updates and new promotional offers.

© 2021 All rights reserved.
Kaz USA, Inc., a Helen of Troy Company
400 Donald Lynch Blvd., Suite 300, Marlborough, MA 01752
Honeywell is a trademark of Honeywell International Inc., used under license by Helen of Troy Limited.
Distributed in Canada by: Kaz Canada, Inc., a Helen of Troy Company
6700 Century Avenue, Suite 210, Mississauga, Ontario L5N 6A4
Contact us at 1-800-477-0457 or www.HoneywellPluggedIn.com/contact-us, in Canada www.HoneywellPluggedIn.ca
The ENERGY STAR name and marks are registered trademarks owned by the U.S. EPA.
Made in China

For Responsible recycling, please visit:
RECYCLE NATION
www.RecycleNation.com

A007018R0
080221

Creative Department
Artwork Specifications

Brand:
Category:
Model:
Artwork Part #:
Die Line Part #:
Subject: Region:
Flat Size:
Folded Size:
Scale:
Material:
Page Count:
Revision:
Date:
Release Date:
Re-release Date:| Honeywell
Air Purifiers
H PA030 Series
A007018R0 NA
Owner’s Manual
US
IN: Wllx H8
IN: W5.5 x H8
1/1
70# Matte Text
16
3
02AUG21
16AUG21
---|---

Colors:
Dielines (Do not print)
Spot Colors
Special Instructions :

Quality Requirement of Artwork and Quality
Clarification Process of Artwork Printing:
Meet Eng-QS-06&02
Helen of Troy
Creative Services
Marlborough, MA 01752, USA
+1 508 490 7000

References

• Honeywell Plugged In | Live More Comfortably
• Honeywell Plugged In | Live More comfortably
• Honeywell Plugged In | Live More comfortably
• Contact Us

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>