FD K911T Wireless Keyboard User Manual

FD K911T Wireless Keyboard

Packing List

Basic Specification

• Keyboard size: 310.6×142.3×23.6mm
• Keyboard net weight: 781.0g±10.0g
• System support:
• 2.4G or BT3.0 mode:
  • Windows XP
  • Windows7
  • Windows8.1
  • Windows10
  • Mac OS X10.4 or above
• BT5.0 mode:
  • Win8.1
  • Win10
  • Mac OS X10.4 or above

Instructions

Initial Use

1. Place 2 AAA dry batteries into the keyboard with the correct polarity. Turn on the switch on the upper right corner of the keyboard, and it is in the factory default 2.4G mode.
2. Take out the receiver of the battery compartment and plug it into the USB port of the computer. Wait for the computer to install the driver automatically, and you can use the product after that

McdeSWitch

BTl Mede

1. Short press BTl mode switch button and its indicator will flash slowly showing that the keyboard is in BTl mode.
2. Long press BTl mode switch button for 3s and its indicator will flash quickly showing that the keyboard enters pairing state.
   Turn on the Bluetooth of your laptop, if your computer system is Win 7 or earlier. please select to connect “BT3.0 KB”. If your computer system is Win 8 or later. please select to connect “BTS.O KB”.

BT2Mcde
Refer to BTl connection instructions.

Diagram

1. Multi-mode Switch. The product supports and connects.
   It can be connected with and control 3 devices. User can switch modes via the corresponding mode switch button to control the corresponding device.

2. Integrated Holder. The top integrated holder can hold phones, tablets, or other mobile devices easily. It can maintain an appropriate angle to make you easy to read when typing.

3. Switch between F Keys and Multimedia Keys

press FN+ ESC simultaneously to switch between the default function and FN combined function, and press again to restore.

The solution to Keyboard’s 2.4G mode connection issue

1. Turn on the power switch and switch the keyboard to 2.4G mode.
2. Press Esc and (I) button for 3-5 seconds and release until the indicator of2.4G mode flashes.
3. Plug the receiver into the computer. It is successfully connected when the indicator of 2.4G mode stops flashing. It can work then.

The solution to keyboard’s BTl mode connection issue

1. Clear the Bluetooth connection list of the computer.
2. Turn on the power switch and switch it to BTl mode.
3. Long press the button of BTl mode for over 3s and release until its indicator light flashes
4. Turn on the Bluetooth of computer. If your computer system is Win 7 or earlier, please select to connect “BT3.0 KB”. If your computer system is Win 8 or later, please select to connect “BTS.O KB·.
   The keyboard”s BTl mode can work after a successful connection.

BT2 Mode
Refer to BTl mode solutions.
Note
If the product is still unworkable after above solutions. you could repeat those steps for a few times. If your problem can’t get solved yet. please contact our Customer Service for help

FCC Statment

1. This device complies with Part 15 of the FCC Rules.
   Operation is subject to the following two conditions:

2. This device may not cause harmful interference, and

3. This device must accept any interference received, including interference that may cause undesired operation.

4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>