LEIFHEIT 11914 Cordless Vacuum and Wipe Instruction Manual

October 27, 2023
LEIFHEIT

LEIFHEIT LOGO REGULUS AQUA POWERVAC
Akku-Saugwischer
Cordless Vac & WipeLEIFHEIT 11914 Cordless Vacuum and
Wipe

11914 Cordless Vacuum and Wipe

LEIFHEIT 11914 Cordless Vacuum and Wipe - FIGURE 1LEIFHEIT 11914 Cordless Vacuum and Wipe - FIGURE
2LEIFHEIT 11914 Cordless Vacuum and Wipe -
FIGURE 3

**Please read the operating instructions carefully before using this appliance and store these for later reference or for the benefit of subsequent owners.
They will help you to use the device sensibly and correctly from the get go and avoid faulty operation.
Please pay particular attention to the safety instructions provided in this manual. The operating instructions can be found on the Leifheit homepage under
www.leifheit.com**.

Scope of supply

Leifheit cordless Vac & Wipe Operating instructions
Check the contents against the parts list for completeness and for any damage during shipping.
If you discover any shipping damage, do not use the appliance and contact Customer Service immediately.

Product overview

  [1] On / Off button   [16] Vacuum Channel
  [2] Vacuum mode button I/II   [17] Transport wheels
  [3] Water lever   [18] Water outlet nozzles
  [4] Handle   [19] Cleaning roller holder
  [5] Fresh water tank release lever   [20] Cleaning roller
  [6] Fresh water tank   [21] Cleaning roller cover release button
  [7] Dirty water tank   [22] Park station
  [8] Ventilation cover   [23] Fresh water tank cover
  [9] Floor head   [24] Fresh water tank handle
  [10] Operating display   [25] Sponge filter holder
  [11] Dirty water tank release lever   [26] Sponge filter
  [12] Cleaning roller cover   [27] Dirty water tank cover
  [13] Charger adapter   [28] Float
  [14] Charger hollow connector   [29] Dirty water tank handle
  [15] Charge socket   [30] Spilling protection adapter

Technical specifications

Model ………………………Regulus Aqua PowerVac
Rechargeable battery ……………….Li-Ion, 24V 2,5Ah
Operating time ………………….~22 min (Eco-Mode)
Output ……………………………………..120 W
Voltage ……………………………………….24V
Charge time ………………………………….~ 3 h
Fresh water tank volume . . . . . . . . . . . . . . . . . . . . . . . . . .500 ml
Dirty water tank volume ……………………..400 ml
Weight ………………………………………3,3 k
Charge adapter
Model identifier …………………..YLS0241A-E260092
Input voltage …………………….AC 100-240 V.
Input AC frequency ………………….50/60 Hz
Output voltage …………………..DC 26,0 V
Output current …………………..0,92 A
Output power………………………..23,92 W
Average active efficiency ………………….86,57%
Efficiency at low load (10 %) ………..78,86%
No-load power consumption ……….0,09 W
Manufacturer’s name or trade mark, commercial registration number and address
Leifheit AG
Leifheitstraße 1
D-56377 Nassau Germany
Amtsgericht Montabaur
HRB 2857

Intended use

Please note that this product is only intended for household use. Leifheit will not provide any manufacturer’s warranty for commercial use.

  • The appliance serves exclusively vacuum wiping of dry as well as moist vacuum material on water-resistant and sealed floors. These are tiles, PVC, linoleum, laminate and sealed wood.
  • Do not use the application to vacuum flammable fluids, sharp-edged or tipped objects, hot or cold ash and burning cigarettes.
  • The appliance must not be used to vacuum persons or animals.
  • Never cover the air inlet openings or air outlet openings of the appliance switched on. Make sure that these are not clogged by dirt.
  • Use the appliance only with Leifheit approved accessories and spare parts.
  • Always position the appliance at the corresponding park station on a hard and level surface.
  • When charging the appliance, ensure for sufficient distance to heat and moisture sources.
  • Please take care that no tipped objects catch in the cleaning roller or the wheels that could damage the floor.
  • Never operate the appliance without filter.

Any use beyond this is considered as not intended and may lead to damage or injury. The manufacturer shall not be liable for any damages resulting from such use; the user is
solely responsible for damage from improper use.

Safety instructions

Fundamental safety measures must be observes when using an electrical appliance:

  1.  Use the appliance only as described in these instructions.
  2. Never use the appliance if the cable, connector, housing or power supply unit are damaged.
  3. Repairs may only be carried out by authorised customer services technicians. Never open the basic unit singlehandedly. The individual components of the basic unit must not be disassembled, repaired or altered.
  4. The appliance may only be charged using the charger supplied. Make sure that the voltage specified on the rating plate of the power supply unit corresponds with the mains voltage.
  5. Make sure that the appliance as well as the power supply unit do not get wet. Do not operate the appliance or power supply unit with moist or wet hands.
  6. Do not store, charge or use the appliance outdoors or in wet rooms such as bathrooms or similar, but always at room temperature and in a dry location.
  7. Do not use the application in the vicinity of flammable gases.
  8. Protect the appliance against intensive heat and do not expose it to direct sunlight.
  9. This appliance is only suitable for users (also children aged 8 years and above) with limited physical, sensory or physical abilities or with lack of experience or knowledge if they are supervised appro priately or have been instructed in the use of the appliance by a responsible person.
  10. Make sure that children do not play with the appliance.
  11. Do not leave children unattended with the appliance.
  12. Unplug the appliance from the power outlet before cleaning or maintenance.
  13. Do not touch the rotating cleaning roller when the appliance is switched on.
  14. Make sure that the running cleaning roller does not make contact with body parts (e.g. hair, fingers) or items of clothing.
  15. During cleaning, make sure that no body parts (e.g. fingers) are trapped or crushed by the floor head.
  16. Make sure that no objects (e.g. cables, long fringes) catch in the cleaning roller otherwise there is a risk that this or the appliance are damaged.
  17. Store the appliance out of reach of children. Do not leave the appliance unattended when it is switched on.
  18. Keep packaging material such as plastic bags and similar away from children. There is a risk of suffocation.

Operation

The appliance combines vacuuming and wiping in one work step. It is equipped with a 2-tank system with a separate fresh and dirty water tank.
By actuating the water lever, the fresh water is spread over the cleaning roller. This allows the amount of water to be set for every floor type. The rotating cleaning roller removes dust, dry and moist dirt as well as dried stains.
The vacuum function sucks on the cleaning roller and transports the dirt into the dirty water tank. This allows you to always wipe with a clean cleaning roller and fresh water.

Before use

Figure 1
Insert the handle (4) and cable into the appliance until they engage.
CHARGING
During charging, do not clean or maintain the appliance. Fully charge the appliance before the first use and after each use.
Figure 2
Insert the hollow connector of the charger (14) supplied into the charging socket (15) of the appliance. Insert the adapter of the charger (13) in the socket
Figure 3
Operating display (10) flashes green slowly during the charging process.
The appliance is fully charged after 3 hours. Then the operating display illuminates continuously for 2 minutes, then the light goes out.

Application

FILLING THE FRESH WATER TANK
Figure 4
Press release button (5) to remove the fresh water tank (6) on the handle (24).
Open the cover of the fresh water tank (23).
Figure 5
Fill the fresh water tank with max. 60°C hot water.
If required, add non-foaming cleaning agent with low dosage.
CAUTION: Observe the dosing specifications of the cleaning agent. We recommend Leifheit universal cleaner.
Figure 6
Close the tank cover (23) and insert the fresh water tank (6) until you hear it engaging.
CLEANING THE FLOOR
Figure 7
To switch on the appliance, press the On / Off button (1) once. The operating display illuminates green after switching on.
Optional: Press the vacuum mode button (2) once in order to the turbo mode if tiled / stone floors have more stubborn dirt. Then the operating display flashes green slowly. Switch back to Eco mode by pressing the vacuum button again.
Figure 8
Tilt the appliance to the rear to release it from the stand position.
Figure 9
Press the water lever (3) to moisten the cleaning roller (20) as needed
Before starting to clean the floor, keep the water lever pressed for several seconds without moving the appliance in order to quickly and evenly moisten the roller in advance.
To clean the floor, push the appliance back and forth in steady and equal movements.
If the moisture of the cleaning roller reduces, press the water lever again and keep it pressed until the desired moisture is reached again.
The fill level of the dirty water tank (7) must not exceed the maximum fill level.
Figure 10
During cleaning breaks, always place the appliance at the corresponding park station (22) in order to avoid the formation of water stains to the floor from the residual water in the appliance.
Figure 11
Once the dirty water tank (7) is filled to the Max. line, a notification system ( Tank Control Technology) is activated. As a result, the operating display (10) flashes orange and the cleaning roller stops 3 times for a few seconds and then the roller stops completely.
Now the dirty water tank must be emptied at the latest.

Cleaning and maintenance

EMPTY THE DIRTY WATER TANK AND CLEAN THE FILTER
Figure 12
To switch off the appliance, press the On / Off button (1) once again.
Remove the dirty water tank (7).
For this purpose, press the release button (11) down and pull the tank out on handle (30).
Figure 13
Lift the cover (27) from the dirty water tank (7). Empty the dirty water tank.
Figure 14
Remove the sponge filter holder (25) from the cover of the dirty water tank (27).
Remove the sponge filter (26) from the sponge filter holder.
Figure 15
Depending on the degree of soiling, rinse out all parts of the dirty water tank unit (7, 25, 26, 27, 28, 30) under running water.
Figure 16
Before putting back together and insertion of the parts removed, allow all parts to completely dry in the air.
CAUTION: To avoid the formation of odour, remove the dirty water tank unit after use and rinse out. Insert only completely dried parts back in the appliance.
Figure 17
Reassemble the sponge filter (26), sponge filter holder (25), cover (27) and dirty water tank (7).
Figure 18
Reinsert the dirty water tank back into the appliance until you hear it engaging.
REMOVING AND CLEANING THE CLEANING ROLLER
Figure 19
Remove roller cover (12) in order to remove the cleaning roller (20).
To remove the cover, press release button (21) and remove the cover.
Figure 20
Using the roller holder (19), remove the cleaning roller (20) at the edge.
For this purpose, pull the holder upwards out of the guide.
Figure 21
Rinse the cleaning roller (20) and, if necessary, the cleaning roller cover (12) under running water.
Allow the roller to completely dry before using again.
CAUTION: To avoid the formation of odour, remove the cleaning roller after use and rinse out. Insert only the completely dried cleaning roller back in the appliance.
CLEANING THE VACUUM CHANNEL
Figure 22
When the cleaning roller is taken out, remove any soiling on the nozzles (18) and vacuum channel (16) using a moist cloth.
Special Leifheit cleaning brushes for the nozzles, the vacuum channel as well as the water tanks can be purchased in the trade or ordered from our customer services.
INSERTING THE CLEANING ROLLER AND CLOSING THE ROLLER COVER
Figure 23

Make sure that the appliance is switched off and is not charging.
First insert the cleaning roller (20) in the round mount and then insert the roller holder (19) in the guide.
Figure 24
Insert the tabs of the roller cover (12) at the bottom end in the matching mount and close the cover until you hear it engaging
AUTO-WASH PROGRAM
In addition to cleaning your appliance, also use the
AUTO-WASH PROGRAM at regular intervals. When using the program, some vinegar or vinegar cleaner can also be added to the fresh water tank.
Before using the AUTO-WASH PROGRAM, always empty the dirty water tank and put it tank back in. (7).
Figure 25
Fill the fresh water tank (6) with water up to the AUTO-WASH MAX line.
Close the tank cover (23) and insert the fresh water tank until you hear it engaging.
Figure 26
Place the appliance on the corresponding park position (22). Keep the On / Off button (1) pressed together with the Vacuum mode button I/II (2) for 3 seconds and then let go as soon as the appliance starts the AUTO-WASH PROGRAM. Then the operating display flashes green.
Figure 27
After 60 seconds, the program ends and the appliance switches off.
Then remove the dirty water tank (7) and cleaning roller (20) and wash-out.
DISASSEMBLING THE HANDLE
After assembling, do not remove the handle. Disassembly of the handle is only intended if the appliance has to be sent in for service purposes.
Figure 28
Loosen and remove the screw on the rear side of the appliance.
Insert the screwdriver in the opening of the screw hole.
By applying  slightpressure,  the locking mechanism ofthe handle can be released and the handle can be pulled out.

TROUBLESHOOTING

Malfunction Possible cause / Solution
The appliance does not start. The rechargeable battery has not been charged.

Charge the rechargeable battery.
The operating display flashes orange.| The cleaning roller (20) is blocked. Please remove the roller and solve the blockage
The rechargeable battery is empty; recharge the appliance.
The operating display flashes orange and the cleaning roller stops 3 times for a few seconds and then the roller stops completely.| Tank Control Technology: The dirty water tank (7) is full. Please empty the dirty water tank.
The dirty water tank cannot be reinserted in the appliance.| Check if the cover (27) and the sponge filter (25) have been inserted correctly.
The float (28) has been tightened, the appliance has stopped suction, but the Tank Control Technology does not start| The sponge filter (25) is blocked by excessive moisture or dirt particles. Please clean and dry the sponge filter.
The float (28) has been tightened and the appliance has been switched off and on too quickly. Please switch off the appliance for a moment and wait until the float is in the initial position before starting the appliance again.
The Tank Control Technology starts even though the waste water tank (7) is not yet full.| The Tank Control Technology may react inadvertently in the event of jerky movements (e.g. strong bumping against furniture). Please switch off the appliance for a moment and wait until the float (28) is back in its original position before starting the appliance again. Take care not to bump too hard against furniture or other objects.
Malfunction| Possible cause / Solution
---|---
Water is running out of the ventilation cover.| The dirty water (7) tank is full. Please empty the tank.
Little or no water can be added using the water lever.| The fresh water (6) tank is empty. Refill with water.
The nozzles (18) are blocked. Please remove the stuck protection in front of the nozzles. Lime deposits can be carefully removed using a paper clip by inserting it through the openings.
Please use the AUTO-WASH PROGRAM at regular intervals in order to keep the channels and nozzles inside the appliance clean.
Foam remains on the floor.| Please add less cleaning agent or use the Leifheit universal cleaner especially for the Regulus Aqua PowerVac.
The appliance does not absorb water from the floor| The dirty water (7) tank is full. Please empty the tank.
The appliance switches off automatically after approx. 60 seconds.| The AUTO- WASH PROGRAM has been started. Restart the
appliance by briefly pressing the on / off button.
Other faults| Please contact Leifheit Service.

CUSTOMER SERVICES

If you have any questions or suggestions, our Leifheit Service is at your disposal:
Mon – Fri: 08:00 – 17:00 (tall-free)
Service hotline:
00800 537 37 373
(D/F/NL/CZ/E/I/PL)
(liable for costs)
International phone number: 0049 2604 977 0 Internet: www.leifheit.com
IMPORTANT INFORMATION

  • The rechargeable battery must only be charged with the charger provided. The charger should only be used in conjunction with the Leifheit cordless Vac & Wipe.
  • Fully charge the appliance before the first use and again directly after each use.
  • Do not store the appliance after fully discharging the rechargeable battery unused over a period longer than 6 months.

Cleaning the filter

  • Clean the cleaning roller, the sponge filter and other filter parts regularly after use.
  • Allow the cleaning roller and all parts the filter to dry completely before reinserting them back into the cordless Vac & Wipe.

Cleaning the appliance

  • The appliance contains electrical components. Never clean under running water!
  • Clean the appliance with a moist cloth.
  • Do not immerse the appliance in water under any circumstances.

Parking the appliance

  • Only place the appliance on a flat and firm surface underground.
  • To protect sensitive floors against remaining water running out of the appliance, always place the cordless Vac & Wipe on the park station during cleaning breaks and after cleaning.

Use of cleaning agents

  • Where required, use only non-foaming cleaning agent with low dosage.
  • Observe the dosing specifications of the cleaning agent. We recommend Leifheit universal cleaner.

CAUTION
The following instructions must always be observed with lithium-ion batteries: The rechargeable battery must not be damaged or opened; doing so can cause a short circuit. There is risk of fire. Toxic substances hazardous to health can escape. The rechargeable battery must not be put in a fire as well as exposed to direct, strong sun radiation and heat.
WARNING!
NEVER USE THE APPLIANCE IN ONLY PARTIALLY ASSEMBLED CONDITION!

Disposal

The symbol on the product or its packaging indicates that in accordance with Directive 2012/19 EU, this product and the integrated rechargeable battery must not be treated as normal household waste but should be handed over to a collection point for recycling electrical and electronic devices.
You can receive additional information from your municipality, municipal waste disposal company or the shop where you bought the product

Conformity / Declaration of Conformity
Leifheit hereby declares that this appliance is in conformity with the basic requirements of the German Product Safety Act and other applicable provisions and Directives.
he EU Declaration of Conformity can be found under www.leifheit.com.

LEIFHEIT LOGO Sincerely,
The Leifheit Team
Leifheit AG
Leifheitstraße 1
56377 Nassau/Lahn
Deutschland
Quality and Design by Leifheit AG
Leifheitstraße 1
56377 Nassau / Germany
www.leifheit.com

Documents / Resources

| LEIFHEIT 11914 Cordless Vacuum and Wipe [pdf] Instruction Manual
11914 Cordless Vacuum and Wipe, 11914, Cordless Vacuum and Wipe, Cordless Vacuum, Vacuum
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals