HAMPTON BAY 50200 Solar Path Light User Guide
- June 6, 2024
- HAMPTON BAY
Table of Contents
HAMPTON BAY 50200 Solar Path Light
Safety Information
WARNING: Your solar light may not function in temperatures below -4ºF (-20ºC) or above 140ºF (60ºC).
CAUTION: Use a rechargeable battery only. Recycle or dispose of batteries properly.
CAUTION: Do not open, short circuit, or mutilate batteries as injury may occur.
Warranty
ONE YEAR LIMITED WARRANTY
WHAT IS COVERED
The manufacturer warrants this product to be free of defects in material and
workmanship for a period of one (1) year from the date of purchase. This
warranty only applies to the original consumer purchaser and only to products
used in normal use and service. The manufacturer’s only obligation and your
exclusive remedy, is the repair or replacement of the product at the
manufacturer’s discretion, provided that the product has not been damaged
through misuse, abuse, accident, modification, alteration, neglect, or
mishandling. Proof of purchase and evidence of manufacturer’s date coding must
accompany all warranty claims. The manufacturer’s date coding is printed and
adhered to each product.
WHAT IS NOT COVERED
This warranty does not apply to products that are found to have been
improperly installed, setup, or used in any way not in accordance with the
instructions supplied with the product. This warranty does not apply to a
failure of the product as a result of an accident, misuse, abuse, negligence,
alteration, or faulty installation. Batteries supplied with this product are
not included in this warranty. This warranty shall not apply to the finish on
any portion of the product, such as surfaces and/or weathering, as this is
considered normal wear and tear.
The manufacturer does not warrant and specially disclaims any warranty,
whether express or implied, of fitness for a particular purpose, other than
the warranty contained herein. This warranty does not cover consequential or
incidental loss or damage, including but not limited to any labor/expense
costs involved in the replacement or repair of the product.
Contact the Customer Service Team at
1-830-249-1200 or CustomerService
@Creative-prc.us
Pre-Installation
PLANNING INSTALLATION
Ensure the mounting location for your solar light allows the solar panel to
receive direct sunlight. Do not locate the product in shaded areas as this
will significantly reduce performance.
Position the solar light such that during evening hours the ambient light from
other light sources does not affect the photosensor built into the solar
panel. High ambient light levels can cause the lamp to turn off during evening
hours.
NOTE: The solar light is equipped with a photosensor that turns the unit on at dusk and off at dawn. Ambient light can affect the operation of the photosensor.
TOOLS REQUIRED
PACKAGE CONTENTS
| Part | Description | Quantity |
|---|---|---|
| A | Top cap (pre-assembled) | 4 |
| B | Lamp housing (pre-assembled) | 4 |
| C | Pole | 4 |
| D | Ground stake | 4 |
| E | Battery (pre-assembled) | 4 |
Installation
Installing the light
IMPORTANT: Prior to use, remove the battery isolator tag (F) from the battery compartment and allow it to charge for a full sunny day.
NOTE: Do not use a hammer. If the ground is hard, use water to soften.
- Insert the ground stake (D) firmly into the ground at the installation location. If the ground is too hard, soak the ground with water to soften the ground or drive a metal rod or screwdriver into the ground to create a hole for the ground stake (D).
- Connect the pole (C) to the ground stake (D).
- Connect the lamp housing assembly (A & B) to the pole (C).
Maintenance
Replacing the battery
IMPORTANT: Dispose of the battery in accordance with local, state, and federal regulations.
IMPORTANT: When storing any solar product for an extended period of time, remove the batteries. Storing any solar product without regular recharge or removal of batteries could cause permanent damage to the rechargeable batteries.
NOTE: Use one AA-size, 1200mAh, 1.2V nickel-metal hydride rechargeable battery. For best performance, replace with a nickel-metal hydride rechargeable battery annually.
- Hold the lamp housing (B), and rotate the top cap (A) counterclockwise until it is loose. Then, remove the top cap (A) from the lamp housing (B).
- Remove the battery cover (G) and the old battery (E). Replace with a new nickel-metal hydride rechargeable battery. The recommended replacement battery capacity should be 1200 to1500mAh.
- Replace the battery cover (G). Place the top cap (A) back on the lamp housing (B), and rotate the top cap (A) clockwise until it locks in place.
Care and Cleaning
- The solar panel should be cleaned periodically with a damp cloth to help maintain optimum performance.
- Do not use any cleaners with chemicals, solvents, or harsh abrasives.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|
The nightly run time is short.
|
The battery is not fully charged.
| Ensure that the solar light is located in an area where it can receive the
maximum amount of full, direct sunlight every day. Keeping the solar panel
clean is equally important to ensure the maximum charging performance.
The battery is reaching the end of its useful life.| Replace the old battery
with 1.2V Nickel Metal Hydride rechargeable battery.
The solar light does not turn on at night.
| Your solar light contains a battery isolator tag in the battery compartment.
This isolator tag must be removed prior to use.| Prior to use, ensure that the
battery isolator tag has been removed from the unit and the unit is allowed to
charge for a full sunny day.
The solar light is installed close to other light sources, which may keep the
solar light from turning on at night automatically.| Relocate the fixture or
eliminate other light sources.
Questions, problems, missing parts? Before returning to the store, call
Customer Service
8 a.m. – 6 p.m., EST, Monday-Friday
1-830-249-1200
CustomerService@Creative-prc.us
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>