Aurora HJ-XKD09 Star Projector User Guide
- June 6, 2024
- Aurora
Table of Contents
Manual of Aurora Star Projector
HJ-XKDO9
Open Box to Check:
The manual contains important safety recommendations and operating
instructions. Please follow the manual to avoid “damage” or “not working” due
to improper operation. Please check whether the product is broken when you
receive the product.
Attention:
Please power off the light projector after 2-3 hours to cool down for several
minutes then start using it again to get a longer lifetime.
Accessories
Buttons
① Power Button: After power on, by using the power button, you can turn on/off
the projector.
② Star/Northern Lights Control Button: Through this button, you can choose the
model you like
- Stars + Northern Lights
- Stars only
- Northern Lights only
③ Short press to select the previous song/ Long press to decrease the volume.
④ Short press to select the next song/Long press to increase the volume.
Buttons of remote control
| 1 | **** | Power ON/OFF |
|---|---|---|
| 2 | Northern Lights ON/OFF | |
| 3 | Laser ON/OFF | |
| 4 |
| Volume +/- | White-noise and your personal music can be controlled.
5| | Previous/Next Song |Your personal music and the white noise
6| | play pause button
7|
R
| Red Aurora Light| By using these buttons, you can choose different solid
colors or mixed colors as you like. Solid colors: Red, Blue, Green, White.
Mixed colors:
1. Red + Blue + Green 2. Red + Blue + White 3. Red + Green + White 4. Blue +
Green + White 5. Red Blue 6. Red + Green 7. Red + White 8. Blue + Green 9.
Blue + White 10. Green + White.
8|
G
| Green Aurora Light
9|
B
| Blue Aurora Light
10|
W
| White Aurora Light
11| | Brightness +/-
12| | Aurora light speed +/-
13| | Sleep timers 1/2 hours
14| | Switch between different modes
15| | Sound activated flicker mode (Lights-play sync on music or voice beats,
Bluetooth must be connected.)
16| | White Noise & Bluetooth Speaker ON/OFF (8 soothing sounds: 1. Soft light
music 2. Early morning jungle 3. Ocean waves 4. Summer night 5. Rain
6. Music box 7. Stream 8. Bonfire)
Tips:
When your music is playing under the Bluetooth connected state, press the
“Bluetooth music”(16) button, you can switch the Bluetooth music mode to the
white noise mode(8 sounds), then Bluetooth music is paused. Press again to
turn off the natural sounds, the Bluetooth music mode is on, then you need to
switch your music to theplayback state.
Laser parameters
Just need to point the remote at any part of the projector, the projector can be controlled.
Single-point laser power: less than 0.4 mW
LED light source: 1*4W| Power consumption: 7-10W
Power input: 100-240V AC 50-60HZ USB DC5V / 2000mA
Working temperature: 4°F – 113°F (-20°C – 45°C)
Projection area: 215-861 square feet (20-80 m2)
(Laser is harmful to eyes. Do not look at it directly.)
Statement:
- With the new technology” star lights blinking “(The green stars will not stay still all the time, it will flicker for a while and then disappear for a while, without any regularity), which is designed to reduce or even eliminate the impact of laser to eyes.
- It has a 4-hour automatic shutdown function (except the timer function), and it will automatically shut down after 4 hours of continuous operation.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be u sed in portable exposure condition without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>