evapolar EV-3000 Personal Air Cooler Instruction Manual
- June 15, 2024
- evapolar
Table of Contents
evapolar EV-3000 Personal Air Cooler
Dear customer, if you happen to have any questions or issues with your device, please reach out to us via amzn.to/3bGAXRi and we will get back to you with the best answer or solution!
SAFETY REGULATIONS
When using electrical appliances, basic safety precautions should always be
followed, including the listed below:
WARNING!
Use this device according to its intended purpose as described in this
booklet.
- This device is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the device by a person responsible for their safety.
- The device must be placed on a smooth horizontal surface.
- Tilting/turning upside down may cause a water leak and damage the device.
- Use only pure water without any additives to fill the device.
- Usage of other liquids is prohibited. Do not add any aromatic oils or any other odorous substances to the water.
- Disconnect the device before the following actions: cleaning, technical maintenance, removing/replacing elements, and moving the device.
- To fill the water tank with water, always remove it from the device first.
- Do not install a water tank with water without a cartridge inside.
- Remove the water tank and set the device to run at the maximum fan speed for at least one hour to dry the water out from the internal reservoir before taking out the cartridge.
- Do not take the cartridge out of the device unless it is done.
- Do not clean the device with gasoline, window-washing liquid, corrosive substances, or any organic solvent. The warranty does not cover damages caused by improper cleaning.
- In case of a leak or if water spills onto the surface of the device, immediately disconnect the power cord and let the device dry for at least 24 hours.
- We strongly recommend using the original power supply from the package.
- Disconnect all cords by holding the plugs and never pull on the cords themselves.
- To avoid possible damage to the device,
- do not let any foreign objects enter the device.
- do not place heavy items on top of the device.
- do not submerge the device in water or any other liquid (see cleaning guide below).
- do not subject the device to excessive shocks and vibrations.
- do not cover the operating device.
- do not leave the operating device unattended.
- Stop using the device if you notice an unusual sound or smell.
- This device contains a built-in Wi-Fi module. The RF signals may interfere with the functionality of sensitive devices. Keep the device at least 20 cm (8 inches) away from pacemakers.
DANGER!
- Do not open the upper cover of the device and/or remove any replaceable parts of the device while it’s in operation.
- Do not try to touch the fan or block it with any foreign objects while it’s in operation.
- Do not touch the power supply or power cord with wet hands.
- Do not place the device next to heating electrical equipment and other heat sources, including naked flames.
- Do not place the device upon or next to any other electronic devices (in case of leakage, there is a danger of a short circuit).
- Do not use the device while bathing or in the shower.
- Do not operate the device with a damaged cord or plug, if you notice it is not working properly, or if it has been dropped or damaged.
- Failure to heed the warnings above may result in damage to the device or injury. The manufacturer does not take any responsibility for any damage arising from failure to comply with this product guide.
- If you have not found a solution to your problem, please contact our support team (see page 22), do not try to fix the problem yourself. All repairs must be carried out by qualified service personnel.
In case you notice any malfunction, please check out our troubleshooting guide.
BASIC PRINCIPLES OF WORK
To enjoy a nice cool breeze on a hot day, you need:
- Well-ventilated room
- Relative humidity <70%
- 1300 ml (44 oz) of pure water
- Power supply 2.5A 5V
TO START THE DEVICE FOLLOW THE STEPS
Ensure the device is placed on a flat horizontal surface first.
FILLING WITH WATER
-
Slide the water reservoir up.
-
Open the lid and fill the reservoir with water.
-
Place the reservoir back onto the base. Make sure it is installed properly. The water will start flowing automatically.
-
Depending on the air temperature and humidity, the full reservoir should provide from 4 to 9 hours of uninterrupted cooling.
TIP: To extend the period before the next refill, you need to fill up the reservoir, wait until the cartridge is full of water (max.10 minutes), and then refill the reservoir once again. -
Use a laptop or PC/power bank/adaptor plugged into the socket as a power source. 2.5A 5V is a minimum requirement.
-
The Power button on the top of the device will light up. Press this button. The device will switch on with a short vibration. Use the top panel of the device to adjust device parameters.
-
Move the slider on the sidewall of the device to adjust the airflow direction.
-
Install the Evapolar Mobile App to control the evaSMART via your smartphone.
-
Connect evaSMART to Smart Home and see the full voice experience for managing the device. The temperature of the outgoing air will start to decrease in a few minutes. Enjoy your microclimate!
TIP: If you would like to feel a light pleasant aroma in your room, we have come up with an aroma clip, especially for you. Visit evapolar.com/en/shop to make a purchase.
TIP: If for any reason you are unable to connect your device to a direct power source (eg, while camping), you can use a power bank. Visit evapolar.com/en/shop to make a purchase .
CONTROL PANEL & MENU
MAIN SCREEN
During the first use, evaSMART runs with preset default parameters. After
being used and inputting your preferred settings, the device should run with
those settings automatically. Increase or decrease the fan speed by pressing
the Up/Down buttons, the values can be changed between 1% and 100%. Press and
hold the Up/Down buttons for quick setup.
MENU SCREEN
Use the Up/Down buttons to navigate (the selected option blinks), Press the OK
button to confirm your choice. To go to the main screen press the Power
button. In case the item/mode is unavailable, please, ensure your evaSMART has
the latest firmware version. The firmware version can be checked in the
Settings section of the mobile application. If you see the warning sign, the
firmware needs updating (see the WI-FI settings section below).
MENU ITEMS AND MODES
NIGHT MODE
In the night mode, LED lighting turns off and the display dims. To enable:
press OK, the device will automatically go into night mode. To disable: press
the OK button.
BRIGHTNESS SETTINGS
Select the item, and use the Up/Down buttons to change the values between 1%
and 100%. To decrease or increase the brightness quickly, press and hold the
Up/Down buttons; to turn off the water reservoir lighting set the brightness
to 0%. Confirm your choice by pressing OK.
LED LIGHTENING COLOR
You can choose your preferred lighting color for the water reservoir and
adjust its hue. Select the item, press and hold the Up/Down buttons to go
through the colors quickly. Confirm your choice by pressing OK.
COLOR PLAYLISTS MODE
In this mode, the water reservoir lighting gradually changes colors. Select
the item, press and hold the Up/Down buttons to go through the available color
playlists (each has its unique number). Confirm your choice by pressing OK.
SLEEP MODE
You can set your evaSMART to turn off the fan after a specific period. Select
the item, and press the Up/Down buttons to change the values. Confirm your
choice by pressing OK. To disable it set the value to 0.
WI-FI SETTINGS
A built-in Wi-Fi module allows you to control your EVA-SMART remotely. To pair
up your phone with evaSMART, you will need to first install the Evapolar
application on your smartphone. After that, you will need to register a new
user account and choose “evaSMART Model 3” when prompted. Finally, follow the
animated instructions on your phone screen to connect your phone to evaSMART.
You can also turn Wi-Fi on/off. Select the item from the list (the selected
item will blink), and confirm your choice by pressing OK.
To exit the settings, press the Power button. To connect, select the “Con” option. To disable Wi-Fi, select the “OFF” option (if “ON” is written on the screen, this means that Wi-Fi is turned off). To enable Wi-Fi, select the “ON” option (if “OFF” is written on the screen, this means that Wi-Fi is turned on).
CONNECTION STATUS ICONS
CARTRIDGE LIFESPAN INDICATOR
This mode lets you know when it’s time to replace the cartridge with the new
one. A new cartridge has 100%; when the value is close to 0%, the cartridge
needs to be replaced.
MEASUREMENT UNITS
Temperature can be displayed either in Celsius or Fahrenheit. To change the
measurement units, press and hold a combination of the Up/Down buttons on the
menu screen, then choose your option, Confirm your choice by pressing OK. This
settings option is also available in the mobile application (Settings
section).
LOW POWER ICON
If you see this icon, it means that the device receives insufficient power and
may malfunction. To avoid this, use the power adapter and the power cord that
comes with the device, or make sure that your power supply is 2.5A 5V.
SETTINGS RESTORE
To restore the settings, turn the device off (with the only Power button
visible on the screen) and press a combination of the Up and Down buttons (you
can press with your fingers or with your palm edge) and the Power button all
at once. Then press the Up button, and you will see the “Ur” (User set-tings
restore) letters blinking. Confirm your choice by pressing OK. You will see
the entire display turn on and off again. Done, settings restored.
REPLACING THE CARTRIDGE
Remove the water tank and set the device to run at the maximum fan speed for
at least one hour to dry the water out from the internal reservoir before
taking out the cartridge. Do not take the cartridge out of the device unless
it is done. sure the device has no water and is dry before installing a new
cartridge to prevent any water damage.
- Disconnect the device from the power source.
- Remove the reservoir by sliding it up.
- Pull out the safety panel to reach the cartridge.
- Take out the old cartridge by sliding it out.
- Place a new cartridge in place of the old one.
- Put the safety panel back to hide the cartridge.
- Put the reservoir back in place.
- The device is ready to use.
- Depending on usage and storage, the cartridge can last 3-6 months.
- Poor water quality reduces the lifespan of the cartridge.
MAINTENANCE: CLEANING, STORAGE, TRANSPORTATION
We strongly recommend drying the device totally before cleaning, storage, and
long-distance transportation. To do this, you need to empty the water tank and
set the device to run on the maximum fan speed for at least 4-5 hours to dry
the water out from the internal reservoir section.
CLEANING
The cleaning period depends on the level of dust in the area where you use your air cooler. The front grill and the internal area can be wiped with a soft cloth. A cleaning procedure can be carried out, when The device is dry The device is disconnected from the power source The cartridge is extracted Do not wipe the inside of the cartridge, just its outer plastic body.
STORAGE DURING LONG PERIODS OF NO USAGE
If you’re not intending to use the device for more than 5 days, we strongly
recommend the following:
- Dry the device and clean it (as described above).
- Place the device into an appropriately sized package for storage (the original package is recommended). Store the device in a dry space at room temperature.
TRANSPORTATION
Before any kind of transportation, the device should be disconnected from the
power source. Do not transport the device long distances with a wet cartridge;
please see the “Storage during long periods of no usage” section. For shorter
distances, make sure that the device with a wet cartridge is not isolated in a
box or bag with no airflow.
TROUBLESHOOTING
PROBLEM: Cold air does not come out of the device despite the fact the
cartridge is wet
POSSIBLE CAUSE 1: Humidity level over 70%
SOLUTION: Ventilate the room
POSSIBLE CAUSE 2: The cartridge has expired
SOLUTION: Replace the cartridge
PROBLEM: Cold air does not come out of the device and the cartridge seems
to be dry despite the fact the water tank is full SOLUTION: Tilt the device
slightly towards the water tank for a few seconds or shake gently to get rid
of the airlock. Please, contact our support team if that doesn’t help
PROBLEM: The device shows a Low power icon or reboots at irregular
intervals.
POSSIBLE CAUSE: The device does not receive enough power SOLUTION: Ensure
the power source for your EVSMART is 2.5A 5V. Please, contact our support team
if that doesn’t help
PROBLEM: The device suddenly started emitting an unpleasant odor
POSSIBLE CAUSE: Impurities in water or air absorbed by the filter
SOLUTION: Pour a full tank of clean, distilled water and let the device
completely dry out (this may take several times to remove the smell
completely)
PROBLEM: The device cannot connect to Wi-Fi
POSSIBLE CAUSE: Ensure the Connection mode (see pages 14-15) is enabled
and the Wi-Fi icon is blinking. Please, contact our support team if you
followed the steps carefully but that didn’t help
SPECIFICATIONS
EEE WASTE
Please, dispose of the cartridge and the device according to the state law.
LEGAL INFORMATION
The device complies with the requirements of EU Directives – 2014/ 35/EU Low
Voltage Directive and 2014/30/EU EMC Directive, as well as the following
European harmonized standards:
EN 55014-1:2006/ A1:2009/ A2:2011 – Electromagnetic compatibility.
Requirements for household appliances, electric tools, and similar apparatus
Part 1: Emission
EN 55014-2:2015 – Electromagnetic compatibility. Requirements
for household appliances, electric tools, and similar apparatus. Part 2:
Immunity. Product family standard
EN 61000-3-2:2014 Electromagnetic compatibility (EMC). Part 3-2: Limits.
Limits for harmonic current emissions (equipment input current ≤16 A per
phase)
EN 61000-3-3:2013 Electromagnetic compatibility (EMC). Part 3-3: Limits.
Limitation of voltage changes, voltage fluctuations, and flicker in public
low-voltage supply systems, for equipment with rated current ≤16A per phase
and not subject to conditional connection
EN 60335-1:2012/AC:2014/A11:2014 – Household and similar electrical
appliances. Safety. Part 1: General requirements— EN 60335 -2-40:2003/
A11:2004/ A12:2005/ C1:2006/ A1:2006/A2:2009/ C2:2010/ A13:2012/ A13/AC:2013 –
Household and similar electrical appliances. Safety. Part 2-40: Particular
requirements for electrical heat pumps, air-conditioners and dehumidifiers.
The device is marked by the sticker on the bottom of the case and contains the
following data: manufacturer’s name \ product name \ serial number \ year of
manufacture \ power settings (voltage, frequency, maximum power consumption,
weight) \ and CE marking.
References
- Amazon Sign-In
- Evapolar Coolers - Shop
- Evapolar - Cool Yourself With Portable Evaporative Air Coolers
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>