Z-EDGE R1 Dual Dash Cam Built-in Wi-Fi FHD 1080P Camera User Guide

R1

USER GUIDE
BEDIENUNGSANLEITUNG

Introduction

Thank you for buying the R1 car dashcam. Protect you and your vehicle with real-time video and audio recording while you’re driving. Please read this manual carefully before using this product. We hope you enjoy using this product.

Features

• Wi-Fi
• 2304x1296P Resolutions (Front Camera Only)
• 7″ LCD Color Screen
• Up to 155-degree wide-angle lens
• Built-in G-Sensor
• Motion Detection
• Parking Mode
• Audio Recording

Package Contents

Product overview

1. Reset Button
2. Power Button
3. TF/Micro SD Card Slot
4. Rear Camera Port (Mini USB)
5. Suction Cup Mount Slot
6. Lens
7. Power/Data Port (Micro USB)
8. Menu Button
9. Up Button
10. Down Button
11. OK Button
12. Speaker
13. Mic
14. Rear Camera
15. Rear View Lens
16. Rear Camera Port (Mini USB)

2 Getting Started

2.1 Inserting the Memory Card

Insert the memory card, with the pins facing towards the back of the device, until it clicks into place.

For reference only front + rear camera recording at 1080P

Remove Memory Card
Push the edge of the memory card inward until you feel it click, then allow it to push out until you can remove it from the slot.

WARNING:

We recommend that you format the memory card in the dash camera directly before use. General Setting >Format SD card. Please note that all data saved on the memory card will be erased after formatting.

Note:

• Supports Micro SDXC cards up to 256GB (Class 10 or above).
• Do not remove or insert the memory card while the device is powered on – this may damage the memory card.

Installation

Please follow the below instructions for mounting your dashcam to the windshield of your vehicle:

Front Camera Installation

1. Slide the car mount into the slot on top of the device until a click sound is heard.

2. Connect the dash camera to the power outlet in your car, (see 2.4)

3. Turn the camera on, whilst looking at the display screen, find a suitable location for installing your dashcam on your windshield.

4. Press the suction cup firmly against your windshield, and rotate the lever clockwise (12 o’clock) to secure.

5. Use the hand tool provided to tuck the power cable into the headliner.

6. In most cases, the power cable can be tucked behind the rubber trim along the A-pillar and doorframe, use the hand tool provided, or gently tug on the rubber trim to remove it to make room for the power cable. The rubber trim can be replaced after using the hand tool. In rare cases, it may be necessary to remove the A-pillar cover.

7. Trace the cable down the side of the doorframe to the floor of the vehicle. Then lift the carpet in the passenger side foot-well and trace the cable beneath this.

8. Alternatively, route the power cable down the doorframe and tuck it behind/ below the glove box. Use the cable clips if required.

9. Bring the cable out by the center console to the lighter/auxiliary power socket.

Rear Camera Installation

1. Connect one end of the Mini USB cable into the Mini USB Port (4) on the dash Connect the other end into the Mini USB Port (16) on the rear camera.

2. Turn the camera on. The rear-lens view automatically appears on the display screen in Dual (PiP) format.
   Tip: To view full-screen, press the ‘Menu’ button (8) to enter the General Settings menu. Use the ‘Up’ and ‘Down’ buttons (9 & 10) to select the Screen Display option and press the ‘OK’ button (11) to confirm. Then select
   Rear Camera using ‘Up’ and ‘Down’ buttons (9 & 10) and confirm with the ‘OK’ button (11).

3. While looking at the display screen and without removing the adhesive backing, find a suitable location for installing your rear-lens camera on your rear

4. Having found a suitable location on your rear windshield, peel off the protective plastic backing from the adhesive mount. Press the adhesive pad firmly against your rear windshield to secure.

5. For a more organized car environment, the rear camera USB cable can be routed as indicated by the dashed line in the diagram. Use the pry tool to tuck the cable behind the car panels or headliner.

Note: Consult your vehicle’s technical manual or consult a professional if you are not sure how to remove interior panels.

WARNING:
Do not install the device on a tinted window – doing so may damage the tint film.

Adjust Device Position

1. Loosen the nut to swivel the device vertically. Click into place and secure by tightening the nut.
2. Swivel the device horizontally for a clear view.

Connecting to Power

Use only the supplied car adapter to power the dashcam and charge the built-in battery.

1. Plug one end of the USB charging cable into the Mini USB port on the dash camera (7).
2. Plug the other end into the car charger, and insert that into your vehicle’s lighter socket

Automatic Power

• Once the vehicle’s engine is switched on, the dashcam automatically powers on.
• When the vehicle engine is switched off, the dashcam automatically saves the recording and power off within 10 seconds.

Manual Power

• To manually turn the power on, press and hold the ‘Power’ Button (2) for up to 3 seconds.
• To manually turn the power off, press, and hold the Power Button (2) for 3

WARNING:

If the environment reaches 115-degrees Fahrenheit or above, the car charger may stop charging the dashcam battery. This is characteristic of a Lithium Polymer battery and is not a malfunction.

 Set Date & Time

Before using the device, we recommend you set the correct date and time:

1. If the device is recording, short press the ‘OK’ button (11) to stop recording, and enter Standby Mode.
2. Press the ‘Menu’ button (8) to enter the General Settings menu.
3. Press the ‘Up’ and ‘Down’ buttons (9 & 10) to select Date/Time and press the ‘OK’ button (11) to confirm.
4. Press the ‘Up’ and ‘Down’ buttons (9 & 10) to adjust the values and then press the ‘OKI button (11) to confirm and move to the next field.
5. With all fields correct, press the ‘OK’ button (11) to save and exit the menu.

WARNING:
Date/Time settings may automatically reset themselves if the battery is allowed to drain completely.

Language

The language can be set from the language menu.

1. Press the ‘Menu’ button (8) to enter the General Settings menu.
2. Use the ‘Up’ and ‘Down’ buttons (9 & 10) to choose the language menu.
3. Press the ’01C button (11) to confirm.
4. Press the ‘Up’ and ‘Down’ buttons (9 & 10) to choose the desired language and then press the ‘OK’ button (11) to confirm the option.
5. The ‘Menu’ button (8) can be used to return from the menu. General Settings > Language >English / Chinese (Simp) / Chinese (Trad) / German /Japanese

 Default Settings

1296P+1080P
Audio Recording| On/Off| On| On| On| On
Loop Reading| 1min,3mins,5mins| 3mins| 3mins| 5miris| 1min
Date Stamp| On/Off| On| On| Off| On
Device Auto Off| Off,l min,3mins,5 mins| 1min| 1min| 3rniris| 1min
G-Sensor| Off, Low, Ncernal, High| Normal| Normal| Low| High
Logo Stamp| On/Off| On| On| On| On
Parking Mode| Ort/Off| Off| On| On| On
Screen Auto Off| Off 1 min,3minsSmins| 3mins| l min| Off| l min
WDR| On/Off| On| On| On| On

There are three preset scenario modes for everyday driving, scenic driving, or when the vehicle is parked. These aim to offer the optimum settings for the best video recording in each of these instances.

You can choose to enable any one of these modes from the settings menu. General Settings > Scenario Mode > Default/ Drive / Scenic / Park

Factory Reset

To reset the dashcam to factory default

Soft Reset

1. If the device is recording, short press the ‘OK’ button (11) to stop recording, and enter Standby Mode.
2. Press the ‘Menu’ button (8) to enter the General Settings menu.
3. Press the and ‘Down’ buttons (9 & 10) to select Restore Factory Settings.
4. Press the OK button (11) to select.
5. Press the and ‘Down’ buttons (9 & 10) to select confirm.
6. Press the OIC button (11) to select

Hard Reset

If the dash camera does not respond, you can force a factory reset using the reset button. To reset the dashcam to the factory default settings, long-press the ‘Reset’ button (1) until the dashcam’s screen turns off.

Using the Car Dash Camera

Recording Videos

With an SD card inserted and the device connected to power, when the car engine is switched on, the dashcam automatically powers on and starts recording. When the vehicle engine is switched off, the dashcam will automatically save the recording and power off within 10 seconds.

Alternatively, short press the ‘ok button (11) to stop/start video recording manually.

Recording Screen

While the dash camera is recording

1. Record
2. Resolution
3. WDR
4. Parking Mode
5. Audio Recording Status
6. Wi-Fi
7. Protect Video
8. Snapshot
9. Audio Recording
10. Stop
11. Date Time
12. Battery

While the dash camera is on standby

1. Pause
2. Resolution
3. WDR
4. Parking Mode
5. Motion Detection
6. Audio Recording Status
7. Wi-Fi
8. Settings
9. Camera
10. Payback
11. Record
12. Date Time
13. Battery

3.3 Adjusting the Settings

Customize the video recording and other general settings via the on-screen display (OSD) menus:

If the device is recording, short press the ‘OK’ button (11) to stop and enter Standby Mode.

1. Press the ‘Menu’ button (8) to enter the General Settings menu.
2. Press the ‘Up’ and ‘Down’ buttons (9 & 10) to select a menu option and press the ‘OK’ button (11) to enter the selected menu.
3. Press the ‘Up’ and ‘Down’ buttons (9 & 10) to select the desired setting and press the ‘OK’ button (11) to confirm the setting.
4. From the General Settings menu, press the ‘Menu’ button (8) to exit the menu.

Adjust the Recording Resolution

The resolutions can be adjusted in the general settings. The R1 dash camera supports 1296P and 1080P front camera recording and 1080P rear camera recording.

The rear camera options will only show when the rear camera is connected to the dash camera.

Front camera only:
General Settings > Resolution > 1296P /1080P

Front and Rear Camera:
General Settings > Resolution > 1296P+1080P /1080P+1080P

Loop Recording

Videos are recorded and saved to the memory card in set intervals. Once the memory card is full, Loop Recording automatically overwrites the earliest unprotected saved file. This prevents long-duration video clips from being lost in a single overwrite. Video files can be saved to the memory card in 1, 3 or 5 minute intervals: General Settings > Loop Recording > 1 min / 3 mins / 5 mins

Emergency Video Protection

If the G-sensor sensitivity is set to low, medium, or high (see and sense an unusual impact or collision the Dash Camera will automatically protect the currently recorded video file from being overwritten. An EMR icon appears top left to signify the current recording is protected and a yellow bar denotes the protected video clip as it records.

To manually protect a video file during a recording, short press the ‘Menu’ button (8).

 Motion Detection

With Motion Detection enabled, video recording is automatically started when movement is detected by the camera lens. After approximately 60 seconds with no movement detected, the video recording is automatically paused.

Enable/disable feature: General Settings > Motion Detection Mode > Motion Detection > On / Off

Note:
Motion detection will only work if the camera is powered omit is different from Poking Mode relies on a G-sensor being activated to trigger it and can be activated when the camera is powered On or Off.

Vibration Detection

The Vibration Detection feature senses unusual impacts or collisions detected by the built-in G-Sensor. It automatically triggers Emergency Video Protection.

Set the sensitivity to automatically trigger these features with smaller or larger vibrations (feature can also be turned Off).
G-sensor sensitive can by adjust from the: General Settings > Sensitivity > Off/ **Low/Middle/ High**

Parking Monitoring

Enable the Parking Mode feature for the dash camera to continue monitoring your vehicle for unusual impact or collision when the engine is turned off and parked. If vibration is detected, the device will automatically turn on and begin recording. Approximately 30 seconds after the motion or vibration is finished, the device will automatically return to monitoring mode. All recordings are automatically protected from being overwritten.

Enable/disable feature: General Settings > Motion Detection Mode > Parking **Mode > On/Off**

Auto Power Off

Enable the Auto Power Off feature for the dash camera to automatically turn off when it is not recording. This can be set to Off, 1 min, 3mins. To disable the auto power-off function set it to off.

General Settings >Auto Power Off > Off/ 1 min / 3 mins.

Screen Auto Off

Enable the Screen Saver feature for the LCD display to automatically power off. This prevents the screen from being a distraction to the driver. This feature can be set to Off, 1 min, 3mins. The screen will automatically power off after the set duration of time. Set the feature to Off for the screen to remain on constantly while the device is powered.

General Settings >Screen Saver > Off / 1 min / 3 mins.

Taking a Snapshot

To take a Snapshot press the up button (9) when the dash camera is powered on and is recording or on standby.

 Audio Recording

When the dash camera is recording the Audio Recording function can enable or disabled by pressing the up button (9).

Playback Videos & Photos

1. If the dash camera is recording, short press the ‘OK’ button (11) to stop and enter Standby Mode.
2. Press the ‘Down’ button (10) to enter Playback Mode.
3. Press the ‘Up’ and ‘Down’ buttons (9 & 10) to select between Normal Video, Emergency Video, or Photo. Press the ‘OK’ button (11) to select or press the ‘Menu’ button (8) to return to standby mode.
4. Press the ‘Up’ and ‘Down’ buttons (9 & 10) to choose the file to preview and the ‘OK’ button (11) to select.
5. Press the ‘Down’ button (10) to preview the file.
6. Press the ‘OK’ button (11) to return/pause the preview.
7. Press the ‘Menu’ button (8) to return to the Playback menu.

Deleting Video & Photo Files

1. Go to the Playlist menu (see 3.14).
2. Navigate to the file you wish to manage and press the ‘OK’ button (11) to select.
3. Press the ‘Up’ button (9) to delete the file.
4. Press the ‘Up’ and ‘Down’ buttons (9 & 10) to select between Yes and No.
5. Use the DIVREC button (11) to confirm your choice.

Enable Wi-Fi

With the Wi-Fi feature enabled the AndroidfiOS app can be used on your supported devices to view video recordings and images.

General Settings > Wi-F > On /Off

Screen Stamps

Enable the logo or date and time stamp to have them appear on your video clips and pictures you can activate them in the menu.
Date and Time Stamp: General Settings > Screen Stamp > Date Stamp > On / Off
Logo Stamp: General Settings > Screen Stamp > Logo Stamp > Off / On

Key Tone

Enable the Key Tone function to have a chime sound when pressing the keys on the dash camera. General Settings > Key Tone > Off / On

Driver Safety Alerts

The dash camera has a Driver Fatigue Alarm and Light Reminder alarms that can be set to aid the driver.
The Driver Fatigue Alarm can be turned off or set to 1, 2 or 4 hours to remind the driver to take a break on longer journeys.
General Settings >Driving Safety > Driver Fatigue Alarm > Off / One hour / Two hours / Four hours
The Light Reminder can be set to remind the driver to turn on the vehicle’s lights. This is calculated from a light sensor built into the camera.
General Settings >Driving Safety > Light Reminder > Off / On

Wi-Fi Setup and App

1.1 Search for the “Z-DashCam” App on the Google Play Store (Android device) / Apple App Store (iOS device). Then download and install on your smart device.

1.2 Alternatively download by scanning the QR code on the dash camera Using a QR code reader on your smart device.

• On the dash camera open the QR code, General settings > APP
• Open the QR code reader on your smart device.
• Scan the QR code displayed on the screen of the dash camera.
• Follow the instructions to download and install the App on your device.

2. Check the Wi-Fi feature is enabled on the R1 dash camera. (See 3.16).

3. Open the Wi-Fi settings on your smart device and select the Z-EDGE R1 Dash Camera. The SSID name is Z-EDGE-R1, followed by 4 characters. g. “Z-EDGERD000C Enter the password when prompted.
   Password: 12345678

4. Open the “Z-Dash Cam” App on your smart device.

5. On the App, click Connect DVR.

Wi-Fi Application Functions

your phone first)
14| Map Full Screen| Toggle the Map view between full and half screen
15| Centre| Center map on dash camera’s location

Menu Overview

General SettingsScreen Stamp

Default/Drive/Scenic/Park
Resolution| Set the resolution of the videos to be recorded.| Front Camera 1296P/1080P Front & Rear Camera 1296P 1080P / 1080P1080P
Loop Recording| Set the duration of each video file recorded to the memory card(see 3.5)| 1Min/3Mins/5Mins
Display Setting| Set how the cameras display on the screen.| Front/8ack/PreviewPIP
WDR| Enable/disable the Wide Dynamic Range(WDR).| Off/On
Sensitivity| Set the G-Sensor sensitivity.| Off/Low/Middle/High
Screen Auto Off| Select time is taken for the display screen to automatically tum of during operation.| Off/lMin/3Mins
Keystone| Enable/disable the sound effect when pressing the buttons.| Off/On
Volume| Set the volume level.| Off/60%/80%/100%
Language| Set the language of the user interface.| English/German/Simplified Chinese/Traditional Chinese
Date/Time| Set the date/time (see 2.5)| YYYY/MM/DD HH:MM
Add/remove a date and time stamp and Logo Stamp. Visible on saved video recordings and photos.| Off/On
Driving Safety| Driver Fatigue Alarm and Light Reminder.| Driver Fatigue Off/One hour/Two hours/Four hours Light Reminder Off/On
Motion Detection Mode| Enable/disable motion detection and parking mode.| Motion Detection/ Parking Mode/Off/On
Power On/ Off Tone| Enable/disable the sound effect when the device powers on/off.| Off/On
WiFi| Enable/disable the will.| Off/On
Auto Power Off| Set an auto power-off delay.| Off/lMin/3Mins
Format SD Card| Format the memory card.

Warning: All content on the memory card will be deleted and CAN NOT be restored or recovered.

| Cancel/Confirm
Format Warming| Set a reminder to format the SD card.| Off/15 days/30 days/ 60 days
Restore Factory Settings| Reset all options to the factory default settings.| Cancel/Confirm
About| Firmware Version.| –

FAQs

Where should I place the dashcam?

• We recommend that you mount the car dashcam as close to the center of the windshield as possible. This should neither distract the driver nor block the driver’s view (see 2.2).

Why does the dashcam stop recording after some time?

• If motion detection is enabled, the dashcam will automatically stop recording when no movements are detected for more than 15 seconds (see 3.7).
• Your micro SD card may be full and need to be formatted before using it again. 1080P HD videos are big in size and G-sensor locked videos cannot be erased We recommend formatting your memory card every 14 days.

Why do you recommend a Class 10 micro SD card or above?

• 1080P HD video has a bigger data flow and hence requires a micro SD card with faster writing speed. If memory cards below Class 10 are used, they may cause the dashcam to freeze or another related video recording/erasing issue.

How do I tum off audio during recording?

• To turn off the Audio Recording, short press the Down button (10) during (Please note: this does not interrupt the video recording).

How long will my battery last after a full charge?

• The dashcam battery usually takes 2-3 hours to fully charge. This can happen simultaneously whilst the dashcam is plugged into your car and The battery can last 5-10 mins on a full charge depending on the model and environmental temperature.

How do I record videos?

• All dash cams are programmed to automatically record when there is power connected and a memory card inserted. When the engine is turned off, or power is disconnected, the dashcam will stop recording approximately after 3-10 secs. Manually start/stop recording by pressing the ‘OK’ button (8).

7 Customer Support

For customer support inquiries please contact support@z-edge.com Or visit our website: www-edge.com

@zeroedgeGA Facebook.conVzeroedgeGA/
@zeroedgeGA twitter.com/zemedgeGA
@zeroedgeGA pinterest.com/zeroedgeGA
@zeroedge youtube.con/zeroedge

Follow us to get the latest updates.

Warranty

Thank you for choosing Z-EDGE. Your satisfaction is always our first priority.
All Z-Edge customers have a 30-day money-back guarantee, to make sure your shopping experience is worry-free.
By default, the unit warranty period is set to 12 months from the unit- shipped date.
You can be corrected to 18 months by registering your product on our official website.

Product Registration URL: www.z-edge.com/pages/register

Product Specifications

Degrees
Still Image (Photo Mode)| Sensor Resolution: 2M
Format: JPEG
ISO| Auto
White Balance| Auto
Microphone| Yes
Speaker| Yes
Interface| Micro USB 2.0
Battery| Built-in Li-polymer rechargeable
(This battery is NOT replaceable)
Operating Temperature| 14° ∼ 158° F
Operating Humidity| 20 ∼ 70% RH
Storage Temperature| -4° ∼ 158° F
Dimensions| 3.5 x 2 x 1.2 inch, 89 x 52 x 32 mm (LxWxH)
Weight| 3.0oz/85g
Car Charger| INPUT: DC 12-24V, OUTPUT: DC 5V lA

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment
3. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

www.z-edge.com
email: support@z-edge.com
R1Z21UMENDE-03

Documents / Resources

| Z-EDGE R1 Dual Dash Cam Built-in Wi-Fi FHD 1080P Camera [pdf] User Guide
22DC01, 2A4R7-22DC01, 2A4R722DC01, R1 Dual Dash Cam Built-in Wi-Fi FHD 1080P Camera, Dual Dash Cam Built-in Wi-Fi FHD 1080P Camera
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>