GOLD NOTE Valore 425 Lite Italian Turntable User Manual
- June 6, 2024
- GOLD NOTE
Table of Contents
- GOLD NOTE Valore 425 Lite Italian Turntable
- PACKAGE CONTENT
- INTRODUCTION
- KEY FEATURES
- TECHNICAL SPECIFICATIONS
- SET-UP INSTRUCTIONS
- INSTALLING THE PLATTER
- ANTI-SKATING AND COUNTERWEIGHT ADJUSTMENTS
- VTA SETUP
- POWER SUPPLY
- POWER ADAPTER AND SPEED CONTROL
- CARTRIDGE ALIGNMENT
- WARRANTY
- TROUBLESHOOTING
- IMPORTANT SAFETY INFORMATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GOLD NOTE Valore 425 Lite Italian Turntable
PACKAGE CONTENT
- 1 Turntable Plinth
- 1 Dust Cover completed with hinges
- 1 Power Adapter with connecting cables
- 1 B-5 Ball Bearing with tonearm cable already installed
- 1 cylindrical counterweight 110 g
- 1 additional counterweight 28.5 g
- 1 Anti-skating
- 1 Platter Spindle tip that clamps the platter
- 1 oil jar
- 1 Drive Belt
- 1 Allen Key of 2,5mm for arm lift board blocking
- 1 Allen Key of 2,0mm for din pillar removing
- 1 Allen Key of 1,5mm for VTA tonearm adjustment, lift cueing removing, anti skate cylinder adjust
- 1 Protractor, Overhang for cartridge adjustment incorporates even a Stroboscope for Speed Adjust
- 1 GN Stylus Gauge
- 1 Felt Matt
- 1 User Manual
INTRODUCTION
- GOLD NOTE® manufactures a wide range of prestigious and sophisticated audio products featuring unique and innovative technical and aesthetic characteristics.
- The Valore 425 Lite is the evolution of the Valore (400mm) produced by Gold Note since the 2010, the entry level Gold Note High-End Audio turntable merges audio performance, with high grade of finish and elegant look.
- The Valore 425 Lite features a 30mm thick plinth wisely shaped and cut around the bearing of the platter and the motor to drastically reduce all unwanted vibrations.
- The Valore 425 Lite platter is manufactured using a special 20mm thick sandwich MDF/POM material derived directly from the top level Gold Note turntables as well as the 60mm long platter bearing and spindle, finely machined to achieve the best audio quality of its category.
- Besides the Valore 425 Lite platter is designed to stay only 3mm closed to the turntable plinth. Such small platter/plinth interference allows reducing turbulence featuring a great noiseless rotational stability.
- The Valore 425 Lite features a 12Volt synchronous motor developed by Gold Note using a specially designed micro-controlled D/A Converter able to perfectly reshape the sinusoidal AC curve.
- Powered by a new Gold Note property design the D/A Convertermicrocontrolledmotorguaranteesahighprecision speed enabling the motor having a perfect phase also controlling the power of the motor the best having a strong high torque force starts, then smartly reducing the intensity of current once the speed is correctly stabilised controlling the vibration at all.
- Besides the new top-class polished hourglass-shaped motor pulley allows the turntable belt spins smoothly reducing the wow& flutter and noise precisely.
- The Valore 425 Lite size allows equipping the plinth with 9” tone arms. The turntable is offered as package with a Gold Note dedicated 9” arm and a mould high resistance, thick and heavy Dust Cover to avoid resonance feedback.
- The theValore425Litethoughisundoubtedlyanextraordinary good turntable to be used in a large variety of prestigious High-End Audio systems it is an extremely reliable, easy to use turntable for all audio enthusiasts looking for performance, cosmetic but efficiency at the same time.
- The plinth of the Valore 425 Lite is available in black or white lacquer.
KEY FEATURES
This section describes the special features of the Valore 425 Lite turntable, the construction details, the reasons for the technical choices and the originality of the design.
- The Valore 425 Lite is a rigid turntable that uses a plinth made of high damped lacquered MDF.
- The plinth bears three acrylic spikes for ensuring great insensitivity to vibrations. The turntable platter is made of 20mm thick special 20mm thick sandwich MDF/POM material chosen for its damping ability.
- The spindle is a high class machined stainless steel split in two pieces able to clamp the platter through its conical shape. The spindle is 60mm long to ensure top performance.
- A large longitudinal groove is located on its axis, which allows the lubricating oil to run in constant manner. The longer spindle eradicates any pendulum effect and distributes the inertial energy along its entire axis, completely annulling any type of lateral friction.
- The ThebearinghousestwoTeflon/Graphiterectifiedbearings that handle the spindle with the help of a customised bottom platter bearing enables very low noise and extra precise rotational stability.
- The platter bearing is threaded outside in order to be tightly blocked to the plinth of the turntable on its own axis to allow a very firm and precise coupling.
- The thecust omA C 12 Voltlow voltage electronically controlled Valore motor allows 33⅓ & 45 rpm electronic speed control.
- The custom AC 12 Volt micro-controlled motor allows 33⅓rpm & 45rpm electronic speed control and pitch adjustment. Besides the special motor guarantees a perfect rotation stability and great torque in complete silence.
TECHNICAL SPECIFICATIONS
-
Wow & flutter: 0,3%
-
Rumble: -72dB
-
Speed: 33⅓rpm and 45rpm ±0,1%
-
Speed Changing: electronic with fine pitch control
-
Transmission: 70 shores rectified NBR belt Motor: high torque 12V synchronous
-
Platter: 20 mm black solid HDF covered with POM Platter Spindle: Split-Spindle™ clamping design Platter Bearing: Chromed Steel 5mm ball bearing Tonearm: Gold Note B-5
-
Dust Cover: transparent acrylic with hinges
POWER -
Power supply: 18V output
-
Power consumption: max 20W
-
100-240V / 50-60 Hz
DIMENSIONS AND WEIGHT
Dimensions: 425 W x 170 H x 360 D mm
Weight: Kg. 7 net – Kg. 11.5 boxed
SET-UP INSTRUCTIONS
FIRST OPERATION
- Please remove carefully all the protecting foam and check the items listed are all supplied.
- Place the turntable deck on a leveled surface, the best is a wall shelf immune to footfall, then level the turntable.
- Plug the tonearm cable pre-installed to the amplifier phono input.
- Install the counterweight into the rear arm wand of the arm adjusting the correct cartridge tracking weight with the help of a precision scale (not supplied).
- Install the turntable belt surrounding the hourglass motor pulley and the platter outer perimeter.
- Plug the Power Adapter cable to the S/Steel rounded plug motor cover underneath the turntable plinth bottom left side corner.
POSITIONING THE VALORE 425 LITE
Your VALORE turntable has been designed for home Hi-Fi systems. It must be
protected from direct sunshine rays and humidity. Do not put it close to
strong heating sources, electrical and electronic motors, mobile phones etc.
The leveling and positioning on a solid shelf, as explained in the previous
chapter, is fundamental to ensure the best audio performances.
OPERATING THE 33⅓rpm & 45rpm CONTROL
The turntable is fully controlled by an electronic power supply.
TURNTABLE SPEED CONTROL ADJUSTMENT
The turntable is fully controlled by an electronic power supply operating
the Turntable 33⅓rpm & 45rpm.
- Outer Button Start and Stop the 33⅓rpm speed.
- Inner Button Start and Stop the 45rpm speed. The turntable also features a fine speed adjust “Pitch Control” allows a very fine adjust of the speed of the turntable.
PITCH CONTROL MODE
To enter the PITCH CONTROL MODE press and hold for 4 seconds both 33⅓rpm
and 45rpm buttons while the turntable is spinning.\ When the red LED light
shuts down, the unit is ready for the fine speed adjustment.
PITCH –
Press repeatedly the 33⅓rpm button until the correct speed is reached. The
LED light flashes every time the button is pressed.
PITCH +
Press repeatedly the 45rpm button until the correct speed is reached The
LED light flashes every time the button is pressed.
The TURNTABLE SPEED CONTROL unit records permanently in the turntable memory the speed adjusted singularly for both 33⅓rpm and 45rpm even if the unit is unplugged from the AC wall.
INSTALLING THE PLATTER
CONTENT OF THE TURNTABLE BOX
- Platter
- Oil Vessel
- Ball-bearing
- Platter Spindle Tip + Platter spindle
INSTRUCTIONS
- Remove plug from the middle of the turntable
- Insert the Ball Bearing into the Bearing Housing* of the turntable taking care to center it on the bottom seat
- Oil the Platter Spindle as shown in figure 3
- Insert the Platter Spindle into the Bearing Housing
- Lay the Platter on the Platter Spindle
- Secure the Platter Spindle Tip in the threaded hole of the Platter Spindle
PLEASE NOTE: the Bearing Housing is already installed in the plinth of the turntable. Do not remove it.
INSTALLING THE BELT
Wrap the belt around the pulley and the platter as shown in the pictures:
ANTI-SKATING AND COUNTERWEIGHT ADJUSTMENTS
- ANTI-SKATING nylon wire with bullet counterweight
- ANTI-SKATING adjustment bar
- TONEARM COUNTERWEIGHT: to set up the correct tracking force depending on the phono cartridge in use
INSTALLING THE ANTI-SKATING SYSTEM
- Slip the loop of the ANTI-SKATING nylon wire over the groove of the ADJUSTMENT BAR
- Feed the wire through the loop of the SUPPORT HOOP
- Adjust the ANTI-SKATING force choosing the correct groove on the ADJUSTMENT BAR
VTA SETUP
Loose the Hex-bolt indicated by the arrow on the collar using the 1,5mm Allen Wrench supplied to lift up or down the arm correctly adjusting the VTA as necessary.
POWER SUPPLY
POWER SUPPLY ADAPTER
Is necessary to use the correct AC plug based on your local area. Size:
67.3 x 43.5 x 37.5 mm
PLEASE NOTE: Before plugging the AC adapter plug the round connector indicated here.
POWER ADAPTER AND SPEED CONTROL
CONNECTING THE POWER SUPPLY ADAPTER
Use only the original GOLD NOTE AC adapter to power the turntable to ensure
the correct functioning.
PLEASE NOTE: Before plugging the adapter in to the AC make sure the connector is plugged into the turntable
TURNTABLE SPEED CONTROL
- OUTER BUTTON starts and stops the 33⅓rpm speed. When the 33⅓rpm is playing its red LED light turns on.
- INNER BUTTON starts and stops the 45rpm speed. When the 45rpm is playing its red LED light turns on.
The Valore 425 Lite also features a fine speed adjustment “Pitch Control” function to achieve a precise control over the speed of the turntable.
PITCH CONTROL MODE
To enter the PITCH CONTROL MODE press and hold for 4 seconds both the
33⅓rpm and the 45rpm buttons while the turntable is spinning at 33⅓rpm or
45rpm until the red LED light shuts down. The unit is now ready to adjust the
speed with the help of the stroboscope.
- PITCH – press in sequence the 33⅓rpm button until the correct speed is reached. The LED light flashes every time the button is pressed.
- PITCH + press in sequence the 45rpm button until the correct speed is reached.
The LED light flashes every time the button is pressed.
To switch off of the PITCH CONTROL MODE press and hold for 4 seconds both the
33⅓rpm and the 45rpm buttons until the LED light is on and steady again.
CALIBRATION: CARTRIDGE OVERHANG, ALIGNMENT AND SPEED
Our turntables and tone arms are always supplied with the Gold Note Calibration Tool to calibrate correctly the setup. With this tool you will be able to adjust:
- Phono Cartridge alignment
- Overhang
- 45rpm and 33⅓rpm speed (requires a strobe light)
SPEED ADJUSTMENTS
Check the speed with the help of a strobe light (eventually a home NEON can
also work). When the speed is correct you will be able to see the sequence of
black rectangular signs as if they were stable and fixed while the platter is
spinning. The outer line is to check the 33⅓rpm The inner line is to check the
45rpm
OVERHANG
To set the correct overhang the Calibration Tool must be inserted on to the
turntable record pin and the cartridge Tip must be positioned on top of the
pin. Adjust the position of the cartridge until the suggested overhang of the
phono cartridge is reached as indicated by the manufacturer.
CARTRIDGE ALIGNMENT
PHONO CARTRIDGE ALIGNMENT
To correctly align the phono cartridge and achieve the best tracking
position, point the tip of the phono cartridge into the white circles as in
the picture below. The body of the phono cartridge must be aligned to the
vertical stripes in order to achieve the best position for musical
reproduction.
DETACHABLE DUST COVER
The new Gold Note dust cover features detachable hinges, a new proprietary
design developed to let you enjoy your turntable at the best in any situation.
The new dust cover is incredibly versatile and allows the usage of the
turntable with or without it.
We are proud to offer this new solution to our clients to help them preserve
their turntables in ideal functional and cosmetic conditions.
The new design also provides a stop point at about 90° to the dust cover: in
this position it automatically stops and the hinges will hold the dust cover
avoiding overturning.
Removing the dust cover is simple and quick:
lift the dust cover until it reaches the 90° stop point and it’s completely
opened, then gently slide it towards LEFT (facing the turntable) to detach it
from the plinth.
PLEASE NOTE: the dust cover can be removed and reinserted only when it’s in its resting position, completely opened at 90°.
WARRANTY
PRODUCT REGISTRATION
- We recommend to register the unit on our internet website within 15 days from the purchase at www.goldnote.it/product-registration
- If the unit is not registered correctly or has been purchased from a different country of the purchaser home address the unit will not be covered by any warranty and the registration will be refused.
- Please note that the warranty does not cover in any case: Tubes, Phono Cartridge Stylus and Batteries.
WARRANTY
- All Gold Note products come with a warranty against defective materials and workmanship.
- Any service and inspection must be carried out by a Gold Note dealer or distributor so in case you need any assistance with this product, please contact the seller.
- If you experience any problems locating your official Gold Note dealer or distributor, please check our website.
PLEASE NOTE
Descriptions and technical characteristics may vary at any time and without
notice.
WARNING
- Gold Note products should only be opened, serviced and inspected by certified Gold Note technicians and dealers.
- Work performed by unqualified personnel may cause serious damage or personal injury. Opening of the product by non-authorized personnel will void the guarantee. In this case, contact your dealer to be advised on how the fault can be solved.
- Do not return any object directly to the factory or to the distributor without being authorized to do so.
TROUBLESHOOTING
PROBLEM | CAUSE | SOLUTION |
---|---|---|
Levelling the turntable | The turntable is not levelled | With a spirit level, |
only level the Turntable Platter through its shelf layer eventually screwing its feet just for very fine adjustment, take care of levelling the platter on its vertical and horizontal lines.
Be sure that the turntable layer is enough solid and rigid to support the weight of the turntable Easily.
Cleaning the turntable| The turntable is dirty and requires cleaning| With EXTREME care use ONLY very soft 100% cotton cloth to sweep dust and stains out.
Any acid or not extremely soft cloth will irreversibly damage the turntable fine aesthetic. Do not use any alcohol to clean the turntable anodised label, pulley and motor spindle.
Only dry cloth is allowed.
Motor heating| The motor is too hot| AC synchronous motors as the ones used by
Gold Note may warm up to 50° Celsius without creating any problem.
Noise on startup| The turntable produces a slight rubbing noise upon startup|
It is normal for the belt to produce a slight noise when starting.
For spare parts visit the official Gold Note store at:
www.akamaiaudio.it
IMPORTANT SAFETY INFORMATION
CAUTION!
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER ONLY TO QUALIFIED GOLD NOTE SERVICE PERSONNEL
FOR SERVICE
WARNING!
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE
Do not disassemble any part of the product. Do not use any part of the product for other purposes. For service and problems of any kind, contact qualified Gold Note personnel. Protect the product from rain and humidity and keep away from heat sources, electric and electronic motors etc. The power Chord supplied must be used only on this unit. Gold Note does not have responsibility for any improper use of this unit.
This appliance has a serial number located on the rear panel. Please record the model and serial number and retain them for your records.
- Serial Number:
- Model:
-
Follow the instructions and store them
-
Heed all warnings
-
Do not use this apparatus near water
-
Clean only with a dry cloth
-
Do not install near heat sources such as radiators, heat registers, stoves or other apparatus
-
Do not defeat the safety purpose of the polarised or grounding-type plug: a polarised plug has two blades with one wider than the other.
A grounding-type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet. -
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
-
Only use attachments/accessories specified by the manufacturer.
-
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. -
Unplug this apparatus during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified service personnel only.
Servicing is required when the apparatus has been dam-aged in any way (such as when the power cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture) and in any case when the apparatus does not operate normally or has been dropped.
goldnote_italy
Gold Note Audio
Gold Note
Akamai S.r.l. service@goldnote.it
www.goldnote.it
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>