greenworks 60TB16 60V X-Range Bike Handle String Trimmer User Manual

greenworks 60TB16 60V X-Range Bike Handle String Trimmer

DESCRIPTION

PURPOSE
This machine is used to cut grass, light weeds, and other similar vegetation at or around ground level. The cutting plane must be approximately parallel to the ground surface. You cannot use the machine to cut or chop hedges, shrubs, bushes, flowers and compost.

OVERVIEW

1. Battery release button Carrying strip
2. Trigger
3. Auxiliary handle
4. Speed button/lock-out button On/off button
5. LED indication
6. Reverse button
7. Shaft
8. Guard
9. Cut-off blade

PACKING LIST

1. String trimmer bare tool
2. Auxiliary handle
3. Guard
4. Wrench
5. Shoulder harness
6. Operator manual

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING (THIS POWER TOOL)

WARNING
Read and understand all instructions before using this product. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

• Use only identical manufacturer’s replacement parts and accessories. Use of any other parts may create a hazard or cause product damage.
• Always wear safety glasses with side shields marked to comply with ANSI Z87.1. Everyday glasses have only impact resistant lenses. They are NOT safety glasses. Following this rule will reduce the risk of eye injury. Use face mask if operating in dusty work spaces.
• Avoid Dangerous Environment – Don’t expose power tools to damp or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Don’t use in rain.
• Keep all bystanders, children, and pets at least 50 ft. away.
• Dress Properly – Do not wear loose clothing or jewelry. They can be caught in moving parts. Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.
• Use right Appliance. Do not use appliance for any job except that for which it is intended.
• Avoid Unintentional Starting – Don’t carry appliance with finger on switch. Be sure switch is off when battery is plugged in.
• Don’t Force Appliance – It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.
• Don’t overreach – Keep proper footing and balance at all times.
• Stay alert – Watch what you are doing. Use common sense. Do not operate this unit when you are tired, ill or under the influence of alcohol, drugs or medication.
• Always store idle power tools indoors – When not in use, power tools should be stored indoors in a dry and high or locked up place, out of reach of children.
• Maintain Appliance With Care – Replace string head if cracked, chipped, or damaged in any way. Be sure the string head is properly installed and securely fastened. Keep cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow instructions for lubricating and changing accessories. Inspect appliance cord periodically, and if damaged, have it repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease. Failure to do so can cause serious injury.
• Check damaged parts before using the appliance, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, damaged mountings, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this manual.
• Remove or disconnect battery before servicing, cleaning or removing material from the gardening appliance.
• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care. Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. Use only Greenworks 60BA02/60BA25/60BA03/ 60BA04/60BA05/60BA06/ 60BA08 battery or other BAC series.
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. Use only Greenworks 60DP10/606P14 charger or other CAC series.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause a fire.
• Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
• Keep guards in place and in working order.
• Keep hands and feet away from cutting area.
• Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
• Use only with the nylon cutting line of 0.095″ (2.4 mm) diameter. Do not use heavier lines than recommended by the manufacturer and line materials of other types – for example, metal wire, rope, and the like.
• Be aware of blade thrust :
• Blade thrust may occur when the spinning blade contacts an object that it does not immediately cut.
• Blade thrust can be violent enough to cause the unit and/or operator to be propelled in any direction, and possibly lose control of the unit.
• Blade thrust can occur without warning if the blade snags, stalls or binds.
• Blade thrust is more likely to occur in areas where it is difficult to see the material being cut.
• Condition of Unit before Use – The handles shall be mounted in accordance with the manufacturer’s instructions. Do not attach any blade to a unit without proper installation of all required parts. Failure to use the proper parts can cause the blade to fly off and seriously injure the operator and/or bystanders. Discard blades that are bent, warped, cracked, broken, or damaged in any way. Use a sharp blade. A dull blade is more likely to snag and thrust.

SYMBOLS ON THE MACHINE

Some of the following symbols can be used on this machine. Please study them and learn their definition. Proper interpretation of these symbols will let you operate the tool better and safer.

RISK LEVELS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

avoided, will result in death or serious injury.
| WARNING| Indicates a potentially hazard- ous situation, which, if not avoided, could result in death or serious injury.
| CAUTION| Indicates a potentially hazard- ous situation, which, if not avoided, may result in minor or moderate injury.
| CAUTION| (Without Safety Alert Sym- bol) Indicates a situation that may result in property dam- age.

SERVICE
Servicing requires extreme care and knowledge and must be performed only by a qualified service technician. For service we suggest you return the machine to your nearest AUTHORIZED SERVICE CENTER for repair. Use only identical manufacturer’s replacement parts and accessories.

ENVIRONMENTALLY SAFE BATTERY DISPOSAL

The toxic and corrosive materials below are in the batteries used in this machine: Lithium-Ion, a toxic material.
WARNING
Discard all toxic materials in a specified manner to prevent contamination of the environment. Before discarding damaged or worn out Li-ion battery, contact your local waste disposal agency, or the local Environmental Protection Agency for information and specific instructions. Take the batteries to a local recycling and/or disposal center, certified for lithium-ion disposal

WARNING
If the battery pack cracks or breaks, with or without leaks, do not recharge it and do not use. Discard it and replace with a new battery pack. DO NOT TRY TO REPAIR IT! To prevent injury and risk of fire, explosion, or electric shock, and to avoid damage to the environment:

• Cover the terminals of the battery with heavy-duty adhesive tape.
• DO NOT try to remove or destroy any of the battery pack components.
• DO NOT try to open the battery pack.
• If a leak develops, the released electrolytes are corrosive and toxic. DO NOT get the solution in the eyes or on skin, and do not swallow it.
• DO NOT put these batteries in your regular household trash.
• DO NOT incinerate.
• DO NOT put them where they will become part of any waste landfill or municipal solid waste stream.
• Take them to a certified recycling or disposal center.

PROPOSITION 65

WARNING
This product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints;
• Crystalline silica from bricks and cement and other masonry products;
• Arsenic and chromium from chemically treated lumber.

Your risk of exposure to these chemicals varies depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well- ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

INSTALLATION

WARNING
Remove the battery pack from the machine before installation.

WARNING
Do not use accessories that are not recommended for this machine.

UNPACK THE MACHINE
WARNING

• If parts of the machine are damaged, do not use the machine.
• If you do not have all the parts, do not operate the machine.
• If parts are damaged or missing, contact the service center.

1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance with local regulations.

ATTACH THE GUARD

WARNING

Do not touch the cut-off blade.

1. Put the shaft into the groove of the guard.
2. Put the bracket (13) into the slot (14).
3. Align the screw hole on the bracket with the screw hole on the guard.
4. Tighten the screws.

ATTACH THE AUXILIARY HANDLE

1. Loosen the central knob (15).
2. Remove the cap (16) and the lower support (17) .
3. Put the auxiliary handle (4) in the lower support.
4. Put the cap to the lower support.
5. Put the entire block in its housing on the shaft.
6. Set the auxiliary handle in the comfortable position.
7. Lock the auxiliary handle with the central knob.

INSTALL THE BATTERY PACK

WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the motor stops before you install or remove the battery pack.
• Read, know, and do the instructions in the battery and charger manual.

1. Align the lift ribs on the battery pack with the grooves in the battery compartment.
2. Push the battery pack into the battery compartment until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.

REMOVE THE BATTERY PACK

1. Push and hold the battery release button (1).
2. Remove the battery pack from the machine.

OPERATION

IMPORTANT
Before you operate the machine, read and understand the safety regulations and the operation instructions.

WARNING
Be careful when you operate the machine.

CONTROLS

ON/OFF BUTTON
Push this button to connect and disconnect the electrical circuit of the machine.
Green light on (G): the electrical circuit of the machine is on (ON). The machine prepares to operate.
Lights off: the electrical circuit is off (OFF).

IMPORTANT
Do not keep your finger on the button when you move the machine to prevent accidental start.

REVERSE BUTTON

1. If grass winds around the trimmer head or blade, push the reverse button.
2. Start the machine again.

LED INDICATION

1. 4 green lights are on when you start the machine.
2. Push the speed button forward to adjust the speed.

ATTACH THE SHOULDER STRAP

1. Attach the carabiner to the carrying ring on the drive tube.
2. Put on the shoulder strap.
3. Adjust the length of the strap so that the carabiner is about a hand’s width below your right hip.

START THE MACHINE

1. Push the on/off button (6).
2. Push the lock-out button (5) rearward.
3. Pull the trigger (3).

STOP THE MACHINE

1. Release the trigger.
2. Push the on/off button again to turn the machine off.

OPERATION TIPS

WARNING
Keep clearance between the body and the machine.
Do these tips when you use the machine

• Keep the machine connected to the correctly worn harness.
• Keep a firm hold with the two hands on the machine while you operate the machine.
• Cut tall grass from the top down.

If grass winds around the trimmer head:

• Remove the battery pack.
• Remove the grass.

CUTTING TIPS

• Tilt the machine toward the area to be cut. Use the tip of the cutting line to cut grass.
• Move the machine from right to left to prevent thrown debris toward the operator.
• Do not cut in the dangerous area.
• Do not force the trimmer head into uncut grass.
• Wire and picket fences cause cutting line wear and breakage. Stone and brick walls, curbs, and wood can wear the cutting line quickly.

LINE CUT-OFF BLADE
This trimmer is equipped with a line cut-off blade (11) on the guard. The line cut off blade continuously trims the line to ensure a consistent and efficient cut diameter. Advance line whenever you hear the engine running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep line long enough to advance properly.

ADJUST THE LENGTH OF THE CUTTING LINE
While you operate the machine, the cutting line gets worn and shorter. You can adjust the length of the cutting line.

1. Hit the trimmer head against the ground while you operate the machine.
2. Line is automatically released and the cut-off blade cuts the excess length.

MAINTENANCE

IMPORTANT
Read and understand the safety regulations and the maintenance instructions before you clean, repair or do the maintenance work on the machine.

GENERAL INFORMATION
Before the maintenance operations:

• Stop the machine.
• Remove the battery pack.
• Cool the motor.
• Store the machine in cool and dry place.
• Use correct clothing, protective gloves and safety glasses.

CLEAN THE MACHINE

• Clean the machine after use with a moist cloth dipped in neutral detergent.
• Do not use aggressive detergents or solvents to clean the plastic parts or handles.
• Keep the trimmer head free of grass, leaves, or excessive grease.
• Keep the air vents clean and free of debris to avoid overheating and damage to the motor or the battery.
• Do not spray water onto the motor and electrical components.

REMOVE THE REMAINING LINE

1. Push the tabs (19) on the sides of the trimmer head at the same time
2. Pull and remove the spool cover (20).
3. Remove the remaining cutting line.
4. Put the spool cover with spool in the spool housing (23).
5. Push the tabs until the spool cover clicks into position

INSTALL THE CUTTING LINE

1. Remove the remaining cutting line on the spool
2. Line up the slot on the spool cap with the line exist hole on the trimmer head
3. Put the cutting line through the hole. Push the cutting line until it exits the opposite hole.
4. Pull the cutting line through until there is an equal quantity of cutting line on each side.
5. Turn the spool cap clock-wise to wind the cutting line into the trimmer head. Keep approximately 5 in of cutting line above out of each side of the trimmer head.

REMOVE THE TRIMMER HEAD

1. Put the metal rod (E) in the specified angle transmission hole (D) to fix the trimmer head.
2. Remove the spool cover and the spool.
3. Loosen the nut (A) on the trimmer head clockwise with a wrench.
4. Remove the trimmer head.

ASSEMBLE THE TRIMMER HEAD

1. Put the trimmer head onto the housing.
2. Install the nut.
3. Put the metal rod in the specified angle transmission hole to fix the trimmer head.
4. Tighten the nut on the trimmer head counterclockwise with a wrench.

IMPORTANT
You must install the cut-off blade when you use the trimmer head.

TRANSPORTATION AND STORAGE

MOVE THE MACHINE

When you move the machine, you must:

• Wear gloves.
• Stop the machine.
• Remove the battery pack and charge it.
• Assemble the blade guard.

STORE THE MACHINE

• Remove the battery pack from the machine.
• Make sure that children cannot come near the machine.
• Keep the machine away from corrosive agents such as garden chemicals and de-icing salts.
• Secure the machine during transportion to prevent damage or injury. Clean and examine the machine for any damage.

TROUBLESHOOTING

2. Check contact and in- stall the battery pack again.

The battery pack is depleted.| Charge the battery pack.
The lock-out but- ton and trigger are not pushed at the same time.| 1. Pull the lock-out but- ton and hold it.

2. Pull the trigger to start the machine.

(2.4 mm) diameter.
The grass winds around the motor shaft or the trim- mer head.| 1. Stop the machine.

2. Remove the battery pack.

3. Remove the grass from the motor shaft and trim- mer head.

The motor is over- loaded.| 1. Remove the trimmer head from the grass.

2. The motor will recover to work as soon as the load is removed.

3. When you cut, move the trimmer head in and out of the grass to be cut and remove no more than 8″ in pass.

The battery pack or machine is too hot.| 1. Cool the battery pack until its function returns to normal.

2. Cool the machine for approximately 10 mi- nutes.

The battery pack is disconnected from the tool.| Install the battery pack again.
The battery pack is depleted.| Charge the battery pack.
The line does not ad- vance.| Lines are welded to themselves.| Lubricate with silicone spray.
Not enough line on spool.| Install more line.
Lines are worn too short.| Advance the cutting line.
Lines are tangled on spool.| 1. Remove the lines from the spool.

2. Wind the lines.

tip of the line, avoid stones, walls and other hard objects.
| | 2. Advance the cutting line regularly to keep full cutting width.
The grass winds around the trimmer head and motor hous- ing.| Cut tall grass at ground level.| 1. Cut tall grass from the top down.

2. Remove no more than 8″ in each pass to prevent wrapping.

The line does not cut well.| The cut-off blade becomes dull.| Sharpen the cut- off blade with a file or replace it.
Vibration| The line is worn| Make sure that the line on
increases| down at one side| both sides is normal. Ad-
obviously.| and not advanced| vance the line.
| in time.|

TECHNICAL DATA

60BA04/60BA05/60BA06/

60BA08 and other BAC ser- ies

Charger model| 60DP10/606P14 and other CAC series

The recommended ambient temperature range:

LIMITED WARRANTY

Greenworks hereby warranties this product, to the original purchaser with proof of purchase, for a period of four (4) years against defects in materials, parts or workmanship. Greenworks, at its own discretion will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for units which have been used for personal use that have not been hired or rented for industrial/commercial use, and that have been maintained in accordance with the instructions in the owners’ manual supplied with the product from new.

ITEMS NOT COVERED BY WARRANTY:

1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.

HELPLINE:
Warranty service is available by calling our toll-free helpline, at 1-855-345-3934.

TRANSPORTATION CHARGES:
Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by Greenworks.

REPLACEMENT PARTS

No.| Part No.| Qt y| Description| No.| Part No.| Qty| Description
---|---|---|---|---|---|---|---
1| R0202615-00| 1| Trimmer head assembly| 2| R0202614-00| 1| Guard assembly

References

• Greenworks Outdoor Power Equipment, Lawn & Garden Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>