UNiKA PRO-248 Audio Interface Dual Active Direct Box User Manual

UNiKA PRO-248 Audio Interface Dual Active Direct Box

GENERAL PRECAUTION BEFORE USE

Thank you for purchasing the UNiKA PRO SERIES AUDIO INTERFACE. Before using, please read this manual carefully and pay attention to every detail that you must pay attention to. If you use a mixer to connect to this interface, please turn off the mixer power and +48V phantom power before connecting, and then turn on the power and phantom power after inserting the signal cables. For passive models, please do not turn on the phantom power to avoid leakage or damage the equipment.
If using a model with a volume knob, turn the volume knob to the minimum. During use, please do not plug or unplug the wires arbitrarily to avoid signal loss. Please refer to the following instructions for the soldering method of the plugs to ensure the expected level and keep the signal smooth. If you need further installation or operation guidance, please directly contact UNiKA’s dealer or distributor, or write to the following mail address for help:info@unikapro.com

PRODUCT OVERVIEW

• PRO 248 is an active dual-channel DI box. Unlike traditional DI, PRO 248 uses +48V phantom power instead of the traditional 9V dry cell battery, so users can use it on the mixer or external phantom power supply. Power is supplied to PRO 248, the power supply circuit and the output signal line are shared, and no additional power cord is required. The +48V indicators are set on the upper cover. The +48V circuit specially selects the British OEP PT-4 pulse transformer.
• PRO 248 has a pair of built-in UNiKA-PROTM EI30A10E 1+1:1+1 isolation transformers, which has a special copper foil layer and a dedicated ground layer, which allows this device to restore high signal/noise ratio and dynamic sound, and can avoid unnecessary leakage caused by radio frequency interference, ground interference and potential difference. PRO 248 is especially suitable for electronic musical instruments, recording studios and fixed installation projects by using mixers.
• The PRO 248 uses two TRS sockets on the input, and two TRS through out are convenient for musician to pass the direct signal to the instrument amplifier. In addition, it is equipped with a 0/-20dB attenuation switch and LED indicator, which is suitable for various types of audio signals with high and low impedance. The output terminal is also equipped with a GND/LIFT button to quickly eliminate ground noise.

CAUTION

This product has undergone rigorous inspection before leaving the factory. If customers encounter failures during use, please contact your local dealer or distributor for replacement or repairing, do not disassemble the case or replace parts by yourself, which will invalidate the warranty. For details, please refer to the warranty regulations in the enclosed warranty card, and fill in the details, and get a valid stamp or signature of the dealer or distributor.

PARAMETER TEST CONDITIONS

In the development and manufacturing process, Audio Precision’s 2700 series and 500 series are used to test and verify electrical characteristics.

FEATURES

• Power by external +48V phantom power
• Built-in UNiKA-PROTM EI30A10E isolation transformer
• Use British OEP PT-4 1:1 audio pulse transformer in phantom power circuit
• +48V status indicator on the upper cover
• The input socket uses a pair of TRS jacks
• Use a pair of TRS jacks as through out terminal
• At 0dB input, the set load impedance is 260KΩ, which can clearly show the high frequency overtones , harmonic and graininess of electric guitars or electric bass
• 50Ω ultra-low impedance output, suitable for various types of mixers and pre-amp equipment
• There is 0dB/-20dB input signal attenuation switch with status indicator
• The output is equipped with a GND/LIFT switch

APPEARANCE PARTS & FUNCTIONS

1. CH-1 signal output: XLR terminal, isolated balanced output of the transformer, need to turn on +48V phantom power supply for PRO 248 proper working after connecting to the mixer.

2. Output grounding/floating switch: when the switch is not pressed,the first pin (PIN-1) of XLR is grounded. PIN-1 will be disconnected from ground after pressing. This button should depend on the system. Used in the situation, in order to isolate the ground loop noise or leakage.

3. CH-2 signal output: XLR terminal, Isolated balanced output of the transformer, need to turn on +48V phantom power supply for PRO 248 proper working after connecting to the mixer.

4. +48V phantom power indicator: When CH-1 or CH-2 receive +48V phantom power, the indicator will be shinning the blue color.

5. CH-1/CH-2 Signal input: A pair of 6.35mm TRS sockets, can input balanced or unbalanced LINE signal.

6. PAD input attenuation switch: Provide 0/-20dB two options, when inputting signals of various impedances and levels.
   It can be attenuated by 20dB to avoid overload or clipping.

7. Attenuation active indicator: When the PAD attenuation switch is pressed (-20dB), the indicator light will be shinning the yellow color.

8. CH-1/CH-2 signal through out: Convenient for musicians musical instrument speakers or other DI and peripheral equipment.

ISO TRANSFORMER SCHEMATIC

UNiKA-PROTM EI30A10E

PULSE TRANSFORMER SCHEMATIC

OEP PT-4

INPUT PAD ATTENUATION

The most widely used DI box is to connect electronic musical instruments, sound source of A/V equipment and computers, convert their output signals into balanced signals and then extend the transmission distance. The most ideal state is to set the attenuator to 0dB position (button up) for musical instrument. For some other type of signals, you can press the button to make the signal is attenuated by 20dB to avoid clipping caused by signal overload. When the button is pressed, the PAD indicator on the right will light up. This attenuator acts on the input terminals of CH-1 and CH-2 at the same time.

POWER SUPPLY

PRO 248 is an active DI box and requires +48V phantom power. It can work normally when it is powered, but no additional power supply is required. Just use balanced wires to connect the device to the mixer’s input channel, and turn on the +48V power switch of the mixer, similar to connect a condenser microphone to the mixer. When the +48V power supply is suppling properly, the +48V ACTIVE indicator light on the upper cover will light up.

CAUTIONS: Before connecting the device, do not turn on the +48V switch of the mixer.

ELIMINATING GROUND LOOP NOISE

The built-in channel-independent balanced isolation transformer has solved the potential difference leakage problem. When the system causes a ground loop due to poor wiring, the noise can be eliminated through the GND/LIFT button. The GND/LIFT button determines whether pin 1 of the output XLR is grounded, grounded when it bounces, and disconnected from ground when pressed.

CONNECTION GUIDE

SPECIFICATIONS

(Specifications are subject to change without notice.)

Equipment

Manufacturer

• This declaration of conformity is issued under the sole responsibility of the manufacturer.

• The object of the declaration, Product: Direct box for musical instrument and A/V device.

• The object of the declaration described in point 4 is in conformity with the relevant
  Union harmonisation legislation: 2014/30/EU The Electromagnetic Compatibility Directive

• 6. References to the relevant harmonised standards used, or references to the specifications in relation to which conformity is declared:

EMI:|
---|---
EN 55032:2015| IEC 61000-4-3:2006+A1:2007+A2:2010
EN 61000-3-3:2014| IEC 61000-4-42012
EN 61000-3-3:2013| IEC 61000-4-5:2014+A1:2017
EMS:| IEC 61000-4-6:2013/CORE1:2015
EN 55035:2017| IEC 61000-4-8:2009
IEC 61000-4-2:2008| IEC 61000-4-11:2-4+A1:2017

• Where applicable, the above equipment will be tested and revision of existent certificate by WH Technology Corp. (TAF Accreditatio Number:2954) for compliance With EMC requirements set forth in the EUROPEAN COUNCIL DIRECTIVE 2014/30/EU and the technical standards mentioned above. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance.
• The technical file is available from the manufacturer at the address above Signed for and on behalf of: UNiKA Electronic Co.,Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>