ESTG MT12 Smart Watch User Guide

ESTG MT12 Smart Watch User Guide

Schematic diagram of MT12 watch charging and music download

Thank you for choosing our products, the correct way to charge the MT12 watch is shown in the figure 1.Use the equipped magnetic charger to attach to the metal contacts on the back of the watch. 2.If the USB at the other end is plugged into the computer, you can copy songs.

Note: This watch only supports 5V charging

Adaptation platform requirements

1. Mobile phones above Android 5.0
2. IOS9.0 and above mobile phones
3. Support Bluetooth BT4.0

Preparation before use

Please make sure that the watch is fully charged for the first time. If the watch cannot be turned on due to low battery, please charge the watch first.

Note: The watch needs to be connected to Bluetooth before it can be used. Please activate it according to the operating instructions before using the watch.

How to download and connect the watch

1. Can the QR code or search for “Diri Fit” in the App Store or App Store to download and install the app
   
   App Store
   
   Google Play Icon

2. Connect the watch:

3. Open the APP and click “Bind Watch” to find the MT12 model (Figure 1) and click the connection, as successful as (Figure 2):

** Search connection (Figure 1)

Successful connection (Figure 2)**

3. Enter the mobile phone Bluetooth search page, search and connect to MT12_Audio
   The connection is successful as shown below:

Android

iOS
Note: You can use the watch normally after completing the above operating instructions.

Button function introduction

On/Off: long press the switch button for 3 to 5 seconds to turn on/off

❡Style button: double click to switch style layout

Music button: press the button to enter the music function interface

Note: If you need to use the Bluetooth headset playback mode correctly, please complete the following operations:
Please turn on the headset first and keep the headset device in the search state, and then tap the Bluetooth headset mode to enter the search interface.

ʕ Recording: Long press the key to start fast recording

The presence of this icon indicates that the recording is turned on

Status bar

Note: If the side screen i s turned on, then sliding right to enter the function list will be replaced by the side screen (you can double-click the side button to enter the function list).

Function page

More functions please experience in the watch

Setting method of APP push (Android)

APP settings

1. Open APP-Device-Notifications

2. Click OK

3. Tap Diri Fit to allow notifications

4. Click Allow

Phone settings

1. Phone Settings Notification

2. Click on management notification

3. Management Notification -WeChat

4. Allow notifications

Note: The message push can be viewed by swiping to the right on the main dial interface screen. The above operations are based on WeChat, and the same applies to other similar APP message push operations.

Setting method of APP push (iOS)

APP settings

1. Open APP-device

2. Enter information reminder

Phone settings

1. Phone Settings Notification

2. Click WeChat

3. Allow notification

4. WeChat-me-settings

5. Click message notification

6. Allow notification

Note: The above operations are based on WeChat, and the same applies to other similar APP message push operations

About rebinding the watch or changing the binding of the watch

Android phone settings

1. Settings-Bluetooth

2. Select MT12_Audio

3. Click disconnect

iOS phone settings

1. Settings-Bluetooth

2. Select MT12 and MT12_Audio

3. Click forget this device

Watch settings

About music and recording files

Music file

This machine has built-in memory. If you need to download music, you can connect to the computer through a data cable, open the mobile U disk, and download the downloaded music to the U disk.

Recording files

1. Open the recording interface, slide left to the recording playback interface to play and delete

2. Connect the watch to the computer, open the U disk and enter the “AB_REC” file to find the recording file to play or delete.

FAQ

1. Why can’t you wear watch to take a hot bath?
   The temperature of the bath water is relatively high, will produce a lot of water vapor, which is small molecular radius. It’s easy to infiltrate from the annulus shell gap, when the temperature will fall down and then condense into liquid droplets, easy to cause the loop internal circuit short circuit, damage the watch.

2. Why can’t receive a message push?
   Android phone Settings:

3. Confirm the message push switch is turned on in the mobile phone.

4. All confirmation messages can be displayed normally in the mobile notification banner. The watch message is only pushed by reading the notification banner: if there is no message in the mobile notification banner, the watch will not be able to receive the push.(you need to find the notification setting in the mobile phone Settings, and turn on the notification switch of Whatsapp, facebook, phone, SMS etc.)

iOS phone settings:

1. Confirm the message push switch is turned on in the mobile phone.
2. The confirmation message is that the notification banner can be displayed normally.(you need to find the notification setting in the mobile phone settings and turn on the notification switch of Whatsapp, facebook, Phone, SMS etc.)

Why does the bracelet often disconnect?

Hello, this situation may be caused by the blocking or cleaning of the software by the mobile phone system, which causes the software to not run normally. Please set the mobile phone according to different mobile phone brands. Set the APP lock on the Android phone, as shown in the figure:

FCC Statements

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>