Shenzhen Lococo Technology ALU1 UHF Wireless Recording Microphone Instruction Manual

Shenzhen Lococo Technology ALU1 UHF Wireless Recording Microphone

Instruction for use

• Mini stylish“ exterior design
• Long-range wireless transmission
• Real-time monitoring recording
• High definition call& recording

Thank you for choosing to use our wireless microphone products!
This device is a multi-purpose UHF wireless transmitter (low power consumption, long distance). It con be used with UHF receiver and USB-Type-c converter for wireless recording of mobile phones and computers.

• Mini st,1ish exterior design
• Long-distance ‘Wireless transmission, strong anti-interference
• High-sensitivity microphone core and professional wireless solution
• Clear wireless recording. with real-time monitoring function
• Built-in high-capacity pOlymer battery for longer time
• High-brightness led display. more intuitive working state

PRECAUTIONS AND WARM TIPS

1. The Lavalier microphone is clamped in the collar mouth, about 5-10cm away from the mouth is more appropriate, and then the volume is adjusted to the appropriate size ( 11 levels of volume con be adjusted).

2. If you need to reploce the battery, you must use the same specification (same type or equivalent type) battery before replacing, otherwise it moy leod lo the machine is not available. The works abnormally or is damaged. If the battery is not replaced properly, there will be an explosion risk! (For battery specifications, please refer to
   the technical parameters of the 5th product]

3. in the use of external power adopter. please choose to obtain CCC certification and meet the standard requirements of the adapter [DC 5V=l A).

4. Under normal circumstances, 1he products have been paired when leaving the factory, and con be used normally when unpacked without frequency alignment. If you need to adjust the frequency, please press the 4th: product Use lhe method lo operate.

5. The product is standard equipped wilh USB lo Type-c converter. Please follow the connection instructions, read lhe plug label, and select the correct connection for the device Port insertion to avoid problems when using.

PR0DUCT FUNCTION INTRODUCTION

1. The transmitter antenna
2. Charging interface(DC 5V:::)
3. Electric quantity indicator
4. Microphone
5. Power switch (long press On/Off)
6. NC” button (long press 1 o seconds to pair; Short press to change the  frequency)
7. Volume +
8. Volume-
9. Indicator light [ working blue light on, charging red Ught)

Figure 2: Receiver

1. Receiver content
2. 3.5mm headphone monitoring port
3. Electric quantity indicator light
4. Pick-up indicator(Green light}
5. USB plugs

HOW TO CONNECT & USE

1. Connect computer
   After the receiver is plugged into the USB port on the computer, you need to set ALU l as the default microphone input device in the computer audio settings. If the computer uses other third-party audio software to collect microphone signals, set ALU1 as the default microphone input device as well. The computer system or audio software will receive digital audio simultaneously, and the 3.5 jack: of the receiver can monitor at the same time.

2. .Connect Android device
   The receiver is connected to mobile devices such as phones or tablets via o converter for recording or live streaming.

Note:
On Android phones made before 2019, The built-in Android camera opp doesn’t support an external microphone. Third-party video APP software must be used to shoot, Such as Open Camera, Xioaying, Douyin, Kuaishou and other software can solve this problem There are no such restrictions for live streaming and recording.
Most Android phones released after 2019 (Android 10.0 or higher) don’t have these restrictions. There are no such restrictions on iPhones.

HOW TO USE THE PRODUCT

1. The connection between transmitter and receiver
   Long press Transmitter on the right side of the power button for 2 seconds boot, hold down the right side of the” C” lcey about 10 seconds, when the work: blue lights flashing fast release. Plug the receiver into the device and turn it on. can enter the wireless counter part. wait a few seconds later, transmilters: and receivers of blue ltghts stop flashing, said transmitters and receivers pairing is successful, can be used.

2. Frequency or Volume adjustment
   The default volume of the transmitter is level 8 when it starts
   up. At this time. press the right”-” button to reduce the volume. or press the right”+” button to increase the volume. Each time press button to reduce or increase the volume by 1 level, o total of 0-11 levels can be adjusted.
   Press the “C” button lo adjust the frequency. Each lime press button to the frequency is increased by 1 MHz, 552.5MHz-586.5MHz cycle, a total of 15 frequency points can be adjusted.

3. Multiple devices used at the same time
   When multiple devices are used at the same time, You must follow the above steps I .(the connection method between the transmitter and the connector) to reconnect once, And then adjust the frequency according to Step2. If 1 O devices are used at the some time, the frequency must be adjusted in sequence, And there can be no repetition between the 10 frequency points.
   This product can support 15 units at the same time no crosstollc frequency. no interference!
   Note: Dual emitters only support 2 frequency points.

4. Battery power display:
   The three blue lights” … ” on the side of the product are electric quantity indicator lights , 3 lights represen1 100% electric quantity;
   2 lights represent 7.5% electric quantity;l light represents 50% electric quantity; When 3 lights” … ” of product keep flashing represents thon 25%, please turn ii off and charge if in time.

5. Battery Charging Tips:
   use the DC sv I A output charger to charge the product In the shutdown state. At this time, the red light is atways on. After
   2-3 hours of charging, the red light goes off, indicating that the battery has been fully charged. Please unplug the charging cable.

6. Factory reset settings
   In the shutdown state, press the”-t” button of the transmitter, and then press the power button to start up. At this time, the blue Ughf of the working indicator of the transmitter flashes quickly. Immediately plug the receiver into the device to start up, and the orange light of the working Indicator of the receiver flashes. After several seconds, both the transmitter ord receiver indicators stop flashing, indicating that the factory reset is successful.

PRODUCT TECHNICAL PARAMETERS

ACCESSORIES LIST

Warranty Card

1. The producf5 provided by the company, non-human damage, the implementation of a one-year warranty, after-sale within a month due to product quality problems, unconditional and timely replacement.
2.  After the warranty period, the company will follow up from time to time, free of charge to assist in daily maintenance, responsible for lifelong maintenance, depending on the cost of materials.
3. For quality or maintenance sues, please contact the local distributors.
4. The following circumstances do not enjoy warranty services:
   a: artificial damage caused by failure to use, maintain and keep the product is not in accordance with the instructions for use
   b: damage caused by the dismantling of the machine by technicians not related to the company.
   c. damage caused by force more.

Note: Due to the continuous optimization of products, parameters may change without notice, the actual packaging of the product shall prevail, the right of interpretation belongs to the company

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>