in sink erator 76006 Evolution Septic Assist 3-4 HP Household Garbage Disposal Installation Guide

in sink erator 76006 Evolution Septic Assist 3-4 HP Household Garbage

Disposal

• DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
• WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
• CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE is used to address practices not related to personal injury.

SAFETY INSTRUCTIONS
Safety Instructions or equivalent signs indicate specific safety-related instructions or procedures.

Garbage Disposal includes

Tools and Materials

Dimensions

Before You Begin

WARNING
Read these instructions carefully. Failure to follow the Installation, Operating and User-Maintenance Instructions may result in personal injury or property damage.

Removal of old disposer

WARNING
SHOCK HAZARD
Turn off electric power at circuit breaker or fuse box.

1. If you are replacing an existing disposer, continue to Step 2. If there is no existing disposer, disconnect sink drain and skip to Step 9.
2. Turn off electrical power at circuit breaker or fuse box. Disconnect drain trap from waste discharge tube. Disconnect dishwasher if connected to the disposer.
3. Support disposer, insert end of wrenchette (J) into right side of mounting lug, and turn. Disposer will fall free.
4. Flip disposer over and remove electrical cover plate. Save cable connector if applicable
5. Disconnect the disposer wires from the electrical supply.

Remove existing disposer

Is the new disposer mounting the same as the old one? If YES, you may choose to skip to step 15. If NO, continue to step 7.

1. Note: For sinks thicker than 3/8”, you will need to replace existing 1-1/2” screws with 1-1/8” screws (G2). See step 14.
2. Using a flathead screwdriver, loosen the 3 screws on the mounting assembly.
3. Using a flathead screwdriver, pry off snap ring (H).

Install flange in sink hole

1. Remove flange from sink. Remove old plumber’s putty from sink with putty knife.
2. Evenly apply 1/2” thick rope of plumber’s putty around sink flange (C).
3. Press flange (C) firmly into sink drain. Re-move excess putty.

NOTICE
Property Damage: Risk of long/short term water leakage if not properly assembled.

Attach upper mounting assembly

1. Place a weight, such as the disposer, on the sink flange to hold it in place. Use a towel to avoid scratching sink.
2. Insert fiber gasket (D), backup flange (E) and mounting ring (F). Hold in place while inserting snap ring (H). Pull snap ring (H) open and press firmly until it snaps into place.
3. Tighten 1-1/2” screws (G1) evenly and firmly against backup flange. Use shorter 1-1/8” screws (G2) if sink is more than 3/8” thick.

IMPORTANT: Dishwasher connection only STOP! If connecting a dishwasher, remove drain plug in step 15.
If NOT connecting a dishwasher, con-tinue to step 16.

Turn disposer (I) onto side and knock out drain plug with screwdriver. Remove plug from inside of dis-poser with pliers.

NOTICE
If the dishwasher connection is made without removing the plug, the dishwasher may overflow.

Connect disposer to electrical supply

1. Turn disposer over and remove electrical cover plate. Pull out wires.
2. Insert cable connector (not included) and run electrical cable through access hole on bottom of disposer. Tighten cable connector.
3. This disposer requires a switch with a marked “Off” position (wired to disconnect all ungrounded supply conductors) installed within sight of the disposer sink opening (1 hp minimum rating).
4. Connect white wire from disposer to neutral (white) wire from power source. Connect black wire from disposer to hot (black, red) wire from power source with wire nuts (not included). Connect ground wire to green grounding screw. Unit must be grounded for safe and proper installation.

WARNING
Improper grounding can result in electric shock hazard.

1. Push wires into disposer and replace electrical cover plate.
2. You may need to trim discharge tube (L or M) to ensure proper fit.
3. Place tube (L or M) into Anti-Vibration Tailpipe Mount™. Use provided tubes for best results. Secure with spring load hose clamp (K) (provided).

NOTICE
Failure to use the spring load hose clamp provided voids warranty.

Connect disposer to the mounting assembly

Hang disposer by aligning 3 mounting tabs with slide-up ramps on mounting ring.

WARNING
Do not position your head or body under disposer; unit could fall during removal or installation.

NOTICE
Property Damage: Risk of long/short term water leakage if all three mounting tabs are not properly engaged on all slide-up ramps and locked in place past the ridges.

1. Turn mounting ring until all 3 mounting tabs lock over the ridges on the slide-up ramps
2. Detach removable portion of spec label and place on a visible location.
3. Reconnect plumbing (and dishwasher connection if used).

CAUTION
To avoid leaks and/or potential falling hazard, make sure all three mounting tabs are locked over ridges.

NOTICE
Property Damage: Risk of long/short term water leakage if not properly assembled.
Make sure Anti-Vibration Tailpipe Mount™ is not flexed. You may need to trim tube for proper fit. To reduce the potential of leaking, the drain line must be properly pitched (not less than 1/4” of pitch per foot of run) from the disposer to the drain connection, with the drain connection being lower than the disposer discharge. Failure to do so could lead to premature corrosion or leaking due to standing water left in the disposer.

Insert stopper (A) into sink opening. Fill sink with water, then test for leaks. Reconnect electrical power at fuse box or circuit breaker box.

INSTALLING AND REPLACING THE BIO-CHARGE® BOTTLE

Installing Bio-Charge® Bottle
Use only InSinkErator® Bio-Charge® septic assist bottles. Do not squeeze the Bio-Charge® Bottle; squeezing the bottle may cause Bio-Charge® to discharge and spill.

• Unscrew Bio-Charge® dispenser cap nozzle counterclockwise until nozzle pops upward to dispensing position. Do not remove dispenser cap nozzle.
• Align bottle with concave side toward disposer. IMPORTANT: Press septic assist bottle firmly into place. The bottle MUST be seated into the dispose housing for proper operation; there SHOULD NOT be a gap. (When installed correctly, the button on the disposer housing will be fully ejected.
• Release button. Pull bottle down slightly to ensure it is engaged.

Replacing Bio-Charge® Bottle
To keep your septic system operating at peak efficiency, replace the Bio- Charge® bottle when it is empty.

• Make sure disposer is off.
• Press button on disposer just above bottle and pull bottle down to remove it. (Do not refill or reuse empty bottle.)

INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, INJURY TO PERSONS OR DAMAGE TO PROPERTY

WARNING
Personal Injury: Do not position your head or body under disposer; unit could fall during removal or installation.

GROUNDING INSTRUCTIONS

For all grounded, cord-connected disposers:
This disposer must be grounded to reduce the risk of electric shock in the event of a malfunction or breakdown. Grounding provides a path of least r esistance for electric current. If your disposer did not include a factory- installed power cord, use a cord having an equipment-grounding conductor and a grounding plug. (InSinkErator power cord accessory CRD-00 recommended.) The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

For permanently connected disposers:
This disposer must be connected to a grounded, metal, permanent wiring system; or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the disposer.

WARNING
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the disposer is properly grounded. If the plug you are using does not fit the outlet, do not modify the plug or attempt to force the plug into the outlet – have a proper outlet installed by a qualified electrician.

• This disposer must be properly grounded.
• Do not attach ground wire to gas supply line.
• Disconnect power before installing or servicing disposer.
• If three-prong grounded plug is used, plug must be inserted into three-hole grounded receptacle.
• All wiring must comply with local electrical codes.
• Do not reconnect electrical current at main service panel until proper grounds are installed.

NOTICE

• Do not use plumber’s putty on any other disposer connection other than sink flange. Do not use thread sealants or pipe dope. These may harm disposer and cause property damage.
• Do not operate disposer without Anti-Vibration Tailpipe Mount™ as water leaks may result.
• Failure to use the spring-load hose clamp provided voids the warranty.
• To properly drain and prevent standing water in the disposer when utilizing a straight pipe discharge tube, the tube connection opposite the disposer outlet must be lower, not higher, than the disposer outlet.

WARNING When using electric appliances, basic precautions are always to be followed, including:

• Read all instructions before using the appliance.
• To reduce the risk of injury, close supervision is required when an appliance is used near children.
• Do not put fingers or hands into a waste disposer.
• Turn the power switch to the off position before attempting to clear a jam, removing an object from the disposer or pressing reset button.
• When attempting to loosen a jam in a waste disposer, use the self-service wrenchette.
• When attempting to remove objects from a waste disposer, use long-handled tongs or pliers.
• Do not put the following into a disposer: clam or oyster shells, caus-tic drain cleaners or similar products, glass, china, or plastic, metal (such as bottle caps, steel shot, tin cans, or utensils), hot grease or other hot liquids.
• When not operating a disposer, leave the stopper in place to reduce the risk of objects falling into the disposer.
• This product is designed to dispose of normal household food waste; inserting materials other than food waste into disposer could cause personal injury and/or property damage.
• To reduce the risk of injury and/or property damage, do not use the sink containing the disposer for purposes other than food prepara-tion (such as baby bathing or washing hair).
• Do not dispose of the following in the disposer: paints, solvents, household cleaners and chemicals, automotive fluids, plastic wrap.
• FIRE HAZARD: Do not store flammable items such as rags, paper or aerosol cans near disposer. Do not store or use gasoline or other flammable vapors and liquids in vicinity of disposer.
• LEAK HAZARD: Regularly inspect disposer and plumbing fittings for leaks, which can cause property damage and could result in personal injury.

OPERATING INSTRUCTIONS

1. Remove stopper from sink opening and run cold water.

2. Turn on disposer.

3. Slowly insert food waste into disposer.
   WARNING! Position stopper to minimize possible ejection of material while grinding.

4. After grinding is complete, turn disposer off and run water for a few seconds to flush drain line.

DO…

• First turn on cold water and then turn on the disposer. Continue running cold water for several seconds after grinding is completed to flush the drain line.
• Grind hard materials such as small bones, fruit pits, and ice. A scouring action is created by the particles inside the grind chamber.
• Grind peelings from citrus fruits to freshen up drain smells.
• Use a disposer cleaner, degreaser, or deodorizer as necessary to relieve objectionable odors caused by grease build-up.

DON’T…

• DON’T POUR GREASE OR FAT DOWN YOUR DISPOSER OR ANY DRAIN. IT CAN BUILD UP IN PIPES AND CAUSE DRAIN BLOCKAGES. PUT GREASE IN A JAR OR CAN AND DISPOSE IN THE TRASH.
• Don’t use hot water when grinding food waste. It is OK to drain hot water into the disposer between grinding periods.
• Don’t fill disposer with a lot of vegetable peels all at once. Instead, turn the water and disposer on first and then feed the peels in gradually.
• Don’t grind large amounts of egg shells or fibrous materials like corn husks, artichokes, etc., to avoid possible drain blockage.
• Don’t turn off disposer until grinding is completed and only sound of motor and water is heard.

USER MAINTENANCE INSTRUCTIONS

CLEANING DISPOSER
Over time, food particles may accumulate in the grind chamber and baffle. An odor from the disposer is usually a sign of food buildup. To clean disposer:

1. Place stopper in sink opening and fill sink halfway with warm water.
2. Mix 1/4 cup baking soda with water. Turn disposer on and remove stopper from sink at same time to wash away loose particles.
3. Remove Quiet Collar® Sink Baffle and clean by hand or in dishwasher. Do not operate disposer without Quiet Collar® Sink Baffle in place.

RELEASING DISPOSER JAM
If motor stops while disposer is operating, disposer may be jammed. To release jam:

1. Turn off disposer and water.
2. insert one end of self-service Jam-Buster™ Wrench into center hole on bottom of disposer (see Figure A). Work Jam-Buster™ Wrench back and forth until it turns one full revolution. Remove Jam-Buster™ Wrench.
3. Reach into disposer with tongs and remove object(s). Allow disposer motor to cool for 3 – 5 minutes, then lightly push red reset button on the dis-poser bottom (see Figure B). (If motor remains inoperative, check service panel for tripped circuit breakers or blown fuses.)

8 YEAR IN-HOME FULL-SERVICE LIMITED WARRANTY

This limited warranty is provided by InSinkErator®, a business unit of Emerson Electric Co., (“InSinkErator” or “Manufacturer” or “we” or “our” or “us”) to the original consumer owner of the InSinkErator product with which this limited warranty is provided (the “InSinkErator Product”), and any subsequent owner of the residence in which the Product was originally installed (“Customer” or “you” or “your”).
InSinkErator warrants to Customer that your InSinkErator Product will be free from defects in materials and workmanship, subject to the exclusions described below, for the warranty period, commencing on the later of: (a) the date your InSinkErator Product is originally installed, (b) the date of purchase, or (c) the date of manufacture as identified by your InSinkErator Product serial number. You will be required to show written documentation supporting (a) or (b). If you are unable to provide documentation supporting either (a) or (b), the Warranty Period commencement date will be determined by Manufacturer, in its sole and absolute discretion, based upon your InSinkErator Product serial number.

What is Covered
This limited warranty covers defects in materials or workmanship, subject to the exclusions below, in InSinkErator Products used by a consumer Customer for residential use only, and includes all replacement parts and labor costs. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE INSINKERATOR PRODUCT, PROVIDED THAT IF WE DETERMINE IN OUR SOLE DISCRETION THAT NEITHER REMEDY IS PRACTICABLE, WE MAY PROVIDE YOU A REFUND OF YOUR PURCHASE PRICE OR A CREDIT TOWARDS ANOTHER INSINKERATOR PRODUCT.

What is not Covered
This limited warranty does not extend to and expressly excludes:

• Losses or damages or the inability to operate your InSinkErator Product resulting from conditions beyond the Manufacturer’s control including, without limitation, accident, alteration, misuse, abuse, neglect, negligence (other than Manufacturer’s), failure to install, maintain, assemble, or mount the InSinkErator Product in accordance with Manufacturer’s instructions or local electrical and plumbing codes.
• Wear and tear expected to occur during the normal course of use, including without limitation, cosmetic rust, scratches, dents or comparable and reasonably expected losses or damages. In addition to the above exclusions, this limited warranty does not apply to InSinkErator Products installed in a commercial or industrial application.

No Other Express Warranty Applies
This limited warranty is the sole and exclusive warranty provided to the Customer identified above. No other express warranty, written or verbal, applies. No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any other warranty on behalf of Manufacturer. The terms of this limited warranty shall not be modified by the Manufacturer, the original owner, or their respective successors or assigns.

What we will do to Correct Problems
If your InSinkErator Product does not operate in accordance with the documentation provided to you, or you have questions concerning your InSinkErator Product or how to determine when service is needed, please call the toll free InSinkErator AnswerLine® at 1 800-558-5700, or visit our website at www.insinkerator.com. You may also notify us at: InSinkErator Service Center, 4700 21st Street, Racine, Wisconsin 53406 USA.

The following information must be provided as part of your warranty claim: your name, address, phone number, your InSinkErator Product model and serial number, and if necessary, upon request, written confirmation of either: (a) the date shown on your installation receipt, or (b) the date shown on your purchase receipt.
Manufacturer or its authorized service representative will determine, in its sole and absolute discretion, if your InSinkErator Product is covered under this limited warranty. You will be given the contact information for your closest authorized InSinkErator Service Center. Please contact your InSinkErator Service Center directly to receive in home warranty repair or replacement service. Only an authorized InSinkErator service representative may provide warranty service. InSinkErator is not responsible for warranty claims arising from work performed on your InSinkErator Product by anyone other than an authorized InSinkErator service representative.
If a covered claim is made during the Warranty Period, Manufacturer will, through its authorized service representative, either repair or replace your InSinkErator Product. Cost of replacement parts or a new InSinkErator Product, and cost of labor for repair or installation of the replacement InSinkErator Product are provided at no cost to you. Repair or replacement shall be determined by Manufacturer or its authorized service representative in their sole discretion. All repair and replacement services will be provided to you at your home. If Manufacturer determines that your InSinkErator Product must be replaced rather than repaired, the limited warranty on the replacement InSinkErator Product will be limited to the unexpired term remaining in the original Warranty Period. This disposer is covered by Manufacturer’s limited warranty. This limited warranty is void if you attempt to repair the InSinkErator Product. For service information, please visit www.insinkerator.com or call, toll free, 1-800-558-5700.

Limitation of Liability
TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL MANUFACTURER OR ITS AUTHORIZED SERVICE REPRESENTATIVES BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE INSINKERATOR PRODUCT OR THE MANUFACTURER’S OR ITS AUTHORIZED SERVICE REPRESENTATIVE’S NEGLIGENCE. MANUFACTURER SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL MANUFACTURER’S LIABILITY TO YOU EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE INSINKERATOR PRODUCT.
The term “consequential” damages shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or damage to property or equipment. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state.

References

• Leader in Garburators and Hot Water | InSinkErator CA
• Garbage Disposals | Instant Hot Water Dispensers | InSinkErator US
• Environment: Food Waste Diversion | InSinkErator | InSinkErator US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>