MESHTEK MTMR1650W LED Lamp User Manual
- June 6, 2024
- MESHTEK
Table of Contents
User Manual
MTMR1650W User Manual
Revision 1.0
Introduction
The MeshTek® MR16 is an RGBW SmartBulb. Turn On/off, Change color, mix colors, change brightness remotely through any Smart device using our iOS and Android app over Bluetooth Low Energy (BLE) protocol.
Features
- Bluetooth enabled, RGBW Bulb
- Control colors from your Smart device
- Dimmable via App (not suitable for use with external dimmers)
- Download MeshTek® app to change Bulb settings
- Android and iOS compatible
Application
- Spotlight
- Landscape Lighting
Electrical Parameters
- Input Voltage: 12VAC / 12VDC
- Wattage: 5.5W
- Lumens: 500lm @ 4000K
- Beam Angle: 40°
- Kelvin Temperature: 2300-8000K
- Color: RGBW
- CRI: 70
- IP Rating: IP64
- Operating Temperature: 0° to 25°
Block Diagram
Installation Method
The basic installation method is the same as that of a standard halogen MR16.
Turn off the main power switch of the installation place prior to connection.
Before installing the product, the lamp that was being used must be turned
off. Replace it once it has sufficiently cooled.
- Check to see if the socket at the installation location is of the GU5.3 standard.
- Insert the MR16 SmartBulb perpendicularly into the socket and make sure that pins are fully inserted so that they aren’t visible. (Be cautious: The socket or product may get damaged if excessive force is applied while handling or plugging in / out the MR16 SmartBulb)
- Turn the power switch on to see if the product is functioning correctly.
- Follow the setup process and pair the MR16 SmartBulb with the MeshTek® app to turn on/off, change color, dim the brightness, etc.
REGULATORY APPROVAL
a. FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation if this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
FCC CAUTION: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user‘s authority to operate
the equipment
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Important Note: FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
b. IC compliance
This device complies with Innovation, Science, and Economic Development Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Under Innovation, Science and Economic Development Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Innovation, Science and Economic Development Canada. To reduce potential radio interference to other users, the antenna type and its gain should be chosen in such a way that the equivalent isotropically radiated power (e.i.r.p.) is not more than that is necessary for successful communication.
Important Note: IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20
cm between the radiator and your body.
© MeshTek Labs
www.meshtek.com
Confidential
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>