Z-EDGE Z3D Dash Cam Dual Cameras on a Budget User Guide

: June 5, 2024
: Z-EDGE

Z3D Dash Cam Dual Cameras on a Budget
User Guide

Introduction

Welcome to buy the Z3D car dashcam. Protect you and your vehicle with real- time video and audio recording whilst you’re driving. Featuring a stealth size design and dual-lens for recording front and back. Please read this manual carefully before using this product. We hope you enjoy using this product.

1.1 Features

2560x1440P resolutions · 2.7″ LCD Color screen
Up to 150-degree wide-angle lens
Built-in G-Sensor
Motion Detection
Parking Mode
Audio Recording · GPS

1.2 What’s in the Box

1.3 Product Overview

1 Power Button
2 TF/MicroSD Card Slot
3 ESC/Menu Button
4 Up Button
5 Down Button
6 OK/Record Button
7 Micro USB Port
8 Suction Mount Slot
9 Mini USB Port| 10 Speaker
11 Front-View Lens
12 Mic
13 USB cable
14 Suction Cup Mount
15 USB connector
16 Mini USB Port
17 Rear-View Lens
---|---

Getting Started

2.1 Inserting the Memory Card

Insert the memory card, with the pins facing towards the back of the device, until it clicks into place.
Remove Memory Card
Push the edge of the memory card inward until you feel it click, then allow it to push out until you can remove it from the slot.
WARNING: It is recommended to format the memory card in the dashcam directly in Menu>General Setting>Format SD card before initial use. Please note that all data saved on the memory card will be erased after formatting.
Note:

Supports Micro SDXC cards up to 256GB.
Do not remove or insert the memory card whilst the device is powered on this may damage the memory card.

Storage Capacity

|

Video Recording Time

---|---
16GB| 1.5 Hours
32GB| 3 Hours
64GB| 6 Hours
128GB| 12 Hours
256GB| 24 Hours
For reference only

2.2 Installation

Please follow the below instructions for mounting your dashcam to your vehicle’s windshield:

Slide the car mount into the slot on top of the device until a click sound is heard.
Press the suction cup firmly against your windshield, and rotate the lever clockwise (12 o’clock) to secure. WARNING: Do not install the device on a tinted window – doing so may damage the tint film.

2.3 Adjust Device Position

Loosen the nut to swivel the device vertically. Click into place and secure by tightening the nut.
Swivel the device horizontally for a clear view.

2.4 Powering the Dash Cam

Use only the supplied car charger to power the dashcam and charge the built-in battery.

Plug the USB cable (13) on the car mount into the car dash cam’s USB connector (7).
Plug one end of the USB charging cable into the USB Connector on the car mount (15).
Plug the other end into the car charger, and insert that into your vehicle’s lighter socket.

Automatic Power

Once the vehicle’s engine is switched on, the dashcam will automatically power on.
When the vehicle engine is switched off, the dashcam will automatically save the recording and power off within 10 seconds.

Manual Power

To manually turn the power on, press and hold the ‘Power’ Button (1) for up to 3 seconds.
To manually turn the power off, press and hold the ‘Power’ Button (1) for 3 seconds.

WARNING: If the environment reaches 115-degrees Fahrenheit or above, the car charger may stop charging the dashcam battery. This is characteristic of a Lithium Polymer battery and is not a malfunction.

2.5 Set Date & Time

Before using the device, we recommend you set the correct date and time:

If the device is recording, short press the ‘OK/REC’ button (6) to stop and enter Standby Mode.
Press the ‘Esc/Menu’ button (3) to enter the General Settings menu.
Press the ‘Up’ and ‘Down’ buttons (4 & 5) to select Date/Time and press the ‘OK/REC’ button (6) to confirm.
Press the ‘Up’ and ‘Down’ buttons (4 & 5) to adjust the value and then press ‘OK/REC’ button (6) to confirm and move to the next field.
With all fields correct, press the ‘OK/REC’ button (6) to save and exit the menu.

WARNING: Date/Time settings may automatically reset themselves if the battery is allowed to completely drain. To ensure the correct time you must set the time to your local time zone.

2.6 Default Settings

Resolution	1080P 30,1080P30	Button Beep	ON
Loop Recording	3 mins	Language	English
Motion Detect	OFF	Frequency	60 Hz
Voice Setup	ON	LCD auto Off	3 Minutes
Date Stamp	ON	Auto Power Off	OFF
G-Sensor sensitivity	Normal	Parking monitoring	OFF

2.7 Factory Reset

To reset the dashcam to factory default settings long-press the ‘Power’ button (1) for 7 seconds.

2.8 Rear Camera Installation

Connect one end of the Mini USB cable into the Mini USB Port (9) on the dash camera. Connect the other end into the Mini USB Port (16) on the rear camera.
Turn the camera on. The rear-lens view will automatically appear on the display screen in Dual (PiP) format. Tip: To view full-screen, press the ‘Esc/Menu’ button (3) to enter the General Settings menu. Use the ‘Up’ and ‘Down’ buttons (4 & 5) to select the Screen Display option and press the ‘OK/REC’ button (6) to confirm. Then select Rear Camera using ‘Up’ and ‘Down’ buttons (4 & 5) and confirm with the ‘OK/REC’ button (6).
Whilst looking at the display screen and without removing the adhesive backing, find a suitable location for installing your rear-lens camera on your rear windshield.
Having found a suitable location on your rear windshield, peel off the protective plastic backing from the adhesive mount. Press firmly against your rear windshield to secure.
For a more organized car environment, the rear camera USB cable can be routed as indicated by the dashed line in the diagram.

Using the Car Dash Cam

3.1 Recording Videos

With an SD card inserted and the device connected to power, when the car engine is switched on the dashcam will automatically power on and start recording. When the vehicle engine is switched off, the dashcam will automatically save the recording and power off within 10 seconds. Alternatively, short press the ‘OK/REC’ button (6) to stop/start video recording manually.

3.2 Recording Screen

No.

| Item|

Description

---|---|---
1| Recording| A flashing red light indicates the device is recording with time showing the current duration of the recording.
2| Resolution| Indicates current resolution settings.
3| Loop Recording| Indicates loop recordings length 1, 2 or 3 minutes.
4| GPS| Indicates if the GPS is connected.
5| Motion Detection| Indicates if motion detection on/off.
6| Parking Monitor| Indicates if the parking monitor is on/off.
7| Video Protection| Indicates if video protection is active. Press the’ Esc/Menu’ button (3) to activate when recording.
8| Camera button| Press the ‘Up’ button (4) to enter camera mode.
9| Audio recording| Indicates if the audio recording is active, press the ‘Down’ button (5) to turn on/off when recording.
No.| Item| Description
---|---|---
10| | Indicates if the device is recording, press ‘OK/RFC’
13| Record Stop| button (6) to start/stop recording.
11| Menu| Press the’ Esc/Menu’ button (3) to enter the menu.
12| Preview| Press the’ Down’ button (5) to preview the video/photo.
14| Time Stamp| Time and date

3.3 Adjusting the Settings

Customize the video recording and other general settings via the on-screen display (OSD) menus: If the device is recording, short press the ‘OK/REC’ button (6) to stop and enter Standby Mode.

Press the ‘Esc/Menu’ button (3) to enter the General Settings menu.
Press the ‘Up’ and ‘Down’ buttons (4 & 5) to select a menu option and press the ‘OK/REC’ button (6) to enter the selected menu.
Press the ‘Up’ and ‘Down’ buttons (4 & 5) to select the desired setting and press the ‘OK/REC’ button (6) to confirm the setting.
From the General Settings menu Press the ‘Esc/Menu’ button (3) to enter the Feature Settings menu.
Press the ‘Up’ and ‘Down’ buttons (4 & 5) to select the desired setting and press the ‘OK/REC’ button (6) to confirm the setting.

3.4 Loop Recording

Videos are recorded and saved to the memory card in set intervals. Once the memory card is full, Loop Recording automatically overwrites the earliest unprotected saved file. This prevents long-duration video clips from being lost in a single overwrite. Video files can be saved to the memory card in 1, 2 or 3 mins intervals. General Settings > Loop Recording

3.5 Emergency Video Protection

If Vibration Detection is enabled and senses an unusual impact or collision the dashcam will automatically protect the currently recorded video file from being overwritten. An icon appears top left to signify the current recording is protected.To manually protect a video file during a recording, short press the ‘Esc/Menu’ button (3).

3.6 Motion Detection

With Motion Detection enabled, video recording is automatically started when movement is detected by the camera lens. After approximately 10 seconds with no movement detected, the video recording is automatically paused. Enable/disable feature: Feature Settings > Motion Detect

3.7 Vibration Detection

The Vibration Detection feature senses for unusual impacts or collisions detected by the built-in G-Sensor. It automatically triggers the Emergency Video Protection and Parking Mode features. Set the sensitivity to automatically trigger these features with smaller or larger vibrations (feature can also be turned Off): Feature Settings > G-Sensor Sensitivity

3.8 Parking Monitoring

Enable Parking Monitoring for the dashcam to continue monitoring your vehicle for unusual impact or collision when the engine is turned off and parked. If a vibration is detected, the device will automatically turn on and begin recording. Approximately 20 seconds after the motion or vibration is finished, the device will automatically return to monitoring mode. All recordings are automatically protected from being overwritten. Enable/disable a feature: Feature Settings > Parking Monitoring
Please note: When protection space (30% TF card capacity is full, The protected files will be overwritten with newly recorded protected files

3.9 Taking a Snapshot

If the device is recording, short press the ‘OK/REC’ button (6) to stop and enter Standby Mode.
Short press the ‘Up’ button (4) to enter Photo Mode. 3. Press the ‘Up’ button (4) to take a snapshot.

3.10 Playback Videos & Photos

If the device is recording, short press the ‘OK/REC’ button (6) to stop and enter Standby Mode.
Press the ‘Down’ button (5) to enter Playback Mode.
Press the ‘Up’ and ‘Down’ buttons (4 & 5) to select between Normal Video, Emergency Video or Photo. Press the ‘OK/REC’ button (6) to select or press the ‘ESC/Menu’ button (3) to return to standby mode.
Press the ‘Up’ and ‘Down’ buttons (4 & 5) to choose the file to preview and the ‘OK/REC’ button (6) to select.
Press the ‘OK/REC’ button (6) to preview the file. 6. Press the ‘ESC/Menu’ button (3) to return to the playlist menu.

3.11 Managing Video & Photo Files

Go to the Playlist menu (see 3.10).
Navigate to the file you wish to manage and press the ‘OK/REC’ button (6) to select.
Press the ‘Up’ button (4) to delete the file.
Press the ‘Up’ and ‘Down’ buttons (4 & 5) to select between Yes and No.
Use the ‘OK/REC’ button (6) to confirm your choice.

WARNING: Deleted files cannot be recovered. Please ensure you backup important files before deleting them.

3.12 GPS

Integrated into the car mount suction cup is a GPS receiver that can pinpoint the location of your car dash cam anywhere on Earth. Video recordings include GPS tracking data that records location, speed, time, and other variables that can be viewed on a GPS Multimedia Player.

Ensure the car mount USB cable is plugged into the car dash cams’ USB connector to enable GPS tracking.
Go to http://zeroedgetechnology.com/downloads/ to download the compatible GPS Multimedia Player.
Install GPS Multimedia Player on your laptop or computer.
Run the program and click ‘Open File’ to search and playback a video recording.

Note:

GPS Multimedia Player is compatible with Microsoft Windows and Apple Mac.
GPS tracking data may not be viewable using other GPS Players.
Car dashcam videos can be played from the SD card or from the car dashcam when connected to a computer via the USB port.

Menu	Feature	Description	Available option
General Settings	Resolution	Set the resolution of the videos to be
recorded.	Front camera and rear camera connected:

1080P30, 1080P30
Front camera only: 2560x1440P 30 fps 2304x1296P 30 fps
1920x1080P 60 fps
1920x1080P 30 fps
1280x720P 120 fps
1280x720P 60 fps
1280x720P 30 fps
Screen Display| Sets the screen display| Front Camera, Rear Camera, PIP
Loop Recording| Set the duration of each video file recorded to the
memory card (see 3.4).| 1 min / 2 mins / 3 mins
General Settings|
---|---
Voice Setup| Enable/disable audio recording.| On / Off
Exposure| Set the dash cam exposure| +2.0, +5/3, +4/3, +1.0,
+2/3, +1/3, +0.0, -1/3.
-2/3, -1.0, -4/3, -5/3, -2.0
Stamp Setup| Add/remove a date and time stamp, Driver ID, and Logo stamp visible on saved video recordings.| Date Stamp On / Off, Driver ID Setting On / Off, Logo Stamp On Off
Language| Set dashcam language| English, French, German, Portuguese, Spanish, Italian
Time Setup| Set the date/time (see 2.5).| YYYY / DD / MM / GMT HH : MM : SS
Driver ID Setting| Input Driver ID setting|
Button Beep| Enable/Disable Key Tone| On / Off

Menu

| Feature| Description|

Available option

---|---|---|---
General Settings| Auto Power Off| Set the duration for Auto Power Off| 1 min / 3 mins / 5 mins / Off
LCD Auto Off| Set the duration for LCD Auto Off| 1 min / 3 mins / Off
WDR| Enable/Disable Wide Dynamic Range| On / Off
Frequency| Change frequency| 50Hz / 60Hz
Format| Format the micro SD card| OK / Return
Default| Restore the car dashcam to default settings| OK / Return
Version Info| Displays firmware version|
Feature Settings| Driver fatigue alarm| Set the fatigue alarm| 1 Hour, 2 Hours, 4 Hours, Off
Remind lights| Enable/Disable remind the light| On / Off
Motion Detect| Enable/Disable the motion detection feature| On / Off
Parking Monitoring| Enable/Disable to protect your vehicle from hit-and-run incidents when the engine is off (see 3.8).| On/Off
G-Sensor Sensitivity| Adjust the light G-Sensor Sensitivity| Off / High / Normal / Low

FAQs

Where should I place the dashcam?
· We recommend that you mount the car dashcam as close to the center of the windshield as possible. This should neither distract the driver nor block the drivers view (see 2.4).
Why does the dashcam stop recording after some time?

If motion detection is enabled, the dashcam will automatically stop recording when no movements is detected for more than 15 seconds (see 3.6).
Your micro SD card may be full and need to be formatted before using it again. 1080P HD videos are big in size and G-sensor locked videos cannot be erased automatically. We recommend formatting your memory card every 14 days.

Why do you recommend a Class 10 micro SD card or above?

1080P HD video has a bigger data flow and hence requires a micro SD card with faster writing speed. If memory cards below Class 10 are used, they may cause the dashcam to freeze or another related video recording/erasing issue.

How do I turn off audio during recording?

To turn off the Audio Recording, short press the ‘Down’ button (5) during recording. (Please note: this does not interrupt the video recording).

How long will my battery last after a full charge?

The dashcam battery usually takes 2-3 hours to fully charge. This can happen simultaneously whilst the dashcam is plugged into your car and recording. The battery can last 15 mins on a full charge depending on the model and environmental temperature.

How do I record videos?

All dash cams are programmed to automatically record when there is power connected and a memory card inserted. When the engine is turned off, or power is disconnected, the dashcam will stop recording approximately after 3-10 secs. Manually start/stop recording by pressing the ‘OK/Rec’ button (6).

Customer Support

For customer support inquiries please contact: support@zeroedgetechnology.com Or visit our website: www.z-edge.com

Warranty

All Zero Edge customers have a 30-day money-back guarantee, to make sure your shopping experience is worry-free. You also get a 12-month warranty; if you subscribe to our official website (www.zeroedgetechnology.com/) you can extend the warranty to 18 months.http://eepurl.com/bSMiP1
You will receive notifications and introductions about our new products before they are released to the market. Additionally, you could be selected to enjoy a special discount or coupon if purchasing our products for detailed evaluation.
Your opinion matters
Z-Edge is committed to improving our products to bring you the best user experience. We value your feedback and encourage you to share your experience with other shoppers.
You can also send us your thoughts and feedback on social media and follow us on Facebook (www.facebook.com/zeroedgeGA/) & YouTube to get the latest news, reviews, discounts, and giveaways.
Thank you for choosing Z-Edge!

Product Specifications

Item

|

Description

---|---
Image Sensor| CMOS sensor
Effective Pixels| 2560x1440P
Storage Media| Supports Micro SDXC, up to 256GB
LCD Display| 2.7” LCD color TFT
Lens| Wide Angle Fixed Focus lens F2.0
Focus Range| 1.5m~Infinity
Movie Clip| Resolution: Front camera and rear camera connected:
1920x1080P 30fps + 1920x1080P 30fps
Front camera only: 2560x1440P 30fps
2304x1296P 30fps
1920x1080P 60fps
1920x1080P 30fps
1280x720P 120fps
1280x720P 60fps
1280x720P 30fps
MP4
Still Image (Photo Mode)| Sensor Resolution: 4032×3024 (12M)
JPEG
G-Sensor| Yes
Microphone| Yes
Speaker| Yes
Interface| Micro USB x1, Mini USB x1
Battery| Internal Li-ion battery rechargeable (This battery is NOT replaceable)

Item

|

Description

---|---
Operating Temperature| -10 to 60°C / 14 to 140°F
Storage Temperature| -20 to 70°C / -4 to 158°F
Dimensions| Front camera: 3.82 inch x 1.97 inch x 1.28 inch (97mm x 50mm x 32.5mm)(LxWxH)
Rear camera:2.1 inch x 1.6 inch x 1.3 inch (54.5 mm x 40mm x 32mm)(LxWxH)
Weight| Front camera: 3.0oz/85g
Rear camera: 1.4oz / 40g
Car Charger| INPUT: DC 12-24V, OUTPUT: DC 5V 2.4A
GPS Logger| Built-in

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.