Changtaiwei Electronic M-8B Walkie Talkie User Guide

June 6, 2024
Changtaiwei Electronic

Changtaiwei
Electronic M-8B Walkie Talkie
User Guide

CAUTION
Read this operating instruction carefully before using your two-way radio, including the part on Product Safety and Important Notice.

1. Antenna
2. Backlit LCD Display
3. Menu/Power Button
4.. Antenna Call/Lock Button Up
5. Button
6. Microphone
7. Speaker
8. External Speaker/ Microphone/Charger Jack| 9. Down Button
10. Scan/Lamp Button
11. PTT(Pull to talk) Button
12. Lamp
13. Wrist Strap Connection
14. Belt Clip
15. Battery Compartment
16. Battery Door Latch
---|---

Product Features

Channel Frequency(MHz) Channel Frequency(MHz)
1 463. 12 468.
2 463. 13 468.
3 463. 14 468.
4 463. 15 462.5500
5 463. 16 462.5750
6 463. 17 462.6000
7 463. 18 462.6250
8 468. 19 462.6500
9 468. 20 462.6750
10 468. 21 462.7000
11 468. 22 462.7250

Installing Batteries
To install or replace batteries:

  1. Remove the belt clip by pulling the tab and sliding it up.
  2. Pull the battery door lock tab up to release the battery cover. Insert 3 “AA” batteries.
  3. Put the battery cover back into place. Snap the lock tab and belt clip back into place.

Do not mix old and new batteries
Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

Features

  • 22 Channels
  • 121 Privacy Codes (38 CTCSS codes/83 DCS codes
  • Hands-Free Operation (VOX)
  • Scan Channels, privacy codes
  • Backlit LCD Display
  • Call Alert Ten selectable tones
  • Button Lock
  • Speaker/Microphone/ Jack/Charge Jack
  • Roger Beep Selectable On/Off
  • Battery/Power Saver
  • Keystroke Tones
  • Battery Level Indicator
  • Low Battery Audible Alert
  • Auto Squelch
  • Belt Clip

Backlit LCD Display

1. Battery Level Indicator
2. VOX Icon
3. Scan Icon
4. Roger Beep Icon
5. Lock Icon
6. Low Power Icon| 7. DCS/CTCSS Icons
8. DCS/CTCSS Privacy Code Numbers
9. Power Saver Icon
10. Channel Numbers
11. Receive/Transmit Icon
12. Key Tone Icon
---|---

Maximum range may vary and is based on unobstructed line-of-sight communication under ideal conditions.

Quick Start

  1. Press and hold the Menu/Power button to turn on your radio.

  2. Press the Menu, Press the Up or Down button to select a channel.
    Both radios must be tuned to the same channel/privacy code to communicate.

  3. Press and hold the PTT button while speaking into the microphone.

  4. When finished talking, release the PTT button and listen for a response.

Turn on Your Radio Press and hold the Menu/Power button until you hear a series of audible tones indicating the radio is on. Your radio is now in Standby mode, ready to receive transmissions. The radio is always in Standby mode except when the PTT, Call or Menu/Power buttons are pressed.
Battery Low When battery power is low, the final bar in the Battery Low icon will blink and an audible tone will sound twice before the radio shuts off. Your batteries should be replaced or recharged if using rechargeable batteries.

The radio will display a flashing battery icon while charging.
For charging radios (A /Batteries: Just for batteries and adapter packaging option)

  1. To charge a single radio, simply insert the connector directly into the charge jack located on the bottom of the radio.
    The radio will display a flashing battery icon while charging. Recommends your radio be turned off while being charged.

Auto Battery Save
If there are no transmissions within 3 seconds, the radio will automatically switch to Battery Save mode and the Power Saver icon will display. This will not affect the radio’s ability to receive incoming transmissions.
Communicating with Another Person

  1. Press and hold the PTT button.
  2. With the microphone about two inches (2.5-5 cm from your mouth, speak in a normal voice.
  3. Release the button when you are finished PTT talking and listen for a response. You cannot receive incoming calls while pressing the button. PTT Both radios must be tuned to the same channel/privacy code to communicate.

To Select a Channel With the radio on, select any of the 22 channels by pressing Menu and the Up or Down button. Both radios must be tuned to the same channel to communicate.
Listening for a Response
Release the button to receive incoming PTT transmissions. Your radio is always in Standby mode while the PTT or Call buttons are not pressed.
To Adjust Volume Press the Up or at the standby mode. Down button, A double beep sound is used to indicate the minimum and maximum volume levels (1 through 8).
Call Button Press and release the Call button. The other person will hear a two-second call tone. This tone is used only to establish voice communications. See page 8 on how to select between ten call tone settings.
Lock Function
The Lock function locks the Channel Up, Channel Down, and Menu/Power buttons to prevent accidental operation.
To turn the lock on or off:
–Press and hold the Call/Lock button for two seconds.
A double beep sound is used to confirm your lock on or off request. When in Lock mode, the Lock icon will be displayed.
Scrolling Through the Menu Function
By scrolling through the MENU function, you will be able to select or turn on the preferred features of your radio. When scrolling through the Menu function, your radio features will be displayed in the same predetermined order: Set channels
Set CTCSS Privacy Codes
Set DCS Privacy Codes
Set Vox Sensitivity/Off
Set Call Tones 1-10
Set Roger Beep On/Off
Set Key Tones On/Off
Privacy Codes
Your radio incorporates two advanced coded squelch systems that can help to reduce interference from other users on any given channel. CTCSS (Continuous Tone Coded Squelch System) provides 38 privacy codes and DCS (Digitally Coded Squelch) provides 83 privacy codes. This provides a total of 121 Privacy Codes. Either system can be used on all channels, but both systems cannot be used on the same channel at the same time.
To successfully communicate using a privacy code, both the sending and receiving radios must be tuned to the same channel and to the same privacy code system (CTCSS or DCS) and privacy code number. Each channel will remember the last privacy code system and number you select. The privacy code 00 is not a privacy code, but allows all signals
to be heard on a channel that is set to 00 on both the CTCSS and DCS systems.
Set CTCSS Privacy Codes To select a CTCSS privacy code:

  1. After selecting a channel, press the Menu/Power button until the CTCSS icon appears and the small numbers next to the channel number flash on the display.
  2. Press using the Up or Down button to select a privacy code. You can hold the Up or Down button for fast advance.
  3. When your desired CTCSS privacy code is displayed, choose one of the following:
    a. Press the Menu/Power button to enter the new setting and proceed to other functions.
    b. Press the PTT button to enter the new setting and return to Standby mode.

Set DCS Privacy Codes

To select a DCS privacy code:

  1. After selecting a channel, press the Menu/Power button until the DCS icon appears and the small numbers flash on the display (01 through 83).
  2. Press using the Up or Down button to select a DCS privacy code. You can hold the Up or Down button for fast advance.
  3. When DCS privacy code is displayed, choose one of the following:
    a. Press the Menu/Power button to enter the new setting and proceed to other functions.
    b. Press the PTT button to enter the new setting and return to Standby mode.

Voice Activated Transmit (VOX)
In VOX mode, your radio can be used “hands-free,” automatically transmitting when you speak. You can set the VOX sensitivity level to fit the volume of your voice and avoid transmissions triggered by background noise. The current VOX sensitivity level is displayed with letters “ vox ” and a Number 1 through 3, with Number 3 being the most sensitive level and Number 1 being the least sensitive level.
2. Press the Up or Down button to change the setting3. Choose one of the following:
a. Press the Menu/Lock button to enter the new setting and proceed to other functions.
b. Press the PTT button to enter the new setting and return to Standby mode.
To turn VOX mode off:

  1. Press the Menu/Lock button until the VOX icon on the display.
  2. Press the Up or Down button to turn VOX Off. The current “00” setting is displayed.
  3. Choose one of the following:
    a. Press the Menu/Lock button to enter the new setting and proceed to other functions.
    b. Press the PTT button to enter the new setting and return to Standby mode.

Ten Call Tone Settings You can choose between ten different Call Tone Settings to transmit a call alert.
To change a call tone setting:

  1. Press the Menu/Power button until the letter “C” and the current call tone number (01 through 10) is displayed. The current call tone will sound for two seconds.
  2. Press the Up or Down button to hear the other call tone settings.
  3. Choose one of the following:
    a. Press the Menu/Power button to enter the new setting and proceed to other functions.
    b. Press the PTT button to enter the new setting and return to Standby mode.

Roger Beep Confirmation Tone
Your listener will hear an audible tone when you release the PTT button. This alerts the other party that you are finished talking and it is OK for them to speak.

To turn the roger beep on or off:

  1. Press the Menu/Power button until the Roger Beep icon
    . The current is displayed on or off setting flashes

  2. Press the Up or Down button to select roger beep on or off.

  3. Choose one of the following:
    a. Press the Menu/Power button to enter the new setting and proceed to other functions.
    b. Press the PTT button to enter the new setting and return to Standby mode.

Key Tone On/Off
When Key Tone is On, an audible tone will sound each time a button is pressed. To turn key tone on or off:

  1. Current key tone status On/Off will flash.
  2. Press the Up or Down button to select key tone on or off.
  3. Choose one of the following:
    a. Press the Menu/Power button to enter the new setting and proceed to other functions.
    b. Press the PTT button to enter the new setting and return to Standby mode.

Channel Scan
Your radio can automatically scan channels.
To scan channels:

  1. Press and release the Scan button until the Scan icon and the channel numbers appear on the display.
  2. Press and hold the Scan button to begin scanning channels. The radio ignores specific privacy codes while scanning channels. The Scan icon will continue to be displayed when scan is on. Your radio will continue to scan all channels and stop if an incoming transmission is detected. Your radio will remain on that channel for 10 seconds.
    During scanning (while receiving an incoming transmission), you can choose from the following:
    a. Press and hold the PTT button to communicate on that channel. Your radio will remain on that channel and return to Standby mode.
    b. Press the Channel Up or Channel Down button to resume scanning channels.
    c. Press and hold the Scan button to return to Standby.

Privacy Code Scan
Your radio can automatically scan the Privacy Codes (either CTCSS 01 through 38 or DCS 01 through 83) within one channel. Only one set of privacy codes (CTCSS or DCS) can be scanned at a time.
To scan privacy codes:

  1. While in Standby mode, press and release the Scan button twice (CTCSS) or three times (DCS) until the CTCSS or DCS icon and numbers are flashing.
  2. Press and hold the Scan button to begin scanning privacy codes within the selected channel.
    The Scan icon will continue to be displayed when the privacy code scan is on. Your radio will continue to scan privacy codes and stop as an incoming transmission is detected. Your radio will remain on that channel/privacy code for 10 seconds. During scanning (while receiving an incoming transmission), you can choose from the following:
    a. Press and hold the PTT button to communicate on that channel/ privacy code. Your radio will remain on that channel/privacy code and return to Standby mode.
    b. Press the Up or Down button to resume scanning privacy codes. If you do not press any button within 10 seconds, your radio will automatically resume scanning privacy codes.

Safety Information for Radios
Your wireless handheld portable transceiver contains a low-power transmitter. When the talk button is pushed, it sends out radio frequency (RF) signals.The device is authorized to operate at a duty factor not to exceed 50%.In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless devices.

Important

FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the FCC RF exposure guidelines when used with accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use only the supplied antenna. Unauthorized antennas, modifications or attachments could damage the transmitter and may violate FCC regulations.
Normal Position
Hold the transmitter approximately two inches (2.5-5cm) from your face and speak in a normal voice, with the antenna pointed up and away.

FCC Statement

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Warning
This equipment must be installed and operated in accordance with provided instructions and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. The SAR limit adopted by the US is 1.6 W/kg averaged over 1 gram of tissue. The highest SAR value for this device type when properly worn on the body is 0.68 W/kg.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals