V-TAC VT-2000- P1 Glass Panel Heater Instruction Manual

V-TAC VT-2000- P1 Glass Panel Heater

WARNING SYMBOLS USED

Indicates a potentially hazardous condition that, if not avoided, may result in death or serious injury.

| WARNING OF HOT SURFACE SYMBOLS USED

This symbol indicates dangers to the life and health of persons due to hot surface.

---|---

CAUTION SYMBOLS USED

Caution, risk of electric shock.

| This marking indicates that this product should not be disposed of with other household wastes
DO NOT COVER SYMBOLS USED

__          This symbol located on the device indicates that it is prohibited to place objects (such as towels, clothes etc.) above or directly in front of the device.

In order to avoid overheating and fire hazards, the heater must not be covered.

SAFETY WARNINGS & CAUTION

WARNING!
Please ensure to read all the safety warnings and instructions before using the product. Failure to follow the same may result in electric shock/ fire/ serious injury.

•  Please keep the manual handy for future references. You may also contact support@vtacexports.com for a pdf version of the manual.
•  Incorrect operation and improper handling can lead to faults on the device and injuries to the user
•  Remove the packaging and make sure that the appliance is intact. If in doubt, do not use it and contact our Technical team at support@vtacexports.com  Packaging materials (plastic bags, polystyrene, staples etc.) must be kept out of the reach of children as they could be hazardous.
•  This appliance must only be used for the purpose for which it has been manufactured, i.e. for additional electrical heating in rooms. Any other use is considered improper and therefore dangerous. The manufacturer is not respon-sible for any damage caused by improper, incorrect or unreasonable use.
•  If the appliance is faulty and/or operating incorrectly, switch it off without tampering with it. If the above is disregarded, the safety of the appliance may be compromised.
•  Before you put the plug into the socket, please check that the type of current and mains voltage correspond to the instructions on the name plate/sticker on the appliance.
•  Do not immerse the unit or mains plug in water or other liquids. Risk of electric shock! However, if this should occur, remove the mains plug immediately and then have the unit checked by an expert before using it again.
•  Ensure that the mains cable does not hang over sharp edges or allow it to become trapped.
•  If the supply cord is damaged, it must be replaced by the manufacture, its service agent or similarly qualified persons in order to avoid a hazard.
•  The power cord on this appliance must NOT be replaced by the user. If the cord is damaged or requires replace-ment, contact qualified personnel only.
•  Ensure that all electric cables outside of the device are protected from damage (e.g. caused by animals). Never use the device if electric cables or the power connection are damaged!
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
•  Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
•  Ensure to keep the suction grille clean.
•  Children of less than 3 years should be kept away unless continuously supervised.
•  Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
•  Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
•  This appliance is not a toy! Keep away from children and animals. Do not leave the device unattended during operation.
•  Do not use the device in small rooms if persons are present who cannot leave the room independently and who are not under constant supervision.
•  Do not use the device in potentially explosive rooms.
•  Do not use the device in an aggressive atmosphere.
•  Ensure the device is set up in an upright and stable position.
•  After cleaning the device, allow the device to dry out. Do not use the device when wet.
•  Do not touch the device with wet or damp hands or feet.
•  Do not expose the device to directly squirting water.
•  Do not use the device near sources of water such as baths, showers or swimming pools. Risk of electric shock!
•  Never insert any objects or limbs into the device.
•  Do not cover or transport the device during operation.
•  Do not remove any safety signs, stickers or labels from the device. Keep all safety signs, stickers and labels in legible condition.
•  Do not sit on the device.
•  Check accessories and connection parts for possible damage prior to every use of the device. Do not use any defective devices or device parts.
•  Ensure to insert the mains plug into a properly secured mains socket.
•  In order to avoid overheating, it is advisable to unwind the entire length of the power cord.
•  Before cleaning or carrying out maintenance on the device, care or repair work on the device, disconnect it from the electrical mains by removing the plug from the electrical outlet.
•  Switch off the device and remove the plug from the electrical outlet when not in use.
•  Defective power cables pose a serious health risk!
•  During the installation of the device ensure the minimum distance between the wall and objects is a minimum of 50CM to 100CM.
•  To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1m from the air outlet.
•  Make sure that the air inlet and outlet are not obstructed.
•  Do not place the device on the combustible ground.
•  Before maintenance, cleaning or transporting the device allow the device to cool down completely.
•  Do not obstruct the ventilation or heat dispersion openings.
•  Do not use the appliance immediately below a fixed power outlet.
•  In order to avoid overheating, do not cover the heater.
•  The heater must not be used if the glass panels are damaged.
•  The heater must not be located immediately below a socket outlet.
•  To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1m from the air outlet.
•  Keep the appliance away from hot objects (e.g. Hotplates) and open flames.
  CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

INTRODUCTION & WARRANTY
Thank you for selecting and buying the V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any other queries, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 2 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. This product is warranted for manufacturing defects only.

NOTE: This product is only designed for use inside well-insulated rooms or for occasional use

PRODUCT FEATURES

1. Touchscreen control panel
2.  LCD Display
3.  Infrared Remote control
4.  Feet with lockable swiveling wheels.
5.  Timer from 1 to 24 hours to turn on/off as per desired time.
6.  Self-resetting thermostat and thermal fuse
7.  Noiseless heating element
8. Temperature setting from 15°C-35°C.
9.  Tempered glass panel
10.  Splash water protected (IP 24)
11. Cable length 1.5M (EU Plug)

TECHNICAL SPECIFICATION

SKU| 8663| 8664
UNIT COLOR| WHITE| BLACK
POWER (WATTS)| 2000W| 2000W
TEMP RANGE| 15°C – 35°C| 15°C – 35°C
TIMER RANGE| 1 Min – 24 Min| 1 Min – 24 Min
INPUT VOLTAGE| AC:220-240V, 50/60Hz
CURRENT| 8.7A| 8.7A
PLUG TYPE| EU| EU
CABLE LENGTH| 1.5 Meters| 1.5 Meters
REMOTE DISTANCE| 6 Meters| 6 Meters
DIMENSION (LxWxH)| 830x260x520mm| 830x260x520mm
NET WEIGHT (Kgs)| 7.7| 7.7
GROSS WEIGHT (Kgs)| 9.2| 9.2

PACKAGING CONTENTS

APPLICATIONS

1.  Note: This product is only designed for use inside well-insulated rooms or for occasional use.
2.  The device must only be used in closed rooms.

NOTES

1. Carefully unpack the box and remove the device and accessories. Place the device (glass convector heater) on a protected surface. Ensure the feet is properly fixed on the device.
2.  Please check if all the articles are included and there is no damage seen.

INSTALLATION INSTRUCTIONS (FOOT ASSEMBLY)

Please ensure you have all the accessories (included) foot and screws to assemble on the device

1. Please make sure the device is not connected to power.
2.  Carefully place the device (glass convector heater) down (as shown below) on a protected surface. Ensure the tempered glass surface is facing downwards.
3.  Using the ST4123 screws install the feet on the device (glass convector heater). Ensure the feet is properly fixed on the device.
4.  Carefully lift the device up to its position. You can now move and place the device in the desired location you choose.
   NOTE: Using the lock feature on the brakes you can park the device on the location to ensure its stability.

PRODUCT COMPOSITION/ PART NAME

Swiveling Wheels

| ****

Foot

| Locakable swiveling wheels| ****

ON/OFF Switch

| ****

Temperature Sensor

FUNCTIONS

NOTE : The device will indicate a beep sound while setting the functions (Mode, Time, Temperature, “+” & “-” )

MINIMUM DISTANCE PLACEMENT OF THE DEVICE
Glass convector heater must be placed on the desired location carefully and ensure the distance between the wall and objects is a minimum of 50CM to 100CM

NOTES
Stand BY Mode: When the device is restarted after its cooldown period the device will start in Standby mode (25°C-27°C). Cool Down Period – After using the heater please power off the device and allow minimum 30 minutes for the device to cool down. Please note the device cool down period will be subjected to the usage period, the room size and other factors. Due to this please allow minimum 30 minutes if required please allow more time until the device has been completely cooled down.

INSTRUCTIONS: USING THE DEVICE

1. Once the device has been positioned successfully maintain the minimum distance placement of the device (Min 50-100CMs).
2. Ensure power is switched OFF and connect the EU plug into the power outlet and switch the power ON.
3. On the side of the device, set the switch (Point E) to ON position (Refer Figure 1). The device will start with a beep sound and the LCD display will light up.
4.  Press the power button on the touch panel or remote control to activate the heater. The device will enter standby mode displaying (25°C-27°C) on the LCD display.
5.  Press the Mode button on the control panel/ remote control (Figure 2 and Table 1), the device will start in Low-temperature heating mode. You can switch between Frost-Low temperature and High-temperature mode by using the mode button on the control panel/ remote control (Figure 2 and Table 1)

Modes: Tap on the Mode button on the touch panel/ remote control (Figure 2 and Table 1) to switch between Frost-Low-High modes.

Frost Mode: Operates at 1.5W (Designed with a thermostat, frost mode ensures keeping small rooms free from frost).

Low-temperature Mode: Operates at 1000W (Allowing the temperature range to be set from 15°C-35°C.).
High-temperature Mode: Operates at 2000W (Allowing the temperature range to be set from 15°C-35°C.).

TRANSPORTATION
Please ensure to transport the device properly, failure to do so may result in damaging the device. Before transporting or moving or adjusting the device please ensure to follow the below steps.

1.  Switch off the power and unplug the mains plug from the mains socket.
2.  Ensure the device is cooled down properly.
3. If the brake was applied, release the brake from the wheels.
4.  Now you can transport or move the device. Do not use the power plug to move or transport the device.

STORAGE

Before storing the device please ensure to follow the below steps.
Note : Remove the batteries from the remote control and ensure to store the battery in dry and protected environment.

1. Switch off the power and unplug the devices main plug from the mains socket.
2.  Ensure the device is cooled down properly.
3.  Ensure the environment is dry and protected from dust, sunlight, frost.
4. Make sure the device is stored in upright position. Do not place it downwards.
5. We recommend to put a cover on the device to protect from dust.
6.  Ensure there is no other device or object placed on top of the device from any damage being caused to the device.

MAINTENANCE

1. Please do not clean the device immediately after using. Allow for the device to cool down completely first and then switch OFF the device and unplug the device from the main socket.
2.  Please ensure not to use damp/wet hands before turning off the switch power or unplugging the device.
3.  Clean the device with soft, damp cloth ONLY and DO NOT use any abrasive substances to clean the device as it will result in damaging the device.
4.  DO NOT submerge any part of the product in the water.

TROUBLESHOOTING

REMOTE CONTROL IS NOT WORKING:

1.  Ensure the distance between the remote control and device is maximum 6 meters
2.  Ensure the batteries are installed correctly and charged.
3.  If batteries are discharged please charge or install new batteries.

HEATER IS NOT WORKING:

1.  Ensure the plug is connected to the power and is switched ON.
2.  Ensure the side switch of the heater is powered ON. (Set the switch (Point E) to ON position (Refer Figure 1 and Table 1)
3.  Turn OFF the power and inspect there are no damages to the power cord and plug.
4. Check if the heater is in standby mode. If yes then set the desired mode temperature to start using the heater. NOTE: If any part of the heater needs to be replaced please ensure it is only replaced by qualified person only.

Please scan the QR code to access the manual in multiple languages.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>