TANE ALARM PRODUCTS TWC PIR345 Wireless Interior Motion Detector Instruction Manual

TANE ALARM PRODUCTS TWC PIR345 Wireless Interior Motion Detector

Congratulations:
Properly installed, your TANE ALARM PRODUCTS TWC PIR345 Interior PIR Motion Detector will provide dependable operation and security. Please read and follow these instructions carefully.

Product Design

Parts description

1. Fresnel lens
2. LED indicator
3. Ball Joint
4. Sensor
5. Tamper switch
6. LED indicator
7. Battery holder

PRODUCT DESCRIPTION

The TWC PIR345 utilizes a dual-element pyroelectric infrared sensor. It’s able to accurately detect the human infrared spectrum, and features a high- sensitivity setting
with low false alarm rates. The transmission frequency of TWC PIR345 is 345MHz.
This product is widely used for Banks, Post Offices, Malls, Private Homes, Jewelry Stores, Hotels and similar places where a high level of security is required.
A signal is triggered by the following condition:

1. Human motion is detected;
2. The Tamper Switch is switched off or on;
3. The battery voltage is below the threshold of 2.6V;
4. Supervisory signal transmission is the interval of about 70 minutes.

PRODUCT SPECIFICATIONS

• Sensing angle: 120′
• Sensor range: 30 ftx40 ft.
• Suggested Installation Height 7.2 ft. above floor level
• Sensor type: Dual element pyroelectric infrared sensor
• Transmitter Frequency: 345 MHz
• Wireless Signal Range: >300 ft (open air, line of sight)
• Battery Type: One (1) CR2/CR15270 3V Lithium Battery or
• Equivalent Battery Life: 3~5 years
• Operating temperature: 14~122’F
• Relative humidity: 5~90% no condensation
• Dimension: 3.51 inx2.06 inx1.32 in

Installation Instructions:

Battery Installation
Unitin(mm)

Jumper Installation

Motion detection sensitivity can be selected by a Jumper switch.
The ON position is for High Sensitivity (detection distance is greater than 315 in(Bm).
The OFF position is for Normal Sensitivity [detection distance is less than 315 in(Sm).

PIR Sensor Installation  Unitin(m)

Operating Instructions

Warming up
After powering up, the red LED will start flashing, indicating the motion sensor is warming up. After 30 seconds, the LED will stop flashing, indicating the warm-up is complete. The motion detector will then enter the Walk-Test Mode.

Walk-Test Mode
The Walk-Test mode is used to test the motion detector’s pattern of coverage. Each time motion is detected the LED will remain on for about 6 seconds, and an alarm message will be transmitted.

When the LED goes out, the sensor is ready to detect motion again. If no motion has been detected for 2 minutes, or if 40 motions have been detected, the motion detector will exit the Walk-Test mode and enter the normal operation mode.

Normal Operation Mode
After completing the Walk-Test Mode, the motion detector will enter the Normal Operation Mode. In the Normal Operation Mode, if human motion is detected an alarm message will be transmitted immediately, and the motion detector will not transmit again for a period of 3 minutes.
In Normal Operation Mode, if the tamper switch is triggered, an alarm message will be transmitted immediately.

Low Battery
In Normal Operation Mode, the LED will flash when a low-battery condition is detected. The LED will continue to flash until the battery has been replaced, and the low battery condition has been corrected.

Caution
Choose the best tilt-angle and installation height to make sure human motion can be detected within the motion detector’s pattern of coverage.
Avoid positions that are close to air conditioners, refrigerators, electric heaters, electric ovens, and other devices which can cause rapid temperature changes.
Do not position the motion detector in direct sunlight or where significant vibration occurs.

Lens Pattern

Side View

Top view

Mounting the PIR Sensor

Product Dimensions

Important Installation and Use Tips

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>