Celsicom THR600 Sensors for Radon Temperature and Relative Humidity User Guide
- June 6, 2024
- celsicom
Table of Contents
Celsicom THR600 Sensors for Radon Temperature and Relative Humidity
Quick Guide
Register as a customer and create an account for the Celsiview cloud
service
At the moment the Celsiview cloud service, version two, can be tested, it can
be accessed by clicking on the ”Celsiview 2 Beta” button on celsiview.se. The
instructions below are based on Celsiview 2.
Click on the ”Create new account” button. Fill in all the information needed
to create the ac-count. A verification email will then be sent to the email
address provided in the registration process. Click on the link in the email
to verify the account. If you do not receive an email, plea-se check the spam
mail. Once the account is verified, a page will appear with a link to the
login page.
Adding the sensor to your sensor registry
Go to the Celsiview 2 login page by clicking on ”Celsiview 2 Beta” on
celsiview.se and log in. Se-lect ”Sensor” from the menu and then ”Add new
sensor”. Now scan the sensor or enter the data manually (S/N + control code
written on the sensor). After the sensor data is displayed, click on ”Add this
sensor”. The cost of the sensor is now presented. Accept by adding the sensor
to the shopping basket. Now scan the remaining sensors in the same way.
Click on the shopping basket and view the contents. A summary of the costs is
now displayed. Select or create an invoice recipient. The invoice recipient
should contain all the information needed to be accepted by your finance
department. The references, cost centre, etc. will appear on your invoice.
Click on ”Complete transaction!” to activate the sensor.
Start and activate the sensor(s)
Plug an AC/DC adapter (12V ≥1A, plus on centre pin) into the designated socket
on one short side of the sensor. A short beep will be heard immediately. The
sensor will now look for the ne-arest mobile mast to connect to. When the
connection is complete, three short beeps are heard. The connection can take
up to 4-5 minutes. If nothing happens, restart the sensor. If no three beeps
are heard, there is probably no mobile signal for the NB-IoT network where the
sensor is located. Try moving the sensor slightly.
For 45 minutes, the sensor now sends data every 3 minutes. After a total of 60
minutes, the sen-sor switches to transmitting less frequently to save battery
power. To restart the above process or if the sensor does not connect
properly, disconnect one of the batteries, wait 60 seconds and reconnect it
again.
Add/change measurement locations linked to the sensor
Click on ”Sensor” in the menu. Click on the plus sign at the far right of the
line where the sensor is displayed. Enter a prefix, e.g. Sensor 1, Cellar or
similar. Click on ”OK”. Locations have now been created for the various
measurements. By clicking on ”Locations” in the menu, the measurement
locations are now visible.
To change a setting/name of a location, click on the tool icon on the right of
the row or click on a row and select ”Go to settings”.
By clicking on the star symbol on the far right of a location row, or
selecting ”Make into favourite” after clicking on a row, that measurement will
appear as a favorite (widget) on the home screen.
(Menu item ”Home”)
The options ”Settings”, ”Reports” and ”Make into favourite” etc. are also
accessible by simply clicking on any row/location on the ”Locations” page.
Reports
To print or export reports/measurements, click on ”Reports” in the menu.
Select what to display in the report/graph by the menu options above the
graph. It also selects the time period you want to look at. Click on the
”Export” button to download or send the report as e.g. an Excel file or PDF.
My business
In the ”My business” menu, sites can be structured into different
groups/folders. Right-click on
”Groups and locations” to create a group/folder. Then drag and drop the
measurement locations you want into any group.
A group or location can also be shared with another person by right-clicking
on the location or group and selecting ”Share”. Select ”Create new user”,
enter the email address of the person to be assigned to the site/group.
Automatically, the username of that person will be set to the same as the
email address. Click on ”OK”. The new recipient now appears in the list of
selectable recipients. Select the rights the new user should have. Click on
”OK”. The new user will now receive an e-mail asking him to choose a password.
The new user can then log in with their details and will have access to what
has been distributed.
Add alarm recipients
Log in to the account. Click on the username in the top right corner. Select
”Alarm handling”. Add the email addresses/SMS numbers where alerts should be
sent. Test the alarm by clicking on the letter symbol of the recipient to
which the test should be sent. NOTE! Make sure that it get delivered.
Support
All support is handled by our distributors. See celsicom.se for more
information. User manuals and other support material are available at
support.celsicom.se
Specifications
Radon measurement principle| Filtered diffusion to high-voltage measuring
chamber
---|---
Radon detection method| Alpha spectrometry
Range| 0 – 4 000 Bq/m3, -30°C to +70°C, 0-100% RH
Radon integration time (time to stable measured values)| 1 hour after start-up
Uncertainty| Radon: typically within 25% at 200 Bq/m3 and 20°C. Tempera- ture:
±0.5°C. RF: ±3%.
Connection| NB-IoT (LTE Cat NB1) B20
Power 23 dBm
Power| 12V DC / 1A (+ center pin)
Measurement and trans- mission interval| Adjustable by users via the Celsiview
cloud service. Default is measurement every 5 minutes and transmission every
30 minutes.
Memory| 200 measurements
Size| 225 x 110 x 63 mm
Weight| 510 grams
Operating range| 0 – 60°C, 0-90% RH, non condensating
Calibration| The unit is calibrated and adjusted at the factory
IP-class| 20
Certificate| CE
- Celsicom AB
- Härdgatan 28 A, 432 32 Varberg SVERIGE
- celsicom.se
- support.celsicom.se
- Version av bruksanvisning: 9