WARING COMMERCIAL WSM10L 10 Quart Stand Mixers User Manual

: June 6, 2024
: WARING COMMERCIAL

10.0-QUART/20.0-QUART STAND MIXERS

WSM10L/WSM20L
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.

IMPORTANT SAFEGUARDS

When using an electrical appliance, especially when children are present, basic safety precautions should always be taken to reduce the risk of fire, electric shock, and/or injury, including the following:

READ ALL INSTRUCTIONS.
Switch off and unplug before fitting or removing tools and/or attachments, after use, and before cleaning.
Close supervision is necessary when any appliance is used by or near children or individuals with certain disabilities. Waring does not recommend the use of this appliance by children.
Avoid contact with moving parts and fitted attachments. Keep hands, hair, clothing, as well as spatulas, and other utensils away from beaters during operation to reduce the risk of injury to persons and/or damage to the mixer.
The use of attachments not recommended or sold by Waring may cause fire, electric shock, or injury.
Do not use more than one attachment at a time.
Do not exceed the maximum capacities listed in this use and care instruction book.
Do not use the stand mixer if it is damaged or if the cord is damaged. Have the stand mixer checked and serviced before resuming use.
When using an attachment, make sure that you have read the safety instructions that come with the particular attachment.
Do not use outdoors.
Keep stainless steel bowls away from heat sources, such as stovetops, ovens, or microwaves.
To protect against the risk of electric shock, do not put the power unit in water or other liquids.
Remove all attachments and accessories from the stand mixer before washing.
Do not let the cord hang over the edge of the table or counter.
Do not put your hands into the bowl during operation.
The mixer should be mounted on a stable and clean surface. Keep it away from overheated or very wet places, and away from equipment that has strong electromagnetism or can produce a strong electromagnetic field.
Keep the machine clean.
Disconnect power supply before performing maintenance.

SAVE THESE INSTRUCTIONS
FOR COMMERCIAL USE ONLY

NOTE: The maximum rating is based on the attachment that draws the greatest power. Other recommended attachments may draw significantly less power.
WARNING: RISK OF FIRE OR ELECTRIC SHOCK

The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated, dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of fire or an electric shock to persons.
****The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

|

WARNING
RISK OF FIRE OR ELECTRIC SHOCK I DO NOT OPEN

|
---|---|---
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY

WARNING

GROUNDING INSTRUCTIONS

This appliance must be grounded while in use to protect the operator from electric shock. The appliance is equipped with a 3-conductor cord and a 3-prong, grounding-type plug to fit the proper grounding-type receptacle. The appliance has a plug that looks like the plugin drawing (1). An adapter, as in drawing (2), should be used for connecting the appliance plug to two-prong receptacles. The grounding lug, which extends from the adapter, must be connected to a permanent ground, such as a properly grounded outlet box as shown in drawing (3), using a metal screw. If the unit needs to be hardwired, have a licensed electrician connect the unit to a power supply.
GROUNDING METHOD

SPECIAL CORD SET INSTRUCTIONS

A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord. Longer extension cords are available and may be used if care is exercised in their use.
If a long extension cord is used, the marked electrical rating of the extension cord must be at least as great as the electrical rating of the appliance, and the longer cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over.

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong, grounding-type plugs and 3-pole cord connectors that accept the plug from the appliance. Use only extension cords that are intended for indoor use. Use only extension cords having an electrical rating not less than the rating of the appliance. Do not use damaged extension cords. Examine the extension cord before using it and replace it if damaged. Do not abuse the extension cord and do not yank on any cord to disconnect. Keep the cord away from heat and sharp edges.

PARTS & ACCESSORIES

START Button
STOP Button
Attachment Hub
Attachment Hub Screws
Bowl-Lift Lever
Bowl Guard Handle
Planetary Shaft
Bowl Handle
Bowl Clamp
Speed Control
Bowl Guard
Bowl
Rubber Feet
Bowl Cradle
Power Cord (NOT SHOWN)

INSTALLATION UNPACKING

Unpack the mixer immediately after receipt. If the machine is found to be damaged, save the packaging material and immediately contact your source of the equipment.
WARNING

TO AVOID SERIOUS PERSONAL INJURY:

ALWAYS install equipment in the work area with adequate light and space.
ONLY operate mixer on a solid, LEVEL, nonskid surface that is nonflammable.
NEVER bypass, alter, or modify this equipment in any way from its original condition. Doing so can create hazards and will void the warranty.
NEVER operate mixer without all warnings attached.
DO NOT attempt to lift the mixer alone.

INSTALLATION

Read this manual thoroughly before installation and operation. DO NOT proceed with installation and operation if you have questions or do not understand everything in this manual. Contact your local representative first.
Remove the corrugated box from the skid by removing the bands on the box. NOTE: The WSM10L and WSM20L are shipped in a wooden crate; only the bolts at the bottom of the crate on all four sides need to be removed.
Carefully unbolt the mixer from the skid using an 11/16″ or 3/4″ wrench.
Select a location for the mixer, keeping these points in mind:
• Floor or counter must be level.
• Easy access for maintenance and service.
• Clearance for operating controls, installing and removing agitators, bowls,s or attachments.
• Sufficient space for adding ingredients during mixing periods.
• Make sure rear ventilation outlet of mixer is not blocked.
Use at least two other people to tilt the unit and install rubber feet.
Inspect mixer to make sure all parts have been provided (i.e., bowl, paddle, whisk, and dough hook).
Read the electrical information found on the data plate located at the rear of the machine. The incoming power must match the rating on the data plate.

WARNING

OPERATING INSTRUCTIONS

TO AVOID SERIOUS PERSONAL INJURY:

Before using clean the mixer. Refer to the Cleaning Instructions section of this manual.
• NOTE: It is normal for the factory to apply a generous amount of grease in and on the machine. Excess grease (brown in color) will be on all metal surfaces (e.g., the top portion of bowl guard, speed control, bowl clamps, bowl-lift lever, and attachment hub thumbscrew). Excess high-pressured grease (brownish-black) can also be found on the planetary shaft, and some drippings can be found in the bowl.
DO NOT operate the mixer before reading the instruction manual first.
ALWAYS disconnect or unplug electric power before cleaning, servicing, or adjusting parts or attachments.
ALWAYS keep hands, hair, and clothing away from moving parts.
Turn off the mixer before changing speeds.
Follow the Capacity Chart for mixing dough. Refer to the Capacity Chart section.
Use only the first (1) speed for mixing dough. 2nd speed must never be used on 50% AR or lower.
If the unit shuts off during mixing (overload protection trips), reduce the batch size.

ABOUT THE REMOVABLE BOWL GUARD
(Models WSM10L and WSM20L)

The interlocking bowl guard is easy to remove and reattach for easy cleaning in a sink or dishwasher.
NOTE: When the bowl guard is open or not properly installed, the mixer will not operate.
NOTE: Rotate bowl guard clockwise (open) and counterclockwise (closed) to attach agitators to the mixer.
Opening/Rotating Bowl Guard:
Rotating bowl guard clockwise (open) and counterclockwise (closed), allows the operator to easily add ingredients to, and to properly remove the agitator and bowl from mixer.
Removing and Attaching the Bowl Guard:
NOTE: Before removing or attaching the bow guard, make sure the bowl is in the down/ lowered position and the agitator tool is off the shaft.

ATTACHING BOWL TO MIXER

Lower cradle by pulling lift lever forward and down to its resting position.
Lift bowl by bowl handles and:
a) Slowly position the locking pin (located on the rear of the bowl) into the hole in the middle rear of the cradle (Fig. 1).
b) Lower bowl onto pins located on either side of bowl cradle.
Once the bowl is positioned on the cradle, secure the bowl by pulling each bowl clamp forward until the bowl is locked tight (Fig. 2).

ATTACH AGITATOR TO MIXER
(i.e., Beater, Mixing Paddle, Dough Hook, Whisk)
Install bowl BEFORE attaching agitator.
NOTE: It is easier to install the agitator before adding the ingredients into the bowl.

Rotate the bowl guard to the left, so it rests in the open position. Using excessive force to open and close the bowl guard can damage the spring lock and bowl guard microswitch, and WILL VOID the warranty.
Slide the agitator slowly upward onto the planetary shaft, fitting the shaft pin through the slot in the agitator (Fig 3).
Rotate the agitator clockwise to secure it onto the planetary shaft. **

**

CAUTION

**MIXING INGREDIENTS

**

Overloading or not following the capacity chart will damage the mixer and void the warranty. Refer to the Capacity Chart section.
Before starting the mixer: Always change to the desired speed BEFORE starting the mixer. Failure to do so can damage the gears or other parts and WILL VOID the warranty.
Agitators must always rotate in a counterclockwise direction around the bowl. If the agitator moves clockwise, contact a licensed electrician immediately to remedy incorrect wiring.
IMPORTANT: It is recommended to always start with Speed 1 when starting the mixer. Failure to do so can damage the gears or other parts.

Add the appropriate mixing ingredients to the bowl.
Rotate bowl-lift lever up, until the bowl locks into position.
Rotate bowl guard to the right, until it locks into the closed position. You will hear it click into place.

NOTE: Mixer will not start if bowl guard is open or bowl is in the lowered position.

** CAUTION**

SETTING AND CHANGING SPEED

Three fixed speeds are available for use: first (1), second (2), and third (3).
IMPORTANT: When mixing product, it is recommended to follow the Capacity Chart on page 15.
Select the appropriate speed setting by lifting or lowering the speed control lever.
IMPORTANT: When mixing products, always follow the recommended agitator and speed setting according to the Capacity Chart. Refer to the Capacity Chart section.
Press the green START button to begin mixing.

CAUTION

Always STOP mixer BEFORE changing speeds. Failure to do so can damage the gears or other parts and WILL VOID the warranty! To change the speed while mixing:

a. Press the red STOP button, then wait for the agitator to come to a complete stop.
b. Change the speed by raising or lowering the speed control lever.
c. Press the green START button to restart the mixer.
NOTE: Mixer is equipped with motor overload protection. If a mixer shuts off during operation: Press the STOP button, unplug the unit from the wall, wait two minutes and plug the unit back into the wall. Press the overload reset button located on the back of the mixer.
NOTE: Reduce batch size by 10% if using chilled flour, water below 70˚F, ice, or high-gluten flour.
When the ingredients have been thoroughly mixed, press the red STOP button to stop the mixer.
Lower bowl by pulling bowl-lift lever forward and down to its resting position.
Rotate the bowl guard to the left, so it is in the open position.
Remove the agitator from the planetary shaft by lifting it upward, then rotating it counterclockwise until it is unlocked. Lower the agitator and remove it from the planetary shaft.
Push each bowl clamp backward to unlock the bowl from the bowl cradle.
Lift up slightly on a bowl, so it clears pins on the bowl cradle.
** CAUTION**

Most batches are heavy. Always use two people to remove and transport the loaded bowl after mixing is complete.

CLEANING INSTRUCTIONS

Dilute detergent per supplier’s instructions.
DO NOT hose down or pressure-wash mixer.
NEVER use a scrubber pad, steel wool, or abrasive material to clean the mixer.
NEVER use bleach (sodium hypochlorite) or bleach-based cleaner.
ALWAYS remove the agitator after each batch, as the agitator can become stuck on the shaft and will be difficult to remove.

CAUTION

The entire mixer, including removable parts, must be thoroughly cleaned and sanitized using the procedures identified by your local health department and the ServSafe Essentials, published by the National Restaurant Association Educational Foundation (NRAEF). Visitwww.servsafe.com for more details.
ALWAYS DISCONNECT OR UNPLUG ELECTRICAL
POWER FROM THE MIXER BEFORE CLEANING.

CLEANING INSTRUCTIONS

PART	REQUIRED ACTION	FREQUENCY
Agitators	Hand-wash using mild soap and water; rinse, dry, and sanitize.

Clean after each use.
Removable Bowl Guard| Hand-wash using mild soap and water; rinse, dry, and sanitize or place in dishwasher.| Clean after each use.
Bowl| Using a sponge or cloth, mild soap, and water, apply pressure to make sure the bowl is clean; rinse,

dry, and sanitize. The bowl can also be placed in a dishwasher.

| Clean after each use.
Rear Splash Guard| Hand-wash using mild soap and water; rinse, dry, and sanitize.| Clean after each use.
Bowl Cradle| Hand-wash using mild soap and water; rinse, dry, and sanitize.| Daily
Planetary Shaft| Wipe with a clean damp cloth; dry and sanitize. Apply a light quantity of Waring oil (mineral oil) to the planetary shaft after cleaning.| Clean after each use.
Exterior| Hand-wash using mild soap and water; rinse, dry, and sanitize. DO NOT use a water hose.| Daily

IMPORTANT POINTS

Waring mixer will provide years of uninterrupted service if you do the following:

RECOMMENDED MAINTENANCE

PART	REQUIRED ACTION	FREQUENCY
Bowl Slide	Apply Waring oil (mineral oil) on bowl slide. Raise and lower bowl
to distribute the oil onto the rods.	If bowl becomes difficult to raise or

lower.

NOTE: Any other servicing should be performed by an authorized service representative.

MIXER CAPACITY CHART

The following maximum capacities are intended as a guideline only. Varying factors, such as the type of flour used, the temperature of water used and other conditions may require the batch to be reduced.
When mixing dough (pizza, bread, or bagels) check your “AR”– absorption ratio – water weight divided by flour weight.
Below capacities based on 12% flour moisture at 70˚F water temperature.
If high-gluten flour is used, reduce dough batch size by 10%.
2nd speed should never be used on mixtures with less than 50% AR.
Do not use attachments on the hub while mixing.
When calculating the correct size mixer for your application, some helpful weights and measures to follow: 8.3 lb. = 1 gallon water & 2.0 lb. = 1 quart.

CAPACITY CHART & SUGGESTED SPEED CONTROL

PRODUCT DESCRIPTION| ATTACHMENT| AGITATOR| SPEED| 10-QUART| 20-QUART
---|---|---|---|---|---
**** Final bread and roll dough weight|

| Flat beater| 1| 9 lb.| 20 lb.
*** Mashed potatoes|

| Flat beater| 1| 10 lb.| 17 lb.

Cake batter

|

| Flat beater| 1| 8 lb.| 20 lb.
**** Waffle or hotcake batter|

| Flat beater| 1| 8 lb.| 20 lb.
**** Pound cake batter|

| Wire whisk| 3| 2 doz.| 3 doz.
**** Meringue|

| Wire whisk| 2| 3 qt.| 6 qt.

With butter and cream

NOTE: The mixer capacity depends on the moisture content of the dough. When mixing doughs (pizza, bread, or bagel) check your AR%(% Absorption Ratio) = Water weight divided by flour weight. The capacities listed on page 15 are based on flour at room temperature and 70°F water temperature. (1 gallon of water weighs 8.33 lb.)

LIMITED ONE YEAR WARRANTY

(U.S. & Canada Only)

Waring warrants every new Waring® Commercial Stand Mixer to be free from defects in materials and workmanship for a period of one year from the date of purchase when used with foodstuffs, nonabrasive liquids (other than detergents), and nonabrasive semiliquids, providing it has not been subject to loads in excess of the indicated rating. Under
this warranty, Waring will repair or replace any part which, upon our examination, is defective in materials or workmanship, provided the product is delivered prepaid to the Waring Service Center at 314 Ella T. Grasso Ave., Torrington, CT 06790, or any Factory Approved Service Center. This warranty does not: a) apply to any product that has become worn, defective, damaged, or broken due to use or due to repairs or servicing by other than the Waring Service Center or a Factory Approved Service Center, or due
to abuse, misuse, overloading or tampering; or b) cover incidental or consequential damages of any kind.
Warning: This warranty is void if the appliance is used on
Direct Current (DC).
WARING COMMERCIAL
314 Ella T. Grasso Ave.
Torrington, CT 06790

TROUBLESHOOTING

PROBLEM	POSSIBLE CAUSES	ACTION REQUIRED
Mixer will not operate	Bowl guard is not in the closed position.

Rotate the guard to the right until fully closed.
Bowl was not raised.| Raise a bowl to the highest position.
Power is not connected properly.| Check all power connections. Plug into

a live socket. (Do not use an extension cord!) Test socket with another item.

Building circuit breaker is off.| Check breaker box.
Internal overload tripped.| Press the STOP button, then press the reset button located on the back of the mixer. Wait two minutes. Then press START to restart the mixer. (If overload continues to trip, reduce batch size and/or adjust recipe!)
Gear is not engaged.| Switchgear fully into position. (Mixer will not operate if the speed control lever is positioned in-between speeds.)
Mixer stops during the mixing cycle| Internal overload tripped.| Press the STOP button, then press the reset button located on the back of the mixer. Wait two minutes. Then press START to restart the mixer. (If overload continues to trip, reduce batch size and/or adjust recipe!)
Mixer is noisy| Mixer is not installed on a level surface.| Adjust surface or relocate mixer. Make sure rubber feet are installed.
Bowl is not seated correctly or the clamps are not in place.| Make sure the bowl is seated into the bowl cradle correctly, and bowl clamps are locked into place.
Agitator not fitted properly.| Remove and attach the agitator into position properly.
Overloading bowl.| Reduce batch size. Refer to the Capacity Chart section.
Safety guard seized (will not move freely)| | Clean & lubricate slide sheath.
Agitators won’t go onto the planetary shaft easily| Lack of lubrication and/or cleaning of the planetary shaft.| Wipe planetary shaft with a clean, damp cloth and lubricate the shaft with mineral oil or food-quality grease.
Bowl lift sticking or not operational| Lack of lubrication on bowl slides.| Lubricate bowl slides with mineral oil or food-quality grease. If still sticking, the technician must clean the bowl-lift mechanism
One or more gears not working| Damaged or broken gear.| Technician to replace gear. Always stop the mixer before shifting gears!
Mixer will not mix medium or heavy loads| Incorrect or low voltage.| Contact electrician.
Residue leaking from the hub| Contaminated hub due to buildup of meat and/or vegetable juices (especially tomatoes).| Technician to remove the hub and clean the interior. To avoid problems, wipe hub and dry after each use. *Note: Acid from tomato juices will corrode/contaminate interior parts!
---|---|---
Agitators touching bottom or sides of bowl| Defective or dented bowl.| Remove dents or replace bowl.
Defective agitator.| Replace agitator.
Broken whip wires| Batch size is too large for the mixer. Adjust recipe.| Reduce batch size. Refer to Capacity Chart section. Mixture too firm, speed too high. Reduce speed.
Hand utensil dropped into the bowl while mixing.| Stop mixer.
Broken flat beater| Ingredients too cold or too large (e.g., frozen butter, cream cheese cut in chunks).| Wait for ingredients to reach room temperature before mixing.

Reduce chunk size.

Broken dough hook| Batch size is too large for the mixer.| Reduce batch size. Refer to the Capacity Chart section. Adjust recipe.
Ingredients too cold or too large.| Wait for ingredients to reach room temperature before mixing. Reduce chunk size.
Discoloration of mixed product| Bowl has not been thoroughly cleaned.| Clean bowl again. Refer to the Cleaning Instructions section.

Trademarks or service marks of third parties used herein are the trademarks or service marks of their respective owners.

©2019 Waring Commercial
314 Ella T. Grasso Ave.
Torrington, CT 06790
www.waringcommercialproducts.com
Printed in China
WSM10L/WSM20L IB
19WC060025
IB-16212

Documents / Resources

| WARING COMMERCIAL WSM10L 10 Quart Stand Mixers [pdf] User Manual
WSM10L, WSM20L, WSM10L 10 Quart Stand Mixers, 10 Quart Stand Mixers, Stand Mixers, Mixers, 20.0-Quart Stand Mixers
---|---