ZAGG 103104651 Rugged Messenger – Backlit Case and Bluetooth Keyboard User Guide
- June 6, 2024
- ZAGG
Table of Contents
Quick Start
rugged messenger
Welcome
Instruction Manual: Congratulations on purchasing the ZAGG Rugged Messenger. The following will show you how to get started. Keep this quick start guide for future reference. For a full instruction manual, please visit zagg.to/instructions.
Getting Started
-
Inserting Your Device: First, insert your device at an angle such that the power and volume control buttons fit into their respective cutouts on the Rugged Messenger cover. Please note: Because the power and volume control buttons on the device sit higher than on other devices, take extra care when inserting it into the Rugged Messenger cover. Next, set the rest of your device into the cover and press it in. Press all-around your device to ensure it has seated properly.
-
Using the Stand: First, lift the cover off the keyboard and lay it flat. Then place your device in the magnetic recessed groove located in the middle of your Rugged Messenger where you will feel it connect with the magnets. Next, while holding your device in place, fold the cover towards your device. Let the cover fold in along the groove to create the built-in stand. Place the end of the cover close to the top of your device and you will feel the magnets connect, securing the stand in place. You can now rest your device against the stand at a convenient viewing angle.
-
Adjusting the Viewing Angle: Your Rugged Messenger case features built-in magnets that work together with the built-in stand to create multiple viewing angles. To adjust the viewing angle on your Rugged Messenger, simply slide the built-in stand up or down along your Rugged Messenger case until you feel the magnets connect.
-
Power: Open the Rugged Messenger and press the Power button located at the top right corner of the keyboard. A light will illuminate, indicating the power is now on. To tum off your Rugged Messenger, press and hold the Power button for three seconds.
-
Pair: Tum on your iPad’s Bluetooth® connection. Press your Rugged Messenger’s Bluetooth® ( ) key for three seconds. The LED above the Bluetooth® key being used will light and then pulse until pairing is complete. Select “ZAGG Keyboard” from your tablet’s list of available pairing devices. Repeat this process using the other Bluetooth® Key to pair your Rugged Messenger to another device. Once you have multiple devices paired, you can toggle your Rugged Messenger keyboard between the devices by pressing
ZAGG® and Rugged Messenger™ are trademarks of ZAGG Intellectual Property Holding Co., Inc. iPad® is a trademark of Apple Inc., registered in the U.S. and other countries.
Additional Functions
Keyboard Shortcuts: Your Rugged Messenger keyboard has all of the special function keys you know and love, plus some additional ones you’ll enjoy. Here are some of the most popular. For a complete list of functions, including a full instruction manual, visit zagg.to/instructions.
Home: Displays your device’s home screen.
Keyboard Hide/Show: Hides or shows your on-screen keyboard. Press this
before using Case mode so you can type without the keyboard.
Battery: Press fn + to check your Rugged Messenger’s remaining battery
level. The LED will light one of three ways: Three flashes indicate 50% or
more battery remaining. Two flashes indicate approximately 25% to 50% battery
remaining. One flash indicates 25% or less battery remaining. The LED will
flash once every two minutes to indicate critically low battery.
Backlights: Press fn + to tum your Rugged Messenger’s backlights on.
Continue pressing to cycle through the three brightness settings or to tum the
backlights off.
Change Colours: Pressfn + to cycle through the seven backlight colours.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by ZAGG Inc is under license. Other trademarks and trade names are those of their respective owners.
FCC Caution：
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>