wahoo SPEEDPLAY Advanced Pedal System User Guide
- June 6, 2024
- wahoo
Table of Contents
wahoo SPEEDPLAY Advanced Pedal System
IMPORTANT NOTICE
For safety, read this manual and all safety information thoroughly before assembly and use.
- Assemble the Speedplay Pedals & Cleats only as stated in the information contained in this manual.
- Do not modify the Speedplay Pedals & Cleats.
- All instructions can be viewed on our website: www.wahoofitness.com/instructions.
- Images may not reflect final product exactly.
The following instructions must be observed at all times in order to prevent personal injury and physical damage to equipment and surroundings. The instructions are classified according to the degree of danger or damage which may occur if the product is used incorrectly:
DANGER Failure to follow the instructions will result in death or serious injury.
WARNING Failure to follow the instructions will result in death or serious injury.
CAUTION Failure to follow the instructions could cause personal injury and/or physical damage to equipment or surroundings.
WARNING Follow the instructions provided in the manual when assembling the product.
BOX CONTENTS
A. BASE PLATES w/ 5-F & 5-R Shims (2x)
B. SHIM PACKET 6- F & 6-R Shims (2x), Extra Shims (2x)
C. CLEAT SURROUNDS (not included with COMP) 1 right / 1 left
D. **CLEAT COVERS*** 1 right / 1 left
E. **PROTECTOR PLATES*** 1 right / 1 left
F **. SPRING & HOUSING*** 1 right / 1 left
*Items ship pre-assembled. Separate Cleat Covers before installation.
G. SCREW PACKET Base Plate Screws: Short/Black (6x) & Long/Silver (6x), Protector Plate Screws (8x)
CLEAT INSTALLATION
CHOOSE THE SHIMS FOR THE BASE PLATE THAT BEST FIT THE SOLE OF THE SHOE
CAUTION The Base Plate/Shim Combo may not create a “perfect” fit to the bottom of the shoe, but for best results it is important to use the Shims that provide the “best” fit.
SCREW THE BASE PLATE TO THE SHOE USING THE BASE PLATE SCREWS
Base Plate Screws ship in two lengths: (Short/Black & Long/Silver) Use the shortest screws that allow at least five full turns of engagement with the socket in the sole of the shoe. Set the desired fore-aft position then tighten the Base Plate Screws. Recommended tightening torque: 4 Nm.
FIT THE CLEAT SURROUND AROUND THE BASE PLATE
FIT THE PROTECTOR PLATE TO THE SPRING & HOUSING
- Spring & Housings are labeled “LEFT” or “RIGHT”. Protector Plates are not labeled.
- The Spring & Housing ships pre-assembled to the Protector Plate. If they have separated, gently snap them together using the two small tabs as a guide.
SCREW THE ASSEMBLY TO THE BASE PLATE USING THE PROTECTOR PLATE
SCREWS
Install the Protector Plate Screws using a “Double X Pattern” (shown below).
Loosely engage all four Protector Plate Screws (Steps: A thru D).
Set the desired left-right position then tighten the Protector Plate Screws (Steps: E thru H). Recommended tightening torque: 2.5 Nm.
ADJUST THE LIMIT SCREWS TO SET THE DESIRED FLOAT
ADJUST THE LIMIT SCREWS TO SET THE DESIRED FLOAT
Tighten the Limit Screws to reduce the amount of float (“heel movement”)
experienced by the foot while pedaling. Housings are labelled “Heel In” &
“Heel Out” to guide which Limit Screws to adjust. Preferred float range is
unique to each rider. If you are unsure of your float preference, begin with
medium float and adjust as needed. Right Shoe Note: Do not unscrew the Limit
Screws from the Housing when adjusting float, and do not further tighten the
Limit Screws once they have made contact with the tip of the Spring.
FIT THE CLEAT COVER OVER THE EDGES OF THE PROTECTOR PLATE
Cleat Covers are labeled “LEFT” or “RIGHT”. Grip the shoe and apply force with the palm of the hand to each of the four corners to ensure that the Cleat Cover has properly covered the edges of the Protector Plate. The Cleat Cover should fit flush to the Cleat Surround when installed correctly. Note: Failure to properly complete this step may result in the Cleat Cover falling off.
APPLY PTFE DRY LUBE TO THE SPRING ˜OPTIONAL°
Reduce the engagement force required to clip into the pedals by applying a small amount of “PTFE Dry Lube” to the Spring. Wipe away any excess lube.
FOR FULL FEATURE DETAILS AND USER INSTRUCTIONS, GO TO: WAHOOFITNESS.COM/INSTRUCTIONS/SPEEDPLAY
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>