UNI-T UT12C AC Voltage Detector User Manual
- June 4, 2024
- UNI-T
Table of Contents
UT12C AC
Voltage Detectors
Operating Manual
Warning:
Thank you for purchasing the UT12C test pencil and for the full use of the
product, please:
———-Read the user manual carefully.
———-strictly observe the safety rules and notes listed in the manual
Please note the following items to guard against electric shocking or personal
injury:
If any damage to the test pencil or failure to operate, please do not use it.
If any doubt, please deliver the test pencil for repair.
Please do not impose voltage exceeding the rating voltage on the test pencil.
There may be a danger of electric shock for voltage higher than 30V (AC),
please pay attention to that in operation and observe the local and national
safety codes of the country you are in.
Electric symbol
| Double insulation
---|---
| Be careful! Electric shocking
| Dangerous! Important information, reference manual
CAT IV equipment is intended for protecting from transient voltage injury
resulting from a first-level power source such as meters or overhead wires or
ground wires infrastructure.
The product meets
LVD (EN62020-031:2002; EN61010-1: 2001)
EMC (EN61326: 1997+A1: 1998+A2: 2001+A3: 2003)
Notes:
no contact with the white part of the front end of the pencil body for your
finger!
Working voltage and working condition
Working voltage: 90V-1000V AC
Working condition:
- Temperature: -10°C-50°C, storage: 10 °C-50°C Humidity: ≤95%
- Elevation: 3000m, cleaning: wet cloth
Operation instructions
Activate test pencil| Press once gently the button labeled with the power
symbol, buzzer, and LED and the motor will work concurrently for 0.5 seconds,
indicating the test pencil is activated successfully. While entering the test
standby status, LED will flicker two times continuously with an interval of
1.5 seconds.
---|---
AC voltage test| 1)Under non-vibration mode, put probe of test pencil close to
the object being tested with AC voltage, LED will flick and buzz
2)Under vibration mode, put probe of test pencil close to the object being
tested with AC voltage, LED will flick and buzz, and motor vibrate.
Power off automatically| The battery will power off automatically for energy
saving if do not use the test pencil for about 3 minutes Buzzer and LED will
work concurrently for 1 second, indicating power off successfully.
Stop using motor| Press the button gently after powering on, LED flickers
buzzer works, but the motor fails to vibrate, a mode called non-vibration
(shifting between vibration and non-vibration mode with button after power
on).
Stop using t est pencil| Press the button for about 2 seconds to power off the
test pencil with 1 second of the buzzer and LED light for 1 second.
Indication for low electricity of the battery
IV. Indication for low electricity of battery When the battery voltage is lower than 1.75V, the LED will flicker 5 times slowly after powering on, and the buzzer, if any signal, may sound faint, and the motor vibrates weakly. Please replace the battery immediately for test accuracy.
Battery replacement
Battery: 2×1.5V AAA
- with one hand holding the test pencil body, and the thumb of the other hand pressing the control position of the pencil head and extending it backward.
- Please take out the upper cover of the test pencil according to the direction shown in the picture, and replace the battery. (see the following picture)
Manufacturer:
Uni-Trend Technology(China) Limited
No 6, Gong Ye Bei 1st Road
Songshan Lake National High-Tech Industrial
Development Zone, Dongguan City
Guangdong Province
China Postal Code:523 808| Headquarters:
Uni-Trend Group Limited
Rm901, 9/F, Nanyang Plaza
57 Hung To Road
Kwun Tong
Kowloon, Hong Kong
Tel: (852) 2950 9168
Fax: (852) 2950 9303
Email: info@uni-trend.com
http://www.uni-trend.com
---|---
© Copyright 2011 Uni-Trend Group Limited. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>